Yamaha 01V96i Reference Manual - Page 50

50

Monitoring

01V96i—Reference Manual

3

SEL MODE

This parameter determines how the Input Channels will

be soloed when you press the [SOLO] button of each

Channel. There are two options.

•

MIX SOLO

In Mix Solo mode, any number of channels can be soloed

simultaneously.

•

LAST SOLO

In Last Solo mode, only one channel can be soloed at a

time by pressing the [SOLO] button. The Solo function

that was previously enabled for channels is automatically

cancelled.

4

LISTEN

This parameter determines the source of the Input Chan-

nel Solo signal: Pre Fader or Post Pan. When Pre Fader is

selected, turning on the PAN button below the Pre Fader

option will solo the channel with the pan position speci-

fied by the Pan setting even if the source precedes the

fader. This parameter is effective only in Recording Solo

mode.

5

SOLO TRIM

This parameter enables you to trim the level of the Solo

signal in the range of –96 dB to +12 dB.

6

FADER/SOLO RELEASE

If this check box is checked, you can unsolo the channels

by raising the channel faders that were at the level of –



when the Solo function was turned on. If the faders were

set to higher than –



, the channels cannot be soloed. This

setting is not effective in Mixdown Solo mode and for

Output Channels.

7

SOLO SAFE CHANNEL

For Mixdown Solo mode, Input Channels can be config-

ured individually so that they are not muted when other

Input Channels are soloed (Solo Safe function). Signals

from Input Channels with the SOLO SAFE CHANNEL

button turned on are always fed to the Stereo bus, regard-

less of the channels’ Solo function status. You can clear all

Solo Safe settings by turning on the ALL CLEAR button.

8

MONITOR TRIM

This parameter enables you to trim the level of the mon-

itoring signal in the range of –96 dB to +12 dB.

9

MONO

This button switches the Monitor signal into mono.

Using the Monitor

1.

Connect a monitoring system to the MONI-

TOR OUT connectors.

To monitor the signal via headphones, connect head-

phones to the PHONES jack.

2.

Press the Monitor Source selector in the

MONITOR section to select the monitoring

signal source.

To monitor the 01V96i’s internal signals, turn off the

selector (the button should be raised). To monitor the sig-

nals at the 2TR IN connectors, turn on the selector (the

button should be pushed in).

3.

Adjust the monitoring level using the MONI-

TOR [MONITOR LEVEL] control while playing

the sound sources.

To adjust the level of the monitoring signal via head-

phones, turn the [PHONES LEVEL] control.

Note:

When you check the FADER/SOLO RELEASE check

box, the Solo setting is temporarily cancelled.

Tip:

For example, if you set the internal effects processor’s

return signal to Solo Safe, you can monitor the soloed “pro-

cessed (or wet)” signals.

PHONES

MONITOR

OUT

MONITOR

2TR IN

LEVEL

PHONES

LEVEL

0

10

0

10

Section	Page
How to Use This Reference Manual	1
Contents	2
Contents of the Owner’s Manual (Booklet)	3
Function Tree	4
Control Surface & Rear Panel	6
Control Surface	6
Rear Panel	10
Analog I/O & Digital I/O	12
Analog Inputs & Outputs	12
Digital Inputs & Outputs	13
Converting Sampling Rates of Signals Received at I/O Card Inputs	14
Monitoring Digital Input Channel Status	14
Dithering Digital Outputs	15
Setting the Transfer Format for Higher Sampling Rates	16
Input Channels	17
About Input Channels	17
Setting the Input Channels from the Display	18
Setting the Input Channels from the Control Surface	25
Pairing Input Channels	26
Naming Input Channels	28
Bus Outs	29
About Stereo Out	29
Bus Out 1–8	29
Setting the Stereo Out and Bus Out 1–8 from the Display	30
Setting the Stereo Out and Bus Out 1–8 from the Control Surface	33
Pairing Buses or Aux Sends	33
Attenuating Output Signals	34
Naming the Stereo Out and Bus Outs	35
Aux Outs	36
Aux Out 1–8	36
Setting Aux Out 1–8 from the Display	36
Setting Aux Out 1–8 from the Control Surface	38
Setting Aux Send Levels	38
Viewing Aux Send Settings for Multiple Channels	40
Panning Aux Sends	41
Copying Channel Fader Positions to Aux Sends	42
Input & Output Patching	43
Input Patching	43
Output Patching	44
Patching Direct Outs	46
Insert Patching	47
Monitoring	49
Monitor	49
Monitor and Solo Setup	49
Using the Monitor	50
Using the Solo Function	51
Surround Pan	52
About Surround Pan	52
Setting Up and Selecting Surround Pan Modes	53
Surround Panning	56
Grouping Channels & Linking Parameters	59
Grouping & Linking	59
Using Fader Groups and Mute Groups	59
Using Fader Group Master	61
Using Mute Group Master	62
Linking EQ and Compressor Parameters	62
Internal Effects	64
About the Internal Effects	64
Using Effects Processors via Aux Sends	64
Inserting the Internal Effects into Channels	65
Editing Effects	66
About Add-On Effects	67
About Plug-Ins	67
Scene Memories	68
About Scene Memories	68
What is Stored in a Scene?	68
About Scene Numbers	68
Storing and Recalling Scenes	69
Auto Scene Memory Update	70
Fading Scenes	71
Recalling Scenes Safely	72
Sorting Scenes	72
Copying and Pasting a Scene (Global Paste)	73
Libraries	74
About the Libraries	74
General Library Operation	74
Using Libraries	75
Remote Control	83
About Remote Function	83
Pro Tools Remote Layer	83
Nuendo/Cubase Remote Layer	93
Other DAW Remote Layer	94
MIDI Remote Layer	94
Machine Control Function	98
MIDI	100
MIDI & the 01V96i	100
MIDI Port Setup	101
Assigning Scenes to Program Changes for Remote Recall	103
Assigning Parameters to Control Changes for Real-time Control	104
Controlling Parameters by Using Parameter Changes	106
Transmitting Parameter Settings via MIDI (Bulk Dump)	107
Other Functions	109
Setting Preferences	109
Creating a Custom Layer by Combining Channels (User Assignable Layer)	110
Cascading Consoles	111
Checking the Battery and the System Version	113
Calibrating the Faders	113
Index	115
Appendix: Parameter Lists	119
USER DEFINED KEYS	119
USER DEFINED KEYS Initial Assignments	121
Input Patch Parameters	121
Initial Input Patch Settings	123
Output Patch Parameters	125
Initial Output Patch Settings	127
User Defined Remote Layer Initial Bank Settings	128
Effects Parameters	132
Effects and tempo synchronization	146
Preset EQ Parameters	147
Preset Gate Parameters (fs = 44.1 kHz)	148
Preset Compressor Parameters (fs = 44.1 kHz)	149
Dynamics Parameters	151
Appendix: MIDI	156
Scene Memory to Program Change Table	156
Initial Parameter to Control Change Table	157
MIDI Data Format	173

Yamaha 01V96i Reference Manual - Page 50

Using the Monitor, TOR OUT connectors.

Page 50 highlights