Yamaha 01V96i Reference Manual - Page 135

Effects Parameters

135

Appendix: Parameter Lists

01V96i—Reference Manual

PHASER

Two input, two output 16-stage phaser.

AUTO PAN

Two input, two output autopanner.

TREMOLO

Two input, two output tremolo effect

.

HQ. PITCH

One input, two output high-quality pitch shifter

(Available for internal effects 1 and 2.).

DUAL PITCH

Two input, two output pitch shifter.

Parameter

Range

Description

FREQ.

0.05–40.00 Hz

Modulation speed

DEPTH

0–100%

Modulation depth

FB. GAIN

–99 to +99%

Feedback gain (plus values for

normal-phase feedback, minus

values for reverse-phase feed-

back)

OFFSET

0–100

Lowest phase-shifted frequency

offset

PHASE

0.00–354.38

degrees

Left and right modulation phase

balance

STAGE

2, 4, 6, 8, 10, 12,

14, 16

Number of phase shift stages

LSH F

21.2 Hz–8.00 kHz

Low shelving filter frequency

LSH G

–12.0 to +12.0 dB

Low shelving filter gain

HSH F

50.0 Hz–16.0 kHz

High shelving filter frequency

HSH G

–12.0 to +12.0 dB

High shelving filter gain

SYNC

OFF, ON

Tempo parameter sync on/off

NOTE

1

1.

Used in conjunction with TEMPO

to determine FREQ.

Parameter

Range

Description

FREQ.

0.05–40.00 Hz

Modulation speed

DEPTH

0–100%

Modulation depth

DIR.

1

1.

L<->R, L—>R, L<—R, Turn L, Turn R

Panning direction

WAVE

Sine, Tri, Square

Modulation waveform

LSH F

21.2 Hz–8.00 kHz


LSH G

–12.0 to +12.0 dB


EQ F

100 Hz–8.00 kHz

EQ (peaking type) frequency

EQ G

–12.0 to +12.0 dB

EQ (peaking type) gain

EQ Q

10.0–0.10

EQ (peaking type) bandwidth

HSH F

50.0 Hz–16.0 kHz


HSH G

–12.0 to +12.0 dB


SYNC

OFF, ON


NOTE

2

2.


to determine FREQ.

Parameter

Range

Description

FREQ.

0.05–40.00 Hz

Modulation speed

DEPTH

0–100%

Modulation depth

WAVE

Sine, Tri, Square

Modulation waveform

LSH F

21.2 Hz–8.00 kHz


LSH G

–12.0 to +12.0 dB


EQ F

100 Hz–8.00 kHz

EQ (peaking type) frequency

EQ G

–12.0 to +12.0 dB

EQ (peaking type) gain

EQ Q

10.0–0.10

EQ (peaking type) bandwidth

HSH F

50.0 Hz–16.0 kHz


HSH G

–12.0 to +12.0 dB


SYNC

OFF, ON


NOTE

1

1.


to determine FREQ.

Parameter

Range

Description

PITCH

–12 to +12 semi-

tones

Pitch shift

FINE

–50 to +50 cents

Pitch shift fine

DELAY

0.0–1000.0 ms

Delay time

FB. GAIN

–99 to +99%

Feedback gain (plus values for

normal-phase feedback, minus

values for reverse-phase feed-

back)

MODE

1–10

Pitch shift precision

SYNC

OFF, ON


NOTE

1

1.

(Maximum value depends on the tempo setting)


to determine DELAY

Parameter

Range

Description

PITCH 1

–24 to +24 semi-

tones

Channel #1 pitch shift

FINE 1

–50 to +50 cents

Channel #1 pitch shift fine

LEVEL 1

–100 to +100%

Channel #1 level (plus values for

normal phase, minus values for

reverse phase)

PAN 1

L63 to R63

Channel #1 pan

DELAY 1

0.0–1000.0 ms

Channel #1 delay time

FB. G 1

–99 to +99%

Channel #1 feedback gain (plus

values for normal-phase feed-

back, minus values for

reverse-phase feedback)

PITCH 2

–24 to +24 semi-

tones

Channel #2 pitch shift

FINE 2

–50 to +50 cents

Channel #2 pitch shift fine

LEVEL 2

–100 to +100%

Channel #2 level (plus values for

normal phase, minus values for

reverse phase)

PAN 2

L63 to R63

Channel #2 pan

DELAY 2

0.0–1000.0 ms

Channel #2 delay time

FB. G 2

–99 to +99%

Channel #2 feedback gain (plus

values for normal-phase feed-

back, minus values for

reverse-phase feedback)

MODE

1–10

Pitch shift precision

SYNC

OFF, ON


NOTE 1

1

1.

(Maximum value depends on the tempo setting)


to determine Channel #1 delay

NOTE 2

1


to determine Channel #2 delay

Section	Page
How to Use This Reference Manual	1
Contents	2
Contents of the Owner’s Manual (Booklet)	3
Function Tree	4
Control Surface & Rear Panel	6
Control Surface	6
Rear Panel	10
Analog I/O & Digital I/O	12
Analog Inputs & Outputs	12
Digital Inputs & Outputs	13
Converting Sampling Rates of Signals Received at I/O Card Inputs	14
Monitoring Digital Input Channel Status	14
Dithering Digital Outputs	15
Setting the Transfer Format for Higher Sampling Rates	16
Input Channels	17
About Input Channels	17
Setting the Input Channels from the Display	18
Setting the Input Channels from the Control Surface	25
Pairing Input Channels	26
Naming Input Channels	28
Bus Outs	29
About Stereo Out	29
Bus Out 1–8	29
Setting the Stereo Out and Bus Out 1–8 from the Display	30
Setting the Stereo Out and Bus Out 1–8 from the Control Surface	33
Pairing Buses or Aux Sends	33
Attenuating Output Signals	34
Naming the Stereo Out and Bus Outs	35
Aux Outs	36
Aux Out 1–8	36
Setting Aux Out 1–8 from the Display	36
Setting Aux Out 1–8 from the Control Surface	38
Setting Aux Send Levels	38
Viewing Aux Send Settings for Multiple Channels	40
Panning Aux Sends	41
Copying Channel Fader Positions to Aux Sends	42
Input & Output Patching	43
Input Patching	43
Output Patching	44
Patching Direct Outs	46
Insert Patching	47
Monitoring	49
Monitor	49
Monitor and Solo Setup	49
Using the Monitor	50
Using the Solo Function	51
Surround Pan	52
About Surround Pan	52
Setting Up and Selecting Surround Pan Modes	53
Surround Panning	56
Grouping Channels & Linking Parameters	59
Grouping & Linking	59
Using Fader Groups and Mute Groups	59
Using Fader Group Master	61
Using Mute Group Master	62
Linking EQ and Compressor Parameters	62
Internal Effects	64
About the Internal Effects	64
Using Effects Processors via Aux Sends	64
Inserting the Internal Effects into Channels	65
Editing Effects	66
About Add-On Effects	67
About Plug-Ins	67
Scene Memories	68
About Scene Memories	68
What is Stored in a Scene?	68
About Scene Numbers	68
Storing and Recalling Scenes	69
Auto Scene Memory Update	70
Fading Scenes	71
Recalling Scenes Safely	72
Sorting Scenes	72
Copying and Pasting a Scene (Global Paste)	73
Libraries	74
About the Libraries	74
General Library Operation	74
Using Libraries	75
Remote Control	83
About Remote Function	83
Pro Tools Remote Layer	83
Nuendo/Cubase Remote Layer	93
Other DAW Remote Layer	94
MIDI Remote Layer	94
Machine Control Function	98
MIDI	100
MIDI & the 01V96i	100
MIDI Port Setup	101
Assigning Scenes to Program Changes for Remote Recall	103
Assigning Parameters to Control Changes for Real-time Control	104
Controlling Parameters by Using Parameter Changes	106
Transmitting Parameter Settings via MIDI (Bulk Dump)	107
Other Functions	109
Setting Preferences	109
Creating a Custom Layer by Combining Channels (User Assignable Layer)	110
Cascading Consoles	111
Checking the Battery and the System Version	113
Calibrating the Faders	113
Index	115
Appendix: Parameter Lists	119
USER DEFINED KEYS	119
USER DEFINED KEYS Initial Assignments	121
Input Patch Parameters	121
Initial Input Patch Settings	123
Output Patch Parameters	125
Initial Output Patch Settings	127
User Defined Remote Layer Initial Bank Settings	128
Effects Parameters	132
Effects and tempo synchronization	146
Preset EQ Parameters	147
Preset Gate Parameters (fs = 44.1 kHz)	148
Preset Compressor Parameters (fs = 44.1 kHz)	149
Dynamics Parameters	151
Appendix: MIDI	156
Scene Memory to Program Change Table	156
Initial Parameter to Control Change Table	157
MIDI Data Format	173

Yamaha 01V96i Reference Manual - Page 135

PHASER, AUTO PAN, TREMOLO, HQ. PITCH, DUAL PITCH, Two input, two output tremolo effect

Page 135 highlights