Yamaha 01V96i Reference Manual - Page 83

Remote Control

83

01V96i—Reference Manual

Remote Control

Remote Control

This chapter describes the Remote function, which enables

you to control external equipment directly from the 01V96i

top panel.

About Remote Function

The 01V96i’s Remote function enables you to control external

DAW (Digital Audio Workstation) equipment, MIDI devices,

etc.

There are two types of Remote functions (Remote and

Machine Control):

■

REMOTE (Remote Layer)

To use these types of Remote functions, you must connect the

01V96i to a target device via USB or an optional

MY16-mLAN card installed in the slot, and operate the faders

and [ON] buttons on the top panel to control the external

device remotely.

You can specify a target device and parameter values on the

DIO/Setup | Remote page. This layer is enabled when you

turn on the LAYER [REMOTE] button. During Remote oper-

ation, the controls on the top panel enable you to control the

external device. (You cannot adjust the 01V96i’s parameters

unless you select a different layer.)

You can assign functions of a target device to the controls on

the top panel of the 01V96i by using Remote layer. The fol-

lowing targets are available for remote control:

• ProTools

You can remotely control Digidesign Pro Tools.

• Nuendo

You can remotely control Steinberg Nuendo.

• Cubase

You can remotely control Steinberg Cubase.

•

General DAW

You can remotely control DAW software that supports

the protocol used by Pro Tools.

•

User Defined

You can also assign MIDI messages to the faders or [ON]

buttons to remotely control a connected MIDI device,

such as a synthesizer.

•

User Assignable Layer

You can combine the 01V96i channels to create a custom

layer. (See Owner’s Manual for more information on this

function.)

■

Machine Control

By using MIDI Machine Control commands and the

DIO/Setup | Machine page, you can control an external

recording machine that is connected to the 01V96i MIDI

port, USB port, or optional MY16-mLAN card installed in

the slot.

Pro Tools Remote Layer

The 01V96i features Remote Layer target especially designed

for controlling Pro Tools.

Connections and Configuring

Pro Tools

Follow the steps below to connect the 01V96i to your com-

puter via the USB port so that you can control Pro Tools from

the 01V96i.

■

Configuring Windows Computers

1.

Download the Yamaha Steinberg USB Driver

from the following URL.

http://www.yamahaproaudio.com/

2.

Install the driver in your computer as

described in the installation guide included in

the downloaded file.

3.

Connect the 01V96i TO HOST USB port to a

USB port on your PC using a USB cable.

4.

Make the necessary settings in Pro Tools.

Refer to the Pro Tools Owner’s Manual for more informa-

tion about Pro Tools settings.

Tip:

To control external devices from the 01V96i, you can also use

the User Defined buttons. Refer to “Other Functions” on page

109

for more information.

Note:

You cannot control Pro Tools via MIDI connections. Be sure

to connect your computer via the USB or an optional

MY16-mLAN card installed in the 01V96i slot.

Section	Page
How to Use This Reference Manual	1
Contents	2
Contents of the Owner’s Manual (Booklet)	3
Function Tree	4
Control Surface & Rear Panel	6
Control Surface	6
Rear Panel	10
Analog I/O & Digital I/O	12
Analog Inputs & Outputs	12
Digital Inputs & Outputs	13
Converting Sampling Rates of Signals Received at I/O Card Inputs	14
Monitoring Digital Input Channel Status	14
Dithering Digital Outputs	15
Setting the Transfer Format for Higher Sampling Rates	16
Input Channels	17
About Input Channels	17
Setting the Input Channels from the Display	18
Setting the Input Channels from the Control Surface	25
Pairing Input Channels	26
Naming Input Channels	28
Bus Outs	29
About Stereo Out	29
Bus Out 1–8	29
Setting the Stereo Out and Bus Out 1–8 from the Display	30
Setting the Stereo Out and Bus Out 1–8 from the Control Surface	33
Pairing Buses or Aux Sends	33
Attenuating Output Signals	34
Naming the Stereo Out and Bus Outs	35
Aux Outs	36
Aux Out 1–8	36
Setting Aux Out 1–8 from the Display	36
Setting Aux Out 1–8 from the Control Surface	38
Setting Aux Send Levels	38
Viewing Aux Send Settings for Multiple Channels	40
Panning Aux Sends	41
Copying Channel Fader Positions to Aux Sends	42
Input & Output Patching	43
Input Patching	43
Output Patching	44
Patching Direct Outs	46
Insert Patching	47
Monitoring	49
Monitor	49
Monitor and Solo Setup	49
Using the Monitor	50
Using the Solo Function	51
Surround Pan	52
About Surround Pan	52
Setting Up and Selecting Surround Pan Modes	53
Surround Panning	56
Grouping Channels & Linking Parameters	59
Grouping & Linking	59
Using Fader Groups and Mute Groups	59
Using Fader Group Master	61
Using Mute Group Master	62
Linking EQ and Compressor Parameters	62
Internal Effects	64
About the Internal Effects	64
Using Effects Processors via Aux Sends	64
Inserting the Internal Effects into Channels	65
Editing Effects	66
About Add-On Effects	67
About Plug-Ins	67
Scene Memories	68
About Scene Memories	68
What is Stored in a Scene?	68
About Scene Numbers	68
Storing and Recalling Scenes	69
Auto Scene Memory Update	70
Fading Scenes	71
Recalling Scenes Safely	72
Sorting Scenes	72
Copying and Pasting a Scene (Global Paste)	73
Libraries	74
About the Libraries	74
General Library Operation	74
Using Libraries	75
Remote Control	83
About Remote Function	83
Pro Tools Remote Layer	83
Nuendo/Cubase Remote Layer	93
Other DAW Remote Layer	94
MIDI Remote Layer	94
Machine Control Function	98
MIDI	100
MIDI & the 01V96i	100
MIDI Port Setup	101
Assigning Scenes to Program Changes for Remote Recall	103
Assigning Parameters to Control Changes for Real-time Control	104
Controlling Parameters by Using Parameter Changes	106
Transmitting Parameter Settings via MIDI (Bulk Dump)	107
Other Functions	109
Setting Preferences	109
Creating a Custom Layer by Combining Channels (User Assignable Layer)	110
Cascading Consoles	111
Checking the Battery and the System Version	113
Calibrating the Faders	113
Index	115
Appendix: Parameter Lists	119
USER DEFINED KEYS	119
USER DEFINED KEYS Initial Assignments	121
Input Patch Parameters	121
Initial Input Patch Settings	123
Output Patch Parameters	125
Initial Output Patch Settings	127
User Defined Remote Layer Initial Bank Settings	128
Effects Parameters	132
Effects and tempo synchronization	146
Preset EQ Parameters	147
Preset Gate Parameters (fs = 44.1 kHz)	148
Preset Compressor Parameters (fs = 44.1 kHz)	149
Dynamics Parameters	151
Appendix: MIDI	156
Scene Memory to Program Change Table	156
Initial Parameter to Control Change Table	157
MIDI Data Format	173

Yamaha 01V96i Reference Manual - Page 83

Remote Control, About Remote Function, Pro Tools Remote Layer

Page 83 highlights