Home » Yamaha Manuals » Audio Mixers » Yamaha 01V96i » Manual Viewer

Yamaha 01V96i Reference Manual - Page 113

Checking the Battery and the System Version, Calibrating the Faders - firmware

Get Yamaha 01V96i PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 113 highlights

Other Functions Checking the Battery and the System Version 113 Checking the Battery and the System Version The Utility | Battery page enables you to check the condition of the internal memory-backup battery and the system version number. To locate this page, press the DISPLAY ACCESS [UTILITY] button repeatedly. 1 Calibrating the Faders The 01V96i motorized fader positions may shift over time depending on the operating conditions and environment. You can correct the shifted faders using the Calibration function. 1. Make sure that the power to the 01V96i is turned off. 2. Press and hold down the [ENTER] button, then turn on the POWER ON/OFF switch. After a while, the following calibration window appears. 2 1 Status If the Status is "Okay," the battery has sufficient voltage for operation. If the Status is "Voltage Low!," ask your Yamaha dealer or authorized Yamaha service center to replace the battery as soon as possible. Failure to replace a low battery may result in data loss. Note: Do not attempt to replace the battery yourself as a malfunction may occur. 2 Ver X.XX (X.XX represents the version number.) This indicator identifies the system version number. Check the current system version number before you update the firmware. Visit the following website to check the latest system version number: http://www.yamahaproaudio.com/ 3. Make sure that "1 FADER MOVE & FADER POSITION" is selected, then press [ENTER]. To adjust only the motor fader movement, use the cursor buttons to select "2 FADER MOVE ONLY," then press [ENTER]. To adjust only the fader position, use the cursor buttons to select "3 FADER POSITION ONLY," then press [ENTER]. Proceed to Step 5. To cancel the calibration operation, use the cursor buttons to select "4 QUIT," then press [ENTER]. The 01V96i starts in normal mode. 4. The calibration operation begins, adjusting the motor fader movement, and the 01V96i displays a message that indicates the calibration operation is in progress. The calibration operation takes about two minutes. DO NOT touch the faders during the operation. 01V96i-Reference Manual

Section	Page
How to Use This Reference Manual	1
Contents	2
Contents of the Owner’s Manual (Booklet)	3
Function Tree	4
Control Surface & Rear Panel	6
Control Surface	6
Rear Panel	10
Analog I/O & Digital I/O	12
Analog Inputs & Outputs	12
Digital Inputs & Outputs	13
Converting Sampling Rates of Signals Received at I/O Card Inputs	14
Monitoring Digital Input Channel Status	14
Dithering Digital Outputs	15
Setting the Transfer Format for Higher Sampling Rates	16
Input Channels	17
About Input Channels	17
Setting the Input Channels from the Display	18
Setting the Input Channels from the Control Surface	25
Pairing Input Channels	26
Naming Input Channels	28
Bus Outs	29
About Stereo Out	29
Bus Out 1–8	29
Setting the Stereo Out and Bus Out 1–8 from the Display	30
Setting the Stereo Out and Bus Out 1–8 from the Control Surface	33
Pairing Buses or Aux Sends	33
Attenuating Output Signals	34
Naming the Stereo Out and Bus Outs	35
Aux Outs	36
Aux Out 1–8	36
Setting Aux Out 1–8 from the Display	36
Setting Aux Out 1–8 from the Control Surface	38
Setting Aux Send Levels	38
Viewing Aux Send Settings for Multiple Channels	40
Panning Aux Sends	41
Copying Channel Fader Positions to Aux Sends	42
Input & Output Patching	43
Input Patching	43
Output Patching	44
Patching Direct Outs	46
Insert Patching	47
Monitoring	49
Monitor	49
Monitor and Solo Setup	49
Using the Monitor	50
Using the Solo Function	51
Surround Pan	52
About Surround Pan	52
Setting Up and Selecting Surround Pan Modes	53
Surround Panning	56
Grouping Channels & Linking Parameters	59
Grouping & Linking	59
Using Fader Groups and Mute Groups	59
Using Fader Group Master	61
Using Mute Group Master	62
Linking EQ and Compressor Parameters	62
Internal Effects	64
About the Internal Effects	64
Using Effects Processors via Aux Sends	64
Inserting the Internal Effects into Channels	65
Editing Effects	66
About Add-On Effects	67
About Plug-Ins	67
Scene Memories	68
About Scene Memories	68
What is Stored in a Scene?	68
About Scene Numbers	68
Storing and Recalling Scenes	69
Auto Scene Memory Update	70
Fading Scenes	71
Recalling Scenes Safely	72
Sorting Scenes	72
Copying and Pasting a Scene (Global Paste)	73
Libraries	74
About the Libraries	74
General Library Operation	74
Using Libraries	75
Remote Control	83
About Remote Function	83
Pro Tools Remote Layer	83
Nuendo/Cubase Remote Layer	93
Other DAW Remote Layer	94
MIDI Remote Layer	94
Machine Control Function	98
MIDI	100
MIDI & the 01V96i	100
MIDI Port Setup	101
Assigning Scenes to Program Changes for Remote Recall	103
Assigning Parameters to Control Changes for Real-time Control	104
Controlling Parameters by Using Parameter Changes	106
Transmitting Parameter Settings via MIDI (Bulk Dump)	107
Other Functions	109
Setting Preferences	109
Creating a Custom Layer by Combining Channels (User Assignable Layer)	110
Cascading Consoles	111
Checking the Battery and the System Version	113
Calibrating the Faders	113
Index	115
Appendix: Parameter Lists	119
USER DEFINED KEYS	119
USER DEFINED KEYS Initial Assignments	121
Input Patch Parameters	121
Initial Input Patch Settings	123
Output Patch Parameters	125
Initial Output Patch Settings	127
User Defined Remote Layer Initial Bank Settings	128
Effects Parameters	132
Effects and tempo synchronization	146
Preset EQ Parameters	147
Preset Gate Parameters (fs = 44.1 kHz)	148
Preset Compressor Parameters (fs = 44.1 kHz)	149
Dynamics Parameters	151
Appendix: MIDI	156
Scene Memory to Program Change Table	156
Initial Parameter to Control Change Table	157
MIDI Data Format	173

Match case Limit results 1 per page

Checking the Battery and the System Version

113

01V96i—Reference Manual

Other Functions

Checking the Battery and

the System Version

The Utility | Battery page enables you to check the condition

of the internal memory-backup battery and the system ver-

sion number. To locate this page, press the DISPLAY ACCESS

[UTILITY] button repeatedly.

Status

If the Status is “Okay,” the battery has sufficient voltage for

operation. If the Status is “Voltage Low!,” ask your

Yamaha dealer or authorized Yamaha service center to

replace the battery as soon as possible. Failure to replace

a low battery may result in data loss.

Ver X.XX (X.XX represents the version number.)

This indicator identifies the system version number.

Check the current system version number before you

update the firmware.

Visit the following website to check the latest system ver-

sion number:

http://www.yamahaproaudio.com/

Calibrating the Faders

The 01V96i motorized fader positions may shift over time

depending on the operating conditions and environment.

You can correct the shifted faders using the Calibration func-

tion.

Make sure that the power to the 01V96i is

turned off.

Press and hold down the [ENTER] button,

then turn on the POWER ON/OFF switch.

After a while, the following calibration window appears.

Make sure that “1 FADER MOVE & FADER

POSITION” is selected, then press [ENTER].

To adjust only the motor fader movement, use the cursor

buttons to select “2 FADER MOVE ONLY,” then press

[ENTER].

To adjust only the fader position, use the cursor buttons

to select “3 FADER POSITION ONLY,” then press

[ENTER]. Proceed to Step 5.

To cancel the calibration operation, use the cursor but-

tons to select “4 QUIT,” then press [ENTER]. The 01V96i

starts in normal mode.

The calibration operation begins, adjusting

the motor fader movement, and the 01V96i

displays a message that indicates the calibra-

tion operation is in progress.

The calibration operation takes about two minutes. DO

NOT touch the faders during the operation.

Note:

Do not attempt to replace the battery yourself as a mal-

function may occur.