Yamaha 01V96i Reference Manual - Page 29

Bus Outs Bus Outs 29 STEREO L STEREO R BUS1 BUS2 BUS3 BUS4 BUS5 BUS6 BUS7 BUS8 STEREO L STEREO R OUTPUT PATCH Bus Outs This chapter describes how to adjust the 01V96i's Stereo Out and Bus Out 1-8 parameters. About Stereo Out The Stereo Out section receives Input Channel and Bus Out 1-8 signals, mixes them into two channels, processes them using on-board EQ, compressor, etc., then routes them to the STEREO OUT and 2TR OUT connectors. The following diagram illustrates the Stereo Out signal flow. (Gain Reduction) (Out Meter) METER METER COMP INSERT ATT METER 4BAND EQ INSERT ON INSERT LEVEL BAL OUTPUT DELAY METER DA Same as stereo master L DA L (-10dBV) [2TR OUT] R L (+4dBu) [STEREO OUT] R OUTPUT PATCH • INSERT This section enables you to route the Stereo Out signals to external devices via the on-board connectors or I/O card, or insert internal effects processors. • ATT (Attenuator) This section enables you to attenuate or amplify the level of signals to be input to the EQ. The attenuator prevents post-EQ signals from clipping or corrects signal levels that are too low. • 4 BAND EQ (4-band equalizer) This parametric EQ features four bands (HIGH, HIGH-MID, LOW-MID, and LOW). • COMP (Compressor) This dynamics processor can be used as compressor, expander, or limiter. The processor can be located pre-EQ, pre-[STEREO] fader, or post-[STEREO] fader. • ON (On/Off) This button turns the Stereo Out on or off. • LEVEL The [STEREO] fader adjusts the Stereo Out output levels. • Balance This section enables you to adjust the level balance between the L and R channels of the Stereo Out. • OUTPUT DELAY (Output delay) This section delays the output signals. It is mainly used to fine-tune the signal timing. • METER This section enables you to switch the metering position of signal levels that are displayed on the Meter page or by the stereo meter to the right of the screen. For more information on selecting the metering position, refer to "Viewing the Level Meters" in the Owner's Manual (booklet). Note: You can also patch the Stereo Out signals to other output connectors or the I/O card by using the Patch | Out Patch pages. Bus Out 1-8 The Bus Out 1-8 section mixes signals routed from Input Channels to the specified buses, processes them using on-board EQ, compressor, etc., then routes them to the specified output connectors or I/O card. The following diagram illustrates the Bus Out signal flow. (Gain Reduction) (Out Meter) METER METER COMP INSERT ATT METER 4BAND EQ INSERT ON INSERT LEVEL OUTPUT DELAY METER ON LEVEL PAN BUS to STEREO BUS 1(...8) • INSERT • ATT (Attenuator) • 4 BAND EQ (4-band equalizer) • COMP (Compressor) • ON (On/Off) • LEVEL • OUTPUT DELAY (Output delay) • METER The parameters and sections listed above are identical to those for the Stereo Out. For more information, refer to the explanation of the Stereo Out. • Bus to Stereo Bus Out 1-8 signals are also routed to the Stereo Bus. In addition to the ON, LEVEL, and other parameters, you can also set the Send Level, On/Off, Pan, and other parameters. Tip: • You can also pair adjacent odd-even buses for stereo operation (see page 33). • By default, Slot channels 1-8 and 9-16 and ADAT OUT chan- nels 1-8 are patched to the Bus Out 1-8 outputs. However, you can change this patching on the Patch | Out Patch page (see page 44). 01V96i-Reference Manual