Yamaha 01V96i Reference Manual - Page 16

16

Analog I/O & Digital I/O

01V96i—Reference Manual

Setting the Transfer

Format for Higher

Sampling Rates

To operate the 01V96i at higher sampling frequencies

(88.2 kHz or 96 kHz) and transfer digital audio signals to and

from connected external devices, you must set the data trans-

fer format in accordance with the sampling frequencies sup-

ported by the external devices.

1.

Press the DISPLAY ACCESS [DIO/SETUP] but-

ton repeatedly until the DIO/Setup | Word

Clock page appears.

2.

Select INT88.2k or INT96k as the wordclock

source.

3.

Press the DISPLAY ACCESS [DIO/SETUP] but-

ton repeatedly until the DIO/Setup | Format

page appears.

4.

Use the cursor buttons to move the cursor to

an IN/OUT parameter field (

1

), then rotate

the Parameter wheel or press the [INC]/[DEC]

buttons to set the data transfer format.

The IN/OUT parameters are used to set one of the follow-

ing data transfer formats for each slot input and output.

•

DOUBLE CHANNEL

In Double Channel mode, digital audio data is received

and transmitted as mono signals at a sampling rate that is

exactly half (44.1/48 kHz) the current higher sampling

rate. Data is handled by two channels. This is useful when

you want to transfer data between the 01V96i operating at

a higher sampling rate and an external digital device that

supports 44.1/48 kHz.

•

DOUBLE SPEED

In Double Speed mode, digital audio data is received and

transmitted at the current high sampling rate (i.e.,

88.2 kHz or 96 kHz). Select this mode if the devices that

support the higher sampling rates transmit or receive

data.

• SINGLE

In Single mode, digital audio data is received and trans-

mitted at a sampling rate that is half (44.1/48 kHz) the

current higher sampling rate of the 01V96i. For example,

this is useful when you want to receive 44.1 kHz digital

signals from an external digital device while the 01V96i is

operating at 88.2 kHz.

Note:

When the 01V96i operates at a high sampling rate

(88.2

kHz or 96

kHz), only two internal effects processors are

available.

Note:

Double Channel mode reduces the total number of

inputs or outputs on the corresponding slot. The even-num-

bered channels are disabled.

1

Note:

You can select this setting only for slots in which a dig-

ital I/O card that inputs/outputs double-speed digital audio

data (e.g., MY8-AE96, MY8-AE96S) is installed.

Note:

You cannot select this setting for slots in which a digital

I/O card that inputs/outputs double-speed digital audio data

(e.g., MY8-AE96, MY8-AE96S) is installed.

Tip:

The parameter fields display “–” if the slot contains no

I/O card or if an AD/DA card or other I/O card that does not

allow you to set the transfer format has been installed.

Section	Page
How to Use This Reference Manual	1
Contents	2
Contents of the Owner’s Manual (Booklet)	3
Function Tree	4
Control Surface & Rear Panel	6
Control Surface	6
Rear Panel	10
Analog I/O & Digital I/O	12
Analog Inputs & Outputs	12
Digital Inputs & Outputs	13
Converting Sampling Rates of Signals Received at I/O Card Inputs	14
Monitoring Digital Input Channel Status	14
Dithering Digital Outputs	15
Setting the Transfer Format for Higher Sampling Rates	16
Input Channels	17
About Input Channels	17
Setting the Input Channels from the Display	18
Setting the Input Channels from the Control Surface	25
Pairing Input Channels	26
Naming Input Channels	28
Bus Outs	29
About Stereo Out	29
Bus Out 1–8	29
Setting the Stereo Out and Bus Out 1–8 from the Display	30
Setting the Stereo Out and Bus Out 1–8 from the Control Surface	33
Pairing Buses or Aux Sends	33
Attenuating Output Signals	34
Naming the Stereo Out and Bus Outs	35
Aux Outs	36
Aux Out 1–8	36
Setting Aux Out 1–8 from the Display	36
Setting Aux Out 1–8 from the Control Surface	38
Setting Aux Send Levels	38
Viewing Aux Send Settings for Multiple Channels	40
Panning Aux Sends	41
Copying Channel Fader Positions to Aux Sends	42
Input & Output Patching	43
Input Patching	43
Output Patching	44
Patching Direct Outs	46
Insert Patching	47
Monitoring	49
Monitor	49
Monitor and Solo Setup	49
Using the Monitor	50
Using the Solo Function	51
Surround Pan	52
About Surround Pan	52
Setting Up and Selecting Surround Pan Modes	53
Surround Panning	56
Grouping Channels & Linking Parameters	59
Grouping & Linking	59
Using Fader Groups and Mute Groups	59
Using Fader Group Master	61
Using Mute Group Master	62
Linking EQ and Compressor Parameters	62
Internal Effects	64
About the Internal Effects	64
Using Effects Processors via Aux Sends	64
Inserting the Internal Effects into Channels	65
Editing Effects	66
About Add-On Effects	67
About Plug-Ins	67
Scene Memories	68
About Scene Memories	68
What is Stored in a Scene?	68
About Scene Numbers	68
Storing and Recalling Scenes	69
Auto Scene Memory Update	70
Fading Scenes	71
Recalling Scenes Safely	72
Sorting Scenes	72
Copying and Pasting a Scene (Global Paste)	73
Libraries	74
About the Libraries	74
General Library Operation	74
Using Libraries	75
Remote Control	83
About Remote Function	83
Pro Tools Remote Layer	83
Nuendo/Cubase Remote Layer	93
Other DAW Remote Layer	94
MIDI Remote Layer	94
Machine Control Function	98
MIDI	100
MIDI & the 01V96i	100
MIDI Port Setup	101
Assigning Scenes to Program Changes for Remote Recall	103
Assigning Parameters to Control Changes for Real-time Control	104
Controlling Parameters by Using Parameter Changes	106
Transmitting Parameter Settings via MIDI (Bulk Dump)	107
Other Functions	109
Setting Preferences	109
Creating a Custom Layer by Combining Channels (User Assignable Layer)	110
Cascading Consoles	111
Checking the Battery and the System Version	113
Calibrating the Faders	113
Index	115
Appendix: Parameter Lists	119
USER DEFINED KEYS	119
USER DEFINED KEYS Initial Assignments	121
Input Patch Parameters	121
Initial Input Patch Settings	123
Output Patch Parameters	125
Initial Output Patch Settings	127
User Defined Remote Layer Initial Bank Settings	128
Effects Parameters	132
Effects and tempo synchronization	146
Preset EQ Parameters	147
Preset Gate Parameters (fs = 44.1 kHz)	148
Preset Compressor Parameters (fs = 44.1 kHz)	149
Dynamics Parameters	151
Appendix: MIDI	156
Scene Memory to Program Change Table	156
Initial Parameter to Control Change Table	157
MIDI Data Format	173

Yamaha 01V96i Reference Manual - Page 16

Setting the Transfer Format for Higher Sampling Rates

Page 16 highlights