Netgear GSM7252PS ProSafe Managed Switch Web Management User Manual
Netgear GSM7252PS - ProSafe 52 Ports Gigabit Ethernet L2 Managed Stackable Switch Manual
UPC - 606449071665
View all Netgear GSM7252PS manuals
Add to My Manuals
Save this manual to your list of manuals |
Netgear GSM7252PS manual content summary:
- Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 1
ProSafe® Managed Switch Web Management User Manual 350 East Plumeria Drive San Jose, CA 95134 USA October 27, 2010 202-10757-01 v1.0 - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 2
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual ©2010 NETGEAR, Inc. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 3
Naming Convention 18 Chapter 2 Configuring System Information Management 19 System Information 20 Switch Statistics 26 System Resource 29 Services 50 DHCP Server 51 DHCP Relay 62 DHCP L2 Relay 64 UDP Relay 67 DHCPv6 Server 71 DHCPv6 Relay 79 Stacking 79 Basic 80 Advanced 83 PoE - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 4
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual LLDP-MED 113 ISDP 121 Basic 121 Advanced 124 Chapter 3 Configuring Switching Information VLANs 130 Basic 131 Advanced 134 Spanning Tree Protocol 151 Basic 152 Advanced 155 Multicast 168 MFDB 168 IGMP Snooping - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 5
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Advanced 268 OSPFv3 296 Basic 296 Advanced 298 Router Discovery 323 Router Discovery Configuration 324 VRRP 325 Basic 325 Advanced 329 Multicast 334 Mroute Table 335 Multicast Global Configuration 336 Multicast - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 6
® Gigabit L3 Managed Stackable Switches Software Administration Manual HTTPS 453 SSH 458 Telnet 462 Console Port 464 Denial of Service 465 Port Authentication 466 Basic 467 Advanced 470 Traffic Control 481 MAC Filter 481 Port Security 484 Private Group 490 Protected Ports Configuration - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 7
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Reset 580 Device Reboot 580 Factory Default 582 Password Reset 583 Upload File From Switch 583 File Upload 583 HTTP File Upload 586 USB File Upload 587 Download File To Switch 587 File Download 588 HTTP File - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 8
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Index 8 | Contents - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 9
field. You must be able to ping the IP address of the ProSafe® Managed Switches management interface from your administrative system for Web access to be available. If you did not change the IP address of the switch from the default value, enter 169.254.100.100 into the address field. Accessing the - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 10
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Understanding the User Interfaces ProSafe® Managed Switches software includes a set of comprehensive management functions for configuring IP address of the switch in the Web browser address field. 10 | Chapter 1. - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 11
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 2. The default username is admin, default password is none (no password). Type the username into the field on the login screen and then click Login. Usernames and passwords are case sensitive. 3. After the system - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 12
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Navigation Tabs, Feature Links, and Page Menu The navigation tabs along the top of the Web interface give you quick access to the various switch tab that is selected. The configuration pages for each feature are available - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 13
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Configuration and Monitoring Options The area directly under the feature links and to the right of the page menu displays the configuration information or status for the page you select. On pages that contain - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 14
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Device View The Device View is a Java® applet that displays the ports on the switch. This graphic provides an alternate way to navigate to configuration and monitoring options. The graphic also provides information about - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 15
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Click the port you want to view or configure to see a menu that displays statistics and configuration options. Click the menu option to access the page that contains the configuration or monitoring options. Chapter 1. - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 16
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual If you click the graphic, but do not click a specific port contains information to assist in configuring and managing the switch. The online help pages are context sensitive. For example, if the IP Addressing page is open, - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 17
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual User-Defined Fields User-defined fields can contain 1 to 159 characters, unless otherwise noted on the configuration Web page. All characters may be used except for the following (unless specifically noted in for that - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 18
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Interface Naming Convention The ProSafe® Managed Switches support physical and logical interfaces. Interfaces are identified by their type and the interface number. The physical ports are gigabit interfaces and are - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 19
on page 49 • Services on page 50 • Stacking on page 79 • PoE on page 86 • SNMP on page 93 • LLDP on page 102 • ISDP on page 121 Management This section describes how to display the switch status and specify some basic switch information, such as the management interface IP address, system clock - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 20
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual System Information After a successful login, the System Information page displays. Use this page to configure and view general device information. To display the System Information page, click System Management System - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 21
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual The System Information provides various statuses: Switch Status To define system information: 1. Open the System Information page. 2. Define the following fields: a. System Name - Enter the name you want to use to identify - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 22
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual The following table describes the status information the Up time System SNMP OID System Mac Address Supported Java Plugin Version Description The product name of this switch. The IPv4 address and mask assigned to the - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 23
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual FAN Status The screen shows the status of the fans in all units. These fans depends on the actual hardware. The following table describes the Temperature Status information. Chapter 2. Configuring System Information | 23 - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 24
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 2-3. Field Description CPU MAC The current temperature of the CPU in the switch. The current temperature of the MACs in the switch. Click REFRESH to refresh the system information of the switch. Device Status - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 25
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 2-4. Field Description RPS Indicates the status of the RPS. The status has three possible values: • Not Present: RPS bank not connected • OK: RPS bank - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 26
® Gigabit L3 Managed Stackable Switches Software Administration Manual Switch Statistics Use this page to display the switch statistics. To display the Switch Statistics page, click System > Management > Switch Statistics. A screen similar to the following displays. 26 | Chapter 2. Configuring - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 27
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual The following table describes Switch Statistics information. Table 2-5. Field ifIndex Octets Received the Broadcast address, including those that were discarded or not sent. Chapter 2. Configuring System Information | 27 - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 28
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table switch were last cleared. Click CLEAR to clear all the counters, resetting all switch summary and detailed statistics to default values. The discarded packets count cannot be cleared. 28 | Chapter 2. Configuring - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 29
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual System Resource Use this page to display the system resources. To display the System Resource page, click System > Management > System Resource. A screen similar to the following displays. CPU Memory Status The following - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 30
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Slot Information Use this page to display slot information and supported cards. To display the Slot Information page, click System > Management > Slot Information. A screen similar to the following displays. Slot Summary - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 31
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Supported Cards The following table displays Supported Cards information. Table 2-8. Field Card Model Card Index Card Type Card Descriptor Description Displays the list of models of all cards that can be supported. - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 32
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Loopback Interface Use this page to create, configure, and remove Loopback interfaces. To display the Loopback Interface page, click System > Management the Secondary IP Address field to input the secondary IP address for - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 33
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Network Interface From the Network Interface link, you can access the following pages: • IPv4 Network Configuration on page 33 • IPv6 Network Configuration on page 35n • IPv6 Network Neighbor on page 37 IPv4 Network - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 34
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Once you have established in-band connectivity, you can change the IP information using any of the following: • Terminal interface via the EIA-232 port • Terminal interface via telnet • SNMP-based management • Web-based - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 35
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IPv6 Network Configuration To display the IPv6 Network Configuration page, click System > Management > Network Interface > IPv6 Network Configuration. A screen similar to the following displays. The IPv6 network interface - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 36
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 1. Use Admin Mode to enable or disable the IPv6 network interface on the switch. The default value is enable. 2. Use IPv6 Address Auto Configuration Mode to set the IPv6 address for the IPv6 network interface in auto - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 37
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IPv6 Network Neighbor Use this page to display IPv6 Network Port Neighbor entries. To display the IPv6 Network Neighbor page, click System > Management > Network Interface > IPv6 Network Neighbor. A screen similar to the - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 38
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Time ProSafe® Managed Switches software supports the Simple Network Time Protocol (SNTP). You can also set the system time manually for which the IP address is known. SNTP servers that have been configured on the device - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 39
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual SNTP Global Configuration Use the SNTP Global Configuration page to view and adjust date and time settings. To display the SNTP Global Configuration page, click System Management > Time SNTP Global Configuration. SNTP - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 40
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Default value is Disable. 2. Use Port to specify the local UDP port to listen for responses/broadcasts. Allowed range is 1 to 65535. Default value is 123. 3. Use Unicast Poll Interval to specify the number of seconds - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 41
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual SNTP Global Status The following table displays SNTP Global Status information. Table 2-11. Field Version Supported Mode Last Update Time Last Attempt Time Last Attempt Status Server IP Address Address Type Server - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 42
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 2-11. Field Server Mode Unicast Server of unicast server entries that can be configured on this client. Specifies the number of current valid unicast server entries configured for this client. Specifies the number - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 43
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual SNTP Server Configuration Use the SNTP Server Configuration page to view and modify information for adding and modifying Simple Network Time Protocol SNTP servers. To display the SNTP Server Configuration page, click - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 44
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 3. Repeat the previous steps to add additional SNTP servers. You can configure up to three SNTP servers. 4. To removing an SNTP server, select the check box next to the configured server to remove, and then click Delete. - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 45
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual SNTP Server Status The SNTP Server Status table displays status information about the SNTP servers configured on your switch operation was successful and the system time was updated. • Request Timed Out - A directed SNTP - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 46
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual DNS You can use these pages to configure information about DNS servers the network uses and how the switch operates as a DNS client. DNS Configuration Use this page to configure global DNS settings and DNS server - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 47
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 6. To remove a DNS server from the the configuration on the screen and reset the data on the screen to the latest value of the switch. 8. Click Apply to send the updated configuration to the switch. Configuration changes - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 48
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Host Configuration Use this page to manually map host names to IP addresses or to view dynamic DNS mappings. To access this page, click System Management DNS Host Configuration. To add a static entry to the local DNS - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 49
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual The Dynamic Host Mapping table shows host name-to-IP address entries that the switch has learned. The following table describes the dynamic host fields. Table 2-14. Field Host Total Elapsed Type Addresses Description - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 50
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual be allowed to configure this functionality. Available License Key allows user to configure Displays list of features that require licensing. Services From the Services link, you can access the following pages: - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 51
® Gigabit L3 Managed Stackable Switches Software Administration Manual • DHCP Relay on page 62 • DHCP L2 Relay on page 64 • UDP Relay on page 67 • DHCPv6 Server on page 71 • DHCPv6 Relay on page 79 DHCP Server From the DHCP Server link, you can access the following pages: • DHCP Server Configuration - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 52
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual DHCP Server Configuration To display the DHCP Server Configuration page, click System > Services > DHCP Server> DHCP Server Configuration. A screen similar to the following displays. To enable or disable DHCP service: 1. - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 53
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Excluded Address Configuration 1. Use the IP Range From field to specify the low address if you want to exclude a range of addresses. Specify the address to be excluded in case you - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 54
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual DHCP Pool Configuration To display the DHCP Pool Configuration page, click System > Services > DHCP Server> DHCP Pool Configuration. A screen similar to the following displays. The following table describes the DHCP Pool - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 55
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual pool. Either Network Mask or Prefix Length can be configured to specify the subnet mask but not both. Default value is ethernet. Specifies the Client Identifier for DHCP manual Pool. Specifies the IP address for a manual - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 56
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 2-17. Field Description Days Specifies the Number of Days of Lease Period. This field appears only if the user has specified "Specified Duration" as the Lease time. Default Value is 1. Valid Range is (0 to 59) - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 57
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual DHCP Pool Options To display the DHCP Pool Options page, click System > Services Code configured for the selected pool: • ASCII • Hex • IP Address 4. Option Value specifies the Value against the Option Code configured for - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 58
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual DHCP Server Statistics To display the DHCP Server Statistics page, click System > Services > DHCP Server> DHCP Server Statistics. A screen similar to the following displays. 58 | Chapter 2. Configuring System Information - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 59
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual The following table describes the DHCP Server Statistics fields. Table 2-18. Field Automatic DHCP Server. Specifies the number of DHCPNAK messages sent by the DHCP Server. Chapter 2. Configuring System Information | 59 - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 60
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual DHCP Bindings Information To display the DHCP Bindings Information page, click System > Services > DHCP Server> DHCP Bindings Information. A screen similar to the following displays. 1. Choose: • All Dynamic Bindings to - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 61
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual DHCP Conflicts Information To display the DHCP Conflicts Information page, click System > Services > DHCP Server> DHCP Conflicts Information. A screen similar to the following displays. 1. Choose: • All Address Conflicts - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 62
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual DHCP Relay To display the DHCP Relay page, click System > Services> DHCP Relay. A screen similar to the following displays. DHCP Relay Configuration 1. Use Maximum Hop Count to enter the maximum number of hops a client - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 63
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual DHCP Relay Status The following table clients since the last time the switch was reset. The total number of DHCP requests forwarded to the server since the last time the switch was reset. The total number of DHCP - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 64
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual DHCP L2 Relay From the DHCP L2 Relay link, you can access the following pages: • DHCP L2 Relay Global Configuration on page 64 • DHCP L2 Relay Interface Configuration on page 65 • DHCP L2 Relay Interface Statistics on page - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 65
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual DHCP L2 Relay Interface Configuration To display the DHCP L2 Relay Interface Configuration page, click System > Services > DHCP L2 Relay> DHCP L2 Relay Interface Configuration. A screen similar to the following displays. - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 66
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual DHCP L2 Relay Interface Statistics To display the DHCP L2 Relay Interface Statistics page, click System > Services > message without option82 received from a trusted client. 66 | Chapter 2. Configuring System Information - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 67
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual UDP Relay From the UDP Relay link, you can access the following pages: • UDP Relay Global Configuration on page 67 • UDP Relay Interface Configuration on page 69 UDP Relay Global Configuration To display the UDP Relay - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 68
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual • tftp - Relay TFTP (UDP port 69) packets • time - Relay time service (UDP port 37) packets • Other - If this option is selected, the UDP Port Other Value is enabled. This option permits a user to enter their own UDP port - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 69
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual UDP Relay Interface Configuration To display the UDP Relay Interface Configuration page, click System > Services > UDP Relay> UDP Relay Interface Configuration. A screen similar to the following displays. 1. Use Interface - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 70
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 5. Use Discard to enable/disable dropping of matched packets. Enable can be chosen only when a user enters 0.0.0.0 IP address. Discard mode can be set to Disable when user adds a new entry with a non-zero IP address. 6. - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 71
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual DHCPv6 Server From the DHCPv6 Server link, you can access the following pages: • DHCPv6 Server Configuration on page 71 • DHCPv6 Pool Configuration on page 72 • DHCPv6 Prefix Delegation Configuration on page 73 • DHCPv6 - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 72
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual DHCPv6 Pool Configuration To display the DHCPv6 Pool Configuration page, click System > Services > DHCPv6 Server> DHCPv6 Pool Configuration. A screen similar to the following displays. 1. Pool Name - For a user with read/ - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 73
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual DHCPv6 Prefix Delegation Configuration To display the DHCPv6 Prefix Delegation Configuration page, click System > Services > DHCPv6 Server> DHCPv6 Prefix Delegation Configuration. A screen similar to the following displays - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 74
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 1. Use Pool Name to select one DHCPv6 pool to be configured. 2. Use Prefix/Prefix Length to specify the delegated IPv6 prefix. 3. Use DUID to identify the client's unique duid value. The format is xx:xx:xx: - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 75
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual DHCPv6 Interface Configuration To display the DHCPv6 Prefix Delegation Configuration page, click System > Services > DHCPv6 Server> DHCPv6 Interface Configuration. A screen similar to the following displays. 1. Use - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 76
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual DHCPv6 Bindings Information To display the DHCPv6 Bindings Information page, click System > Services > DHCPv6 Server> value in seconds of the prefix associated with a binding. 76 | Chapter 2. Configuring System Information - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 77
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual DHCPv6 Server Statistics To display the DHCPv6 Server Statistics page, click System > Services > DHCPv6 Server> DHCPv6 Server Statistics. A screen similar to the following displays. 1. Use Interface to select the interface - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 78
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual The following table describes the DHCPv6 Server Statistics fields. Table 2-26. Field Messages Specifies the number of Relay forwards. Specifies the number of Relay Replies. 78 | Chapter 2. Configuring System Information - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 79
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual DHCPv6 Relay To display the DHCPv6 Relay page, click System > Services > DHCPv6 Relay. A screen similar to the following displays. 1. Use Interface to specify interface configured for DHCPv6 Relay functionality. 2. Use - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 80
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Basic From the Basic link, you can access the following pages: • Stack Configuration on page 80 Stack Configuration This page moves the Primary Management Unit functionality from one unit to another. Upon execution, the - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 81
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual To display the Stack Configuration page, click System > Stacking > Basic> Stack Configuration. A screen similar to the following displays. 1. Use Management Unit Selected to select the unit to be managed unit and click - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 82
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual The following table describes the Stack Configuration fields. Table 2-27. Field Description Hardware Management Preference The hardware management preference of the switch. The hardware management preference can be - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 83
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Advanced From the Advanced link, you can access the following pages: • Stack Configuration on page 80 • Stack Port Configuration on page 85 • Stack Port Diagnostics on page 86 Stack Configuration This page moves the - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 84
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual The following table describes the Stack Configuration fields. Table 2-29. Field Hardware Management Preference Switch Status Management Status Description The hardware management preference of the switch. The hardware - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 85
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Stack Port Configuration To display the Stack Port Configuration page, click System > Stacking > Advanced> Stack Port Configuration. A screen similar to the following displays. 1. Configured Stack Mode - Specify the - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 86
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Stack Port Diagnostics This page displays the diagnostics for all the stackable interfaces in the given stack. To display the Stack Port Diagnostics page, click System > Stacking > Advanced> Stack Port Diagnostics. A - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 87
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual PoE Configuration Use the PoE Configuration page to view global PoE power information and to configure PoE SNMP trap settings. To display this page, click System PoE Basic PoE Configuration. A screen similar to the - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 88
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 3. Field Total Power (Main AC) Total Power (RPS) Power Source Threshold Power Consumed Power Definition Maximum amount of power the system can deliver to all ports when the PoE unit is powered up by Main AC Supply. - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 89
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Advanced From the Advanced link, you can access the following pages: • PoE Configuration on page 89 • PoE Port Configuration on page 91 PoE Configuration Use the PoE Configuration page to view global PoE power information - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 90
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 4. Field Firmware Version Power Status Total Power (Main AC) Total Power (RPS) Power Source Threshold Power Consumed Power Definition Version of the PoE controller's firmware image. Indicates the power status. - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 91
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual PoE Port Configuration Use the PoE Port Configuration page to configure per-port PoE settings. To display this page, click System PoE Advanced PoE Port Configuration. A screen similar to the following displays. 1. - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 92
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 5. Use Power Limit Type to describe or control the maximum power that a port can deliver. "Dot3AF" value means that the port power limit is equal to the dot3af class of the PD attached. "User" value means that the port - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 93
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 5. Field Status Fault Status Definition Operational status of the port pages under the SNMPV1/V2 menu allow you to configure SNMP community information, traps, and trap flags. From the SNMP V1/V2 link, - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 94
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Community Configuration By default, two SNMP Communities exist: • Private, with Read/Write privileges and status set to Enable. • Public, with Read Only privileges and status set to Enable. These - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 95
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual To display this page, click System SNMP SNMP V1/V2 Community Configuration , access is allowed. For example, if the Client Address and Client IP Mask parameters are 192.168.1.0/255.255.255.0, then any client whose - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 96
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Trap Configuration This page displays an entry for every active Trap Receiver. To access this page, click System SNMP SNMP V1/V2 Trap Configuration. 1. To add a host that will receive SNMP traps, enter trap - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 97
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Trap Flags Use the Trap Flags page to enable or disable traps. When the condition identified by an active trap is encountered by the switch, a trap message is sent to any enabled SNMP Trap Receivers, and a message is - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 98
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual To configure the trap flags: 1. Use Authentication to enable or disable activation of authentication failure traps by selecting the corresponding radio button. The factory default is enabled. 2. Use Link Up/Down to enable - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 99
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Supported MIBs This page displays all the MIBs supported by the switch. To access this page, click System SNMP SNMP V1/V2 Supported MIBs. Chapter 2. Configuring System Information | 99 - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 100
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual The following table describes the SNMP Supported MIBs Status fields. Table 2-33. Field Name Description Description The RFC number if applicable and the name of the MIB. The RFC title or MIB description. 100 | Chapter - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 101
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual SNMP V3 This is the configuration for SNMP v3. From the SNMP V3 link, you can access the following pages: • User Configuration on page 101 User Configuration To access this page, click System SNMP SNMP V3 User - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 102
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual To configure SNMPv3 settings for the user account: 1. Use User Name to specify the user account to be configured disabled separately per port. By default, both transmit and receive are disabled on all ports. The application - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 103
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual The Link Layer Discovery Protocol-Media Endpoint LLDP link, you can access the following pages: • LLDP Global Configuration on page 104 • LLDP Interface Configuration on page 105 • LLDP Statistics on page 106 • LLDP - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 104
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual LLDP Global Configuration Use the LLDP Global Configuration page to specify LLDP parameters that are applied to the switch. To display this page, click System LLDP LLDP Global Configuration. A screen similar to the - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 105
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual LLDP Interface Configuration To display this page, click System LLDP LLDP Interface Configuration. A screen similar to the following displays. 1. Use Port to specify the list of ports on which LLDP - 802.1AB can be - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 106
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual LLDP Statistics To display this page, click System LLDP LLDP Statistics. A screen similar to the following displays. The following table describes the LLDP Statistics fields. Table 2-34. Field Last Update Service - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 107
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 2-34. Field Total Age outs Interface -outs that occurred on a given port. An age-out is the number of times the complete set of information advertised by a particular MAC Service Access Point (MSAP) has been deleted - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 108
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual LLDP Local Device Information To display this page, click System LLDP LLDP Local Device Information. A screen similar to the following displays. 1. Use Interface to specify the list of all the ports on which LLDP - - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 109
® Gigabit L3 Managed Stackable Switches Software Administration Manual The following table describes the LLDP Local Device Information fields. Table 2-35. Field Chassis ID Subtype Chassis ID Port ID Subtype Port ID System Name System Description Port Description System Capabilities Supported - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 110
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual LLDP Remote Device Information This page displays information on remote devices connected to the port. To display this page, click System LLDP LLDP Remote Device Information. A screen similar to the following - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 111
® Gigabit L3 Managed Stackable Switches Software Administration Manual The following table describes the LLDP Remote Device Information fields. Table 2-36. Field Chassis ID Subtype Chassis ID Port ID Subtype Port ID System Name System Description Port Description System Capabilities Supported - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 112
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual LLDP Remote Device Inventory To display this page, click System LLDP LLDP Remote Device Inventory. A screen similar to the following displays. The following table describes - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 113
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual LLDP-MED From the LLDP-MED link, you can access the following pages: • LLDP-MED Global Configuration on page 113 • LLDP-MED Interface Configuration on page 115 • LLDP-MED Local Device Information on page 116 • LLDP-MED - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 114
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual The following table describes the LLDP-MED Global Configuration fields. Table 2-38. Field Device Class Description Specifies local device's MED Classification. There are four different kinds of devices, three of them - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 115
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual LLDP-MED Interface Configuration To display this page, click System LLDP LLDP-MED Interface Configuration. A screen similar to the following displays. 1. Use Interface to specify the list of ports on which LLDP-MED - - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 116
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 2-39. Field Link Status Operational Status Description Specifies the link status of the ports to select the ports on which LLDP-MED frames can be transmitted. 116 | Chapter 2. Configuring System Information - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 117
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual , DSCP, tagged bit status and unknown bit status. A port may receive one or many such application types. If a hardware version. Firmware Revision Specifies Firmware version. Software Configuring System Information | 117 - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 118
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual LLDP-MED Remote Device Information To display this page, click System LLDP LLDP-MED Remote Device Information. A screen similar to the following displays. 1. Use Interface to select the ports on which LLDP-MED is - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 119
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual The following table describes the LLDP-MED Remote Device Information fields. Table 2-41. Field Description Capability Information: Specifies the supported and enabled capabilities that was received in MED TLV on this - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 120
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 2-41. Field Description Inventory Information: Specifies if inventory TLV is received in LLDP frames on this port. Hardware Revision Specifies hardware version of the remote device. Firmware Revision - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 121
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual LLDP-MED Remote Device Inventory To the list of all the ports on which LLDP-MED is enabled. Specifies the advertised management address of the remote system following pages: Chapter 2. Configuring System Information | 121 - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 122
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual • Global Configuration on page 123 122 | Chapter 2. Configuring System Information - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 123
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Global Configuration To display this page, click System ISDP Basic Global Configuration. A screen similar to the following displays. 1. Use Admin Mode to specify whether the ISDP Service is to be Enabled or Disabled - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 124
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Advanced From the Advanced link, you can access the following pages: • Global Configuration on page 124 • Interface Configuration on page 126 • ISDP Neighbor on page 127 • ISDP Statistics on page 128 Global Configuration - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 125
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual The following table describes the ISDP Advanced Global Configuration fields. Table 2-44. Field Neighbors table last time changed Device ID Device ID format capability Device ID format Description Displays when the - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 126
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Interface Configuration To display this page, click System ISDP Advanced Interface Configuration. A screen similar to the following displays. 1. Use Port to select the port on which the admin mode is configured. 2. - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 127
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual ISDP Neighbor To display this page, click System . These are supported: • Router • Trans Bridge • Source Route • Switch • Host • IGMP • Repeater Display the model type of the neighbor. (0 to 32) Display the port ID on the - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 128
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual ISDP Statistics To display this page, click System ISDP Advanced Statistics. A screen similar to the following displays. 128 | Chapter 2. Configuring System Information - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 129
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual The following table describes the ISDP Statistics fields. Table 2-46. Field ISDP table size of the ISDP table. Displays the table size of the ISDP IP address table. Chapter 2. Configuring System Information | 129 - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 130
the VLAN portion of the tag, in which case the first switch port to receive the packet may either reject it or insert a tag using its default VLAN ID. A given port may handle traffic for more than one VLAN, but it can only support one default VLAN ID. From the VLAN link, you can access the - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 131
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Basic From the Basic link, you can access the following pages: • VLAN Configuration on page 132 Chapter 3. Configuring Switching Information | 131 - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 132
® Gigabit L3 Managed Stackable Switches Software Administration Manual VLAN Configuration Use the VLAN Configuration page to define VLAN groups stored in the VLAN membership table. Each switch in the ProSafe® Managed Switches family supports up to 1024 VLANs. Only one VLAN is created by default - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 133
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Internal VLAN Configuration This section displays the allocation base and the allocation mode of internal VLAN. The internal VLAN is reserved by port-based routing interface and invisible to the end user. Once these - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 134
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Advanced From the Advanced link, you can access the following pages: • VLAN Configuration on page 132 • VLAN Membership on page 136 • VLAN Status on page 138 • Port PVID Configuration on page 139 • MAC Based VLAN on page - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 135
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual VLAN Configuration To display the VLAN Configuration page, click Switching VLAN Advanced VLAN Configuration. Reset Configuration - If you select this button and confirm your selection on the next screen, all VLAN - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 136
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual VLAN Membership To display the VLAN Membership page, click Switching VLAN Advanced VLAN Membership. To configure VLAN membership: 1. Use VLAN ID to select the VLAN ID for which you want to display or configure data. - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 137
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 3-48. Field VLAN Name VLAN Type Definition This field identifies the name for the VLAN you selected. It can be up to 32 alphanumeric characters long, including blanks. VLAN ID 1 always has a name of 'Default'. This - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 138
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual VLAN Status Use this page to display the status of all currently configured VLANs. To display the VLAN Status page, click Switching VLAN Advanced VLAN Status. Table 3-49. Field VLAN ID VLAN Name VLAN Type Routing - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 139
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Port PVID Configuration The Port PVID Configuration screen lets you assign a port VLAN ID (PVID) to an interface. There are certain requirements for a PVID: • All ports must have a defined PVID. • If no other value is - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 140
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual To configure PVID information: 1. Click ALL to display information for all Physical ports and LAGs. 2. Select the check box next to the interfaces to configure. You can select multiple interfaces to apply the same setting - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 141
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual MAC Based VLAN The MAC Based VLAN feature allows incoming untagged packets to be assigned to a VLAN and thus classify traffic based on the source MAC address of the packet. A MAC to VLAN mapping is defined by configuring - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 142
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IP Subnet Based VLAN IP Subnet to VLAN mapping is defined by configuring an entry in the IP Subnet to VLAN table. An entry is specified via a source IP address, network mask, and the desired VLAN ID. The IP Subnet to VLAN - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 143
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Port DVLAN Configuration To display the Port DVLAN Configuration page, click Switching VLAN Advanced Port DVLAN Configuration. 1. Use Interface to select the physical interface for which you want to display or - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 144
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Protocol Based VLAN Group Configuration You can use a protocol based VLAN to define filtering criteria for untagged packets. By default, if you do not configure any port- (IEEE 802.1Q) or protocol based VLANs, untagged - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 145
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 1. Use Group Name to assign a name to a new group. You may enter up to 16 characters. 2. Use Protocol(s) to select the protocols you want to be associated with the group. There are three configurable protocols: IP ports - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 146
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Protocol Based VLAN Group Membership To display the Protocol Based VLAN Group Membership page, click Switching VLAN Advanced Protocol Based VLAN Group Membership. 1. Use Group ID to select the protocol-based VLAN - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 147
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Voice VLAN Configuration Use this menu to configure the parameters for Voice VLAN Configuration. Note that only a user with Read/Write access privileges may change the data on this screen. To display the Voice VLAN - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 148
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 1. Use Admin Mode to select the administrative mode for Voice VLAN for the switch. The default is disable. 2. Use Interface to select the physical interface for which you want to configure data. 3. Use Interface Mode to - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 149
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual GARP Switch Configuration Note: It can take up to 10 seconds for GARP configuration changes to take effect. To display the GARP Switch Configuration page, click Switching VLAN Advanced GARP Switch Configuration. 1. - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 150
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual GARP Port Configuration Note: It can take up to 10 seconds for GARP configuration changes to take effect. To display the GARP Port Configuration page, click Switching VLAN Advanced GARP Port Configuration. 150 | - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 151
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 1. Use Interface to select the physical interface for which data is to be displayed or configured. 2. Use Port GVRP Mode to choose the GARP VLAN Registration Protocol administrative mode for the port by selecting enable or - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 152
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual It behaves appropriately to STP and RSTP bridges. A MSTP bridge can be configured to behave entirely as a RSTP bridge or a STP bridge. Note: For two bridges to be in the same region, the force version should be 802. - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 153
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual STP Configuration The Spanning Tree Configuration/Status page contains fields for enabling STP on the switch. To display the Spanning Tree Configuration/Status page, click Switching > STP > Basic STP Configuration. - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 154
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 1. Use Spanning Tree Admin Mode to specify whether spanning tree operation is enabled on the switch. Value is enabled or disabled. 2. Use Force Protocol Version to specify the Force Protocol Version parameter for the - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 155
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Advanced From the Advanced link, you can access the following pages: • STP Configuration on page 155 • CST Configuration on page 157 • CST Port Configuration on page 159 • CST Port Status on page 161 • MST Configuration on - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 156
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 1. Use Spanning Tree Admin Mode to specify whether spanning tree operation is enabled on the switch. Value is enabled or disabled. 2. Use Force Protocol Version to specify the Force Protocol Version parameter for the - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 157
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual CST Configuration Use the Spanning Tree CST Configuration page to configure Common Spanning Tree (CST) and Internal Spanning Tree on the switch. To display the Spanning Tree CST Configuration page, click Switching default - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 158
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual bridge waits between configuration messages. The value is fixed at 2 seconds. The value must be less than or equal to (Bridge Max Age / 2) - 1. The default hello time value is 2. • Bridge Forward Delay (secs) - Specifies - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 159
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual CST Port Configuration Use the Spanning Tree CST Port Configuration page to configure Common Spanning Tree (CST) and Internal Spanning Tree on a specific port on the switch. To display the Spanning Tree CST Port - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 160
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 3. Use Admin Edge Port to specify if the specified port is an Edge Port within the CIST. It takes a value of TRUE or FALSE, where the default value is FALSE. 4. Use Port Path Cost to set the Path Cost to a new value for - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 161
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual CST Port Status Use the Spanning Tree CST Port Status page to display Common Spanning Tree (CST) and Internal Spanning Tree on a specific port on the switch. To display the Spanning Tree CST Port Status page, click - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 162
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual The following table describes the CST Status information displayed on the screen. Table 3-57. Field Interface Port ID Port Forwarding State Port Role Designated Root Designated Cost Designated Bridge Designated Port - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 163
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual MST Configuration Use the Spanning Tree MST Configuration page to configure Multiple Spanning Tree (MST) on the switch. To display the Spanning Tree MST Configuration page, click Switching > STP > Advanced MST - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 164
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual For each configured instance, the information described in the following table displays on the page. Table 3-58. Field Bridge Identifier Time Since Topology Change Topology Change Count Topology - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 165
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual MST Port Status Use the Spanning Tree MST Port Status page to configure and display Multiple Spanning Tree (MST) settings on a specific port on the switch. To display the Spanning Tree MST Port Status page, click Switching - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 166
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual The following table describes the read-only MST port configuration information displayed on the Spanning Tree CST Configuration page. Table 3-59. Field Auto Calculated Port Path Cost Port ID Port Uptime Since Last Clear - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 167
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual STP Statistics Use the Spanning Tree Statistics page to view information about the number and type of bridge protocol data units (BPDUs) transmitted and received on each port. To display the Spanning Tree Statistics page, - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 168
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual The following table port. Number of RSTP BPDUs transmitted from the selected port. Number of MSTP BPDUs received at the selected port. Number of MSTP BPDUs transmitted from the selected port. Multicast Multicast IP - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 169
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual MFDB Table The Multicast Forwarding Database holds the port membership information for all active multicast address entries. will be displayed. An exact match is required. Chapter 3. Configuring Switching Information | 169 - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 170
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 3-61. Field MAC Address VLAN address is related. This displays the type of the entry. Static entries are those that are configured by the end user. Dynamic entries are added to the table as a result of a learning - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 171
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual MFDB Statistics To display the MFDB Statistics page, click Switching > Multicast > MFDB MFDB Statistics. Table 3-62. Field Max MFDB Table Entries Most MFDB Entries Since Last Reset table since last reset. This value is - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 172
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IGMP Snooping Internet Group Management Protocol (IGMP) Snooping is a feature that allows a switch to forward multicast traffic intelligently on the switch. Multicast IP traffic is traffic that is destined to a host group. - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 173
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IGMP Snooping Configuration Use the IGMP Snooping Configuration page to configure to select the unknown multicast filtering mode for the switch. The default is disable. The following table displays information about the - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 174
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IGMP Snooping Interface Configuration Use the IGMP Snooping Interface Configuration page to configure IGMP snooping settings on specific interfaces. To access the IGMP Snooping Interface Configuration page, click Switching - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 175
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual To configure IGMP Snooping interface settings: 1. Interface: Lists all physical, VLAN, and LAG interfaces. Select the interface you want to configure. 2. Use Admin Mode to select the interface mode for the selected - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 176
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IGMP VLAN Configuration Use the IGMP Snooping VLAN Configuration page to configure IGMP snooping settings for VLANs on the system. To access the IGMP Snooping VLAN Configuration page, click Switching Multicast IGMP - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 177
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual To configure IGMP snooping settings for VLANs: 1. To enable IGMP snooping on a VLAN, enter the VLAN ID in the appropriate field and configure the IGMP Snooping values: • Use Admin Mode to enable or disable IGMP Snooping - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 178
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Multicast Router Configuration This page configures the interface as the one the multicast router is attached to. All IGMP packets snooped by the switch will be forwarded to the multicast router reachable from this - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 179
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Multicast Router VLAN Configuration This page configures the interface to only forward the snooped IGMP packets that come from VLAN ID () to the multicast router attached to this interface. The configuration is not - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 180
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IGMP Snooping Querier IGMP snooping requires that one central switch or router periodically query all end-devices on the network to announce their multicast memberships. This central device is the IGMP querier. The IGMP - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 181
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual To configure IGMP Snooping Querier settings: 1. Use Querier Admin Mode to select the administrative mode for IGMP Snooping for the switch. The default is disable. 2. Use Querier IP Address to specify the Snooping Querier - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 182
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IGMP Snooping Querier VLAN Configuration Use this page to configure IGMP queriers for use with VLANs on the network. To access this page, click Switching Multicast IGMP Snooping Querier VLAN Configuration. To - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 183
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 3-65. Field Operational querier address is not configured or the network management address is also not configured. Displays the operational IGMP protocol version of the querier. Displays the IP address of the last - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 184
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual MLD Snooping From the MLD Snooping link, you can access the following pages: • MLD Snooping Configuration on page 185 • MLD Snooping Interface Configuration on page 186 • MLD VLAN Configuration on page 187 • Multicast - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 185
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual MLD Snooping Configuration Use this menu to configure the parameters for MLD Snooping, which is used to build forwarding lists for multicast traffic. Note that only a user with Read/Write access privileges may - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 186
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual MLD Snooping Interface Configuration To access the MLD Snooping Interface Configuration page, click Switching Multicast MLD Snooping Interface Configuration. 1. Interface - Displays all physical, VLAN, and LAG - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 187
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual MLD VLAN Configuration To access the MLD VLAN Configuration page, click Switching Multicast MLD Snooping MLD VLAN Configuration. 1. Use VLAN ID to set the VLAN IDs for which MLD Snooping is enabled. 2. Use Admin Mode - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 188
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Multicast Router Configuration To access the Multicast Router Configuration page, click Switching Multicast MLD Snooping Multicast Router Configuration. 1. Interface: Select the interface for which you want Multicast - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 189
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Multicast Router VLAN Configuration To access the Multicast Router VLAN Configuration page, click Switching Multicast MLD Snooping Multicast Router VLAN Configuration. 1. Use Interface to select the interface for - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 190
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual MLD Snooping Querier Configuration Use this menu to configure the parameters for Expiry Interval must be a value in the range of 60 and 300. The default value is 60. Table 3-67. Field VLAN Ids Enabled For MLD Snooping - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 191
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual MLD Snooping Querier VLAN Configuration To access the MLD Snooping Querier VLAN Configuration page, click Switching Multicast MLD Snooping Querier VLAN Configuration where in the least ip address will win the querier - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 192
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 3-68. Field Operational querier address is not configured or the network management address is also not configured. Displays the operational MLD protocol version of the querier. Displays the IP address of the last - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 193
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Address Table This table contains information about unicast entries for which the switch has forwarding and/or filtering information. This information is used by the transparent bridging function in determining how to - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 194
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 1. Use Search By to search for MAC Addresses by MAC Address, VLAN ID, and port 100. Port Status Description Displaying the number of total MAC addresses learned or configured. A unicast MAC address for which the switch - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 195
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Advanced From the Advanced link, you can access a default of 300 seconds. The value may be specified as any number between 10 and 1000000 seconds. The factory default is 300. Chapter 3. Configuring Switching Information - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 196
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Address Table This table contains information about unicast entries for which the switch has forwarding and/or filtering information. This information is used by the transparent bridging function in determining how to - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 197
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 1. Use Search By to search for MAC Addresses by MAC Address, VLAN ID, and port - Select VLAN ID from pull-down menu, enter the VLAN ID, for example 100. Then click on the "Go" button. If the address exists, the entry will - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 198
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Port Configuration Use the Port Configuration page to configure the physical interfaces on the switch. To access the Port Configuration page, click Switching Ports Port Configuration. To configure port settings: 1. Use - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 199
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 8. Click CANCEL to update the switch with the values you entered. If you want the switch to retain the new values across a power cycle you must perform a save. 9. Click APPLY to update the switch with the values you - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 200
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Port Description This screen configures and displays the description for all ports in the box. To access the Port Description page, click Switching Ports Port Description. 1. Use Port Description to enter the - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 201
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Link Aggregation Groups Link aggregation groups (LAGs), which are also known as port-channels, allow you to combine multiple full-duplex Ethernet links into a single logical link. Network devices treat the aggregation as - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 202
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual • Dest MAC,VLAN,EType,incoming port -Destination MAC, VLAN, EtherType, and incoming port associated with the packet. • Src/Dest MAC,VLAN,EType,incoming port - Source/Destination MAC, VLAN, EtherType, and incoming port - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 203
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual LAG Membership Use the LAG Membership page to select two or more full-duplex Ethernet links to be aggregated together to form a link aggregation group (LAG), which is also known as a port-channel. The switch can treat the - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 204
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual • Src MAC,VLAN,EType,incoming port - Source MAC, VLAN, EtherType, and incoming port associated with the packet. • Dest MAC,VLAN,EType,incoming port - Destination MAC, VLAN, EtherType, and incoming port associated with the - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 205
4. Routing 4 The Routing tab contains links to the following features: • Routing Table on page 205 • IP on page 213 • IPv6 on page 229 • VLAN on page 250 • ARP on page 252 • RIP on page 258 • OSPF on page 266 • OSPFv3 on - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 206
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual • Route Configuration on page 206 Route Configuration To display the Route Configuration page, click Routing Routing Table Basic Route Configuration. 206 | Chapter 4. Routing - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 207
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Route Configuration 1. Use the Route Type field to specify default or static. If creating a default route, all that needs to be specified is the next hop IP address, otherwise each field needs to be specified. 2. Network - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 208
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Learned Routes Table 4. Field Route Type Network Address Subnet Mask Protocol Next Hop IP Address Next Hop Interface Metric Preference 208 | Chapter 4. Routing Description This field can be either default or static. If - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 209
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Click REFRESH to refresh the web page to show the latest learned routes. Advanced From the Advanced link, you can access the following pages: • Route Configuration on page 209 • Route Preferences on page 212 Route - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 210
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Route Configuration 1. Use the Route Type field to specify default or static. If creating a default route, all that needs to be specified is the next hop IP address, otherwise each field needs to be specified. 2. Network - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 211
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Learned Routes Table 5. Field Description Route Type This field can be either default or static. If creating a default route, all that needs to be specified is the next hop IP address, otherwise each field needs to - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 212
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Route Preferences Use this panel to configure the default preference chosen. To avoid problems with mismatched metrics (i.e., RIP and OSPF metrics are not directly comparable) you must configure different preference values - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 213
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 6. Field Local Description This field displays the local route preference value. IP The IP folder contains links to the following web pages that configure and display IP routing data: • Basic on page 213 • - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 214
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 1. Use Routing Mode to select enable or disable. You must enable routing for the switch before you can route through any of the interfaces. The default value is disable. 2. Use ICMP Echo Replies to select enable or - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 215
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Statistics The statistics reported on this screen are as specified in RFC 1213. To display the Statistics page, click Routing IP Basic Statistics. Chapter 4. Routing | 215 - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 216
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 8. Field IpInReceives IpInHdrErrors of an unknown or unsupported protocol. The number of input IP datagrams for which no problems were encountered to prevent their continued processing, but which were discarded - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 217
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 8. Field IpOutDiscards IpOutNoRoutes IpReasmTimeout IpReasmReqds IpReasmOKs IpReasmFails IpFragOKs IpFragFails IpFragCreates IpRoutingDiscards IcmpInMsgs Description The number of output IP datagrams for which no - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 218
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual ICMP messages which this entity did not send due to problems discovered within ICMP such as a lack of buffers. outside the ICMP layer such as the inability of IP to route the resultant datagram. In some implementations there - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 219
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 8. Field IcmpOutParmProbs IcmpOutSrcQuenchs IcmpOutRedirects IcmpOutEchos IcmpOutEchoReps IcmpOutTimestamps IcmpOutTimestampReps IcmpOutAddrMasks IcmpOutAddrMaskReps Description The number of ICMP Parameter Problem - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 220
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Advanced From the Advanced link, you can access the following pages: • IP Configuration on page 220 • IP Statistics on page 222 • IP Interface Configuration on page 227 • Secondary IP Address on page 229 IP Configuration - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 221
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 1. Use Routing Mode to select enable or disable. You must enable routing for the switch before you can route through any of the interfaces. The default value is disable. 2. Use ICMP Echo Replies to select enable or - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 222
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IP Statistics The statistics reported on this screen are as specified in RFC 1213. To display the IP Statistics page, click Routing IP Advanced IP Statistics. 222 | Chapter 4. Routing - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 223
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 10. Field IpInReceives IpInHdrErrors of an unknown or unsupported protocol. The number of input IP datagrams for which no problems were encountered to prevent their continued processing, but which were discarded - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 224
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 10. Field IpOutDiscards of its default gateways are down. The maximum number of seconds which received fragments are held while they are awaiting reassembly at this entity. The number of IP fragments received - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 225
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual ICMP messages which this entity did not send due to problems discovered within ICMP such as a lack of buffers. outside the ICMP layer such as the inability of IP to route the resultant datagram. In some implementations there - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 226
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 10. Field IcmpOutParmProbs IcmpOutSrcQuenchs IcmpOutRedirects IcmpOutEchos IcmpOutEchoReps IcmpOutTimestamps IcmpOutTimestampReps IcmpOutAddrMasks IcmpOutAddrMaskReps Description The number of ICMP Parameter - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 227
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IP Interface Configuration Use the IP Interface Configuration page to update IP interface data for this switch. To display the IP Interface Configuration page, click Routing IP Advanced IP Interface Configuration. 1. - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 228
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual broadcasts will be forwarded. If you select disable they will be dropped. The default . Use Bandwidth to specify the configured bandwidth on this interface. This parameter uses bandwidth to compute link cost. Valid range is (1 - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 229
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Secondary IP Address To display the Secondary IP Address page, click Routing IP Advanced Secondary IP. 1. Use Interface to select the interface for which data is to be displayed or configured. 2. Use Secondary IP - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 230
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual access to both. Routing protocols are capable of computing routes for one or both IP versions. From the IPv6 link, you can access the following pages: • Basic on page 230 • Advanced on page 233 Basic From the Basic link, - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 231
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IPv6 Global Configuration Use the Global Configuration page to enable IPv6 forwarding on the router and to enable the forwarding of IPv6 unicast datagrams. To display the IPv6 Global Configuration page, click Routing - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 232
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IPv6 Route Table Use the a "Null0" interface. Next Hop IP Address Displays the Next Hop IPv6 Address for the Active Route. Preference Displays the Route Preference of the Configured Route. Click REFRESH to refresh the - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 233
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Advanced From the Basic link, you can access the following pages: • IPv6 Global Configuration on page 234 • IPv6 Interface Configuration on page 235 • IPv6 Prefix Configuration on page 237 • IPv6 Statistics on page 238 • - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 234
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IPv6 Global Configuration Use the Global Configuration page to enable IPv6 forwarding on the router and to enable the forwarding of IPv6 unicast datagrams. To display the IPv6 Global Configuration page, click Routing - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 235
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IPv6 Interface Configuration Use the Interface Configuration page to configure IPv6 interface parameters. To display the IPv6 Interface Configuration page, click Routing IPv6 Advanced Interface Configuration default - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 236
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 10. Use Adv Interval to specify the maximum time allowed between sending router advertisements from the interface. Default value is 600. Range of maximum advertisement interval is 4 to 1800. 11. Use Adv Managed Config - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 237
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IPv6 Prefix Configuration To display the IPv6 Prefix Configuration page, click Routing IPv6 Advanced Prefix Configuration. 1. Use Interface to select the interface to be configured. When the selection is changed, a - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 238
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IPv6 Statistics Use the IPv6 Statistics page select the interface to be configured. When the selection is changed, a screen refresh will occur causing all fields to be updated for the newly selected port. 238 | Chapter 4. - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 239
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IPv6 Statistics Table 16. Field Description Datagrams Discarded Other The number of input IPv6 datagrams for which no problems were encountered to prevent their continued processing, but which were discarded (e.g., - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 240
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 16. Field Received Datagrams Reassembly Required Datagrams Successfully Reassembled Datagrams Failed To Reassemble Datagrams Forwarded Datagrams Locally Transmitted Datagrams Transmit Failed Datagrams Successfully - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 241
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 16. Field Multicast Datagrams Received messages received by the interface. ICMPv6 Parameter Problem Messages Received The number of ICMP Parameter Problem messages received by the interface. ICMPv6 Packet - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 242
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 17. Field Description ICMPv6 Neighbor To Error The number of ICMP messages which this interface did not send due to problems discovered within ICMP such as a lack of buffers. This value should not include - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 243
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 17. Field ICMPv6 Neighbor Solicit Messages Transmitted ICMPv6 Neighbor Advertisement Messages Transmitted ICMPv6 Redirect Messages Transmitted ICMPv6 Group Membership Query Messages Transmitted ICMPv6 Group - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 244
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IPv6 Neighbor Table Use the IPv6 Searched by Interface - Select Interface from pull-down menu, enter the interface ID in Unit/Slot/Port, for example 2/1/1. Then click Go. If the IPv6 route exists, the entry will be - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 245
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 18. Field Neighbor State Last Updated Description Specifies the state of the neighbor cache entry. Following are the states for dynamic entries in the IPv6 neighbor discovery cache: • Incmp - Address resolution - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 246
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IPv6 Route Configuration To display the IPv6 Route Configuration page, click Routing IPv6 Advanced Static Route Configuration for the Configured Route. 4. Use Interface to specify the unit, slot, and port number for - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 247
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IPv6 Route Table To display the IPv6 Route Table page, click Routing IPv6 Advanced Route Table. 1. Use Routes Displayed to display: • Configured Routes - Shows the routes configured by the user. • Best Routes - Shows - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 248
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IPv6 Route Preferences Use this panel to configure the default best route metric will be chosen. To avoid problems with mismatched metrics you must configure different preference values for each of the protocols. - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 249
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Tunnel Configuration ProSafe® Managed Switches software provides for the creation, deletion, and management of tunnel interfaces. These are dynamic interfaces that are created and deleted via user-configuration. ProSafe® - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 250
Gigabit L3 Managed Stackable Switches Software Administration Manual VLAN You can configure ProSafe® Managed Switches software with some ports supporting VLANs and some supporting routing. You can also configure the software to allow traffic on a VLAN to be treated as if the VLAN were a router port - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 251
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual VLAN Routing Wizard The VLAN Routing Wizard creates a VLAN, adds selected ports to the VLAN. The VLAN Wizard gives the user the option to add the selected ports as a Link Aggregation (LAG). The Wizard will: • Create a VLAN - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 252
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual VLAN Routing Configuration Use the VLAN Routing Configuration page to configure VLAN Routing interfaces on the system. To display the VLAN Routing Configuration page, click Routing VLAN VLAN Routing. 1. Use VLAN ID to - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 253
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual hop router, if the destination is not content in the ARP cache. The number of supported ARP entries is platform-dependent. Devices can be moved in a network, which means the IP address that was at one time associated with - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 254
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual ARP Cache Use this screen to show ARP entries in the ARP Cache. To display the ARP Cache page, click Routing ARP Basic ARP Cache. 1. Use Port to select the associated Unit/Slot/Port of the connection 2. IP Address - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 255
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Advanced .From the Advanced link, you can access the following pages: • Static ARP Cache on page 255 • ARP Table Configuration on page 257 Static ARP Cache To display the Static ARP Cache page, click Routing ARP - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 256
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual ARP Cache Use this screen to show ARP entries in the ARP Cache. Table 22. Field Description Port The associated Unit/Slot/Port of the connection IP Address Displays the IP address. It must be the IP address of a - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 257
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual ARP Table Configuration You can use this screen to change the configuration of type Dynamic when they age out. The default setting is Enable. 6. Use Remove from Table required IP Address. • Specific Static Entry - Selecting - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 258
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual • None - Selected if the user does not want to delete any entry from the ARP Table. 7. Use Remove IP Address to enter the IP ARP table. Total number of Configured Static Entries in the ARP RIP update packets that are sent - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 259
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual RIP Configuration Use the RIP Configuration page to enable and configure or disable RIP in Global mode. To display the RIP Configuration page, click Routing RIP Basic RIP Configuration. 1. Use RIP Admin Mode to - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 260
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Advanced From the Advanced link, you can access the following pages: • RIP Configuration on page 260 • Interface Configuration on page 262 • Route Redistribution on page 265 RIP Configuration Use the RIP Configuration page - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 261
® Gigabit L3 Managed Stackable Switches Software Administration Manual 1. Use RIP Admin Mode to enable or disable RIP for the switch. The default is enable. 2. Use Split Horizon Mode to select none, simple, or poison reverse from the radio buttons. Split horizon is a technique for avoiding problems - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 262
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Interface Configuration Use the RIP Interface Configuration page to enable and configure or to disable RIP on a specific interface. To display the Interface Configuration page, click Routing RIP Advanced Interface - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 263
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual RIP Interface Configuration 1. Use Interface to select the interface for which data is to be configured • RIP-2 - Accept only RIP version 2 formatted packets. The default is RIP-2. • Both - Accept packets in either format. - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 264
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual RIP Status Table 26. Field Description Interface IP Address Displays the interface for which data is configured. Displays the IP an interface. The default is Disable. Indicates Bad Routes Received Updates Sent The - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 265
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Route Redistribution Use the RIP Route Redistribution page to configure Source IP Address and netmask • Destination IP Address and netmask • Action (permit or deny) All other fields (source and destination port, precedence - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 266
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual The source IP address is compared to the destination IP address of the route. The source IP netmask in the access list rule is treated as a wildcard mask, indicating which bits in the source IP when not configured. OSPF - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 267
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Basic From the Basic link, you can access the following pages: • OSPF Configuration on page 267 OSPF Configuration Use the OSPF Configuration page to enable OSPF on a router and to configure effect. The default value is - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 268
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Advanced From the Advanced link, you can access the following pages: • OSPF Configuration on page 269 • Common Area Configuration on page 272 • Stub Area Configuration on page 274 • NSSA Area Configuration on page 276 • - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 269
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual OSPF Configuration Use the OSPF Configuration page to enable OSPF on a router and to configure the related OSPF settings. To display the OSPF Configuration page, click Routing OSPF Advanced OSPF Configuration. Default - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 270
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual OSPF Configuration 1. Use Router ID to specify the 32-bit integer in dotted decimal format that uniquely identifies the router within the autonomous system (AS). If you - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 271
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual second. Unless a link cost is configured, the link cost is computed by dividing the reference bandwidth by the interface bandwidth. The range is 1 to 4294967. 12. Use Default Passive Setting to configure the global - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 272
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Common Area Configuration The OSPF Common Area Configuration page lets you create a Common Area Configuration once you have enabled OSPF on an interface. At least one router must have OSPF enabled for this web page to - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 273
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 1. Use Area ID to enter the OSPF the area is a stub area, then these are the possible options for which you may configure the external routing capability, otherwise the only option is "Import External LSAs": • Import - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 274
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Stub Area Configuration To display the Stub Area Configuration page, click Routing OSPF Advanced Stub Area Configuration. 1. Use Area ID to enter the OSPF area ID. An Area ID is a 32-bit integer in dotted decimal - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 275
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 30. Field SPF Runs Area Border Router Count Area LSA Count Area LSA Checksum Type of Service Description The number of times that the intra-area route table has been calculated using this area's link-state database - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 276
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual NSSA Area Configuration To display the NSSA Area Configuration page, click Routing OSPF Advanced NSSA Area Configuration. 1. Use Area ID to enter the OSPF area ID. An Area ID is a 32-bit integer in dotted decimal - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 277
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 8. Click DELETE to delete the NSSA area designation. The area will be returned to normal state. Table 31. Field SPF Runs Area Border Router Count - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 278
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Area Range Configuration Use the OSPF Area Range Configuration page to configure and display an area range for a specified NSSA. To display the Area Range Configuration page, click Routing OSPF Advanced Area Range - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 279
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Interface Configuration Use the OSPF Interface Configuration page to configure an OSPF interface. To display the Interface Configuration page, click Routing OSPF Advanced Interface Configuration. 1. Interface - The - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 280
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Admin Mode is enabled: State, Designated Router, Backup Designated Router, Number of Link Events, LSA ACK Interval, and Metric Cost. For OSPF to be fully functional, you must enter a valid IP Address and Subnet Mask via - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 281
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 12. Use Authentication Type to select an authentication type other than none. You can select the authentication type from the pull-down menu. The choices - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 282
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 32. Field State Designated Router Backup pings to the interface or through something like a bit error test. For this reason, IP packets may still be addressed to an interface in Loopback state. To facilitate this, - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 283
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 32. Field Designated Router Backup Designated Router Number of Link Events Local Link LSAs Local Link LSA Checksum Description The identity of the Designated - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 284
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual OSPF Interface Statistics This screen displays statistics for the selected interface. The information will be displayed only if OSPF is enabled. To display the OSPF - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 285
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 33. Field OSPF Area ID Area Border Router Count AS Border Router Count Area LSA Count IP of received packets discarded because the source IP address is not within a subnet configured on a local interface. The number - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 286
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 33. Field Area Mismatch Invalid OSPF header is not the area ID configured on the ingress interface. The number of OSPF packets discarded because the packet's destination IP address is not the address of the - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 287
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 33. Field Description LS Updates Received The number of LS updates received on this interface by this router. LS Acknowledgements Sent The number of LS acknowledgements sent on this interface by this router. - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 288
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual OSPF Neighbor Table This screen displays the OSPF to be displayed or configured. Slot 0 is the base unit. A 32-bit integer in dotted decimal format representing the neighbor interface. The IP address of the neighboring - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 289
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 34. Field Description Neighbor Interface Index A Unit/Slot/Port identifying the neighbor interface index. State The state of a neighbor can be the following: • Down - This is the initial state of a neighbor - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 290
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Click REFRESH to show the latest DHCP bindings information. Click CLEAR to clear all the neighbors in the table. 290 | Chapter 4. Routing - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 291
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual system (AS). The Router ID is set on the IP Configuration page. If you want to change the Router ID you must re-enable OSPF to have the change take effect. The default value is 0.0.0.0, although this is not a valid Router ID - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 292
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 35. Field IP multicast datagrams are forwarded according to the standard specifications. • O: This describes whether Opaque-LSAs are supported. • V: This describes whether OSPF++ extensions for VPN/COS are supported - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 293
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Virtual Link Configuration Use the OSPF Virtual Link Configuration page to create or configure virtual interface information for a specific area and neighbor. A valid OSPF area must be configured before this page can be - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 294
® Gigabit L3 Managed Stackable Switches Software Administration Manual • Simple - If you select 'Simple' you will be prompted to enter an authentication key. This key will be included, in the clear, in the OSPF header of all packets sent on the network. All routers on the network must be configured - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 295
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Route Redistribution This screen can be used to configure are: • Source IP Address and netmask • Destination IP Address and netmask • Action (permit or deny) All other fields (source and destination port, precedence, tos, - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 296
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual The source IP address is compared to the destination IP address of the route. The source IP netmask in the access list rule is treated as a wildcard mask, indicating which bits in the source IP are also supported in order - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 297
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual OSPFv3 Configuration Use the OSPFv3 Configuration page to activate and configure OSPFv3 for a switch. To display the OSPFv3 Configuration page, click Routing OSPFv3 Basic OSPFv3 Configuration . The default value is - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 298
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Advanced From the Advanced link, you can access the following pages: • OSPFv3 Configuration on page 299 • Common Area Configuration on page 302 • Stub Area Configuration on page 304 • NSSA Area Configuration on page 306 • - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 299
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual OSPFv3 Configuration Use the OSPFv3 Configuration page to activate and configure OSPFv3 for a switch. To display the OSPFv3 Configuration page, click Routing OSPFv3 Advanced OSPFv3 Configuration. Default Route - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 300
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual OSPFv3 Configuration 1. Use Router configure the auto-cost reference-bandwidth to control how OSPF calculates default metrics for the interface. The valid values are 1 to 4294967. 8. Use Default Passive Setting to configure - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 301
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 37. Field ASBR Mode ABR router is an autonomous system border router. Router automatically becomes an ASBR when it is configured to redistribute routes learnt from other protocol. The values of this are enabled or - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 302
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Common Area Configuration Use the Common Area Configuration page to create and configure an OSPFv3 area. To display the Common Area Configuration page, click Routing OSPFv3 Advanced Common Area Configuration. 1. Use - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 303
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 38. Field External Routing SPF Runs Area Border Router Count Area LSA Count Area LSA Checksum Import Summary LSAs Description A definition of the router's - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 304
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Stub Area Configuration To display the Stub Area Configuration page, click Routing OSPFv3 Advanced Stub Area Configuration. 1. Use Area ID to enter the OSPF area ID. An Area ID is a 32 bit integer in dotted decimal - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 305
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 39. Field SPF Runs Area Border Router Count Area LSA Count Area LSA Checksum Type of Service Description The number of times that the intra-area route table has been calculated using this area's link-state database - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 306
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual NSSA Area Configuration To display the NSSA Area Configuration page, click Routing OSPFv3 Advanced NSSA Area Configuration. 1. Use Area ID to enter the OSPF area ID. An Area ID is a 32-bit integer in dotted decimal - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 307
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 40. Field SPF Runs Area Border Router Count Area LSA Count Area LSA Checksum Translator State Description The number of times that the intra- - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 308
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Area Range Configuration Use the Area Range Configuration page to configure OSPFv3 area ranges. To display the Area Range Configuration page, click Routing OSPFv3 Advanced Area Range Configuration. 1. Use Area ID to - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 309
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Interface Configuration Use the OSPFv3 Interface Configuration page to create and configure OSPFv3 interfaces. To display the Interface Configuration page, click Routing OSPFv3 Advanced Interface Configuration. 1. - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 310
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Link Events, LSA ACK Interval, and Metric Cost. For OSPFv3 to be fully functional, the interface must have a valid IPv6 Prefix/Prefix Length. This can be done through the CLI using the IPv6 - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 311
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 41. Field IPv6 Address LSA Ack ICMP pings to the interface or through something like a bit error test. For this reason, IP packets may still be addressed to an interface in Loopback state. To facilitate this, such - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 312
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 41. Field Backup Designated Router Number of Link Events Description The identity of the Backup Designated Router for this network, in the view of - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 313
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Interface Statistics This screen displays statistics for the selected interface. The information will be displayed only if OSPFv3 is enabled. To display the Interface Statistics - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 314
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 42. Field OSPFv3 Area ID Area Border Router Count AS Border Router Count Area LSA Count IPv6 Address Interface Events Virtual Events Neighbor Events - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 315
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 42. Field Area Mismatch Invalid Destination Address No Neighbor at Source Address Invalid OSPF Packet Type Hellos Ignored Hellos Sent Hellos Received DD Packets - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 316
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Neighbor Table This screen shows the OSPFv3 Neighbor Table. This information is displayed only if OSPFv3 is enabled and there exists at least on OSPFv3 - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 317
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 43. Field Description Interface The Interface for which the data needs to be displayed. Router ID A 32-bit integer in dotted decimal format representing - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 318
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual (AS). The Router ID is set on the OSPFv3 Configuration page. If you want to change the Router ID you must re-enable OSPFv3 to have the change take effect. The default value is 0.0.0.0, although this is not a valid Router ID - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 319
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 44. Field LSA Type LS ID Age Sequence Checksum Description The format and function of the link state advertisement. One of the following: • Router - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 320
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 44. Field Description Options The Options field in the link state advertisement header indicates which optional capabilities are associated with the advertisement. The options are: • Q: This enables support for - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 321
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Virtual Link Configuration Use the Virtual Link Configuration page to define a new or configure an existing virtual link. To display this page, a valid OSPFv3 area must be defined via the OSPFv3 Area Configuration page. To - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 322
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 45. Field Neighbor State State Metric Description The state of the Virtual Neighbor Relationship. The state of the interface: • Down: This is the initial - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 323
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Route Redistribution This screen can be used to configure if the source was pre-configured, else a default tag value of 0 is IP Addresses it is associated with. Hosts listen for these advertisements and discover the IP - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 324
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual • Router Discovery Configuration on page 324 Router Discovery Configuration Use the Router Discovery Configuration page to enter or change Router Discovery parameters. To display the Router Discovery Configuration page, - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 325
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 1. Use Interface to select the router interface for which data is to be configured. 2. Use Advertise Mode to select enable or disable. If you select enable, Router Advertisements will be transmitted from the selected - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 326
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 326 | Chapter 4. Routing - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 327
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 1. VRID is only configurable if you are creating new Virtual Router, in which case enter the VRID in the range 1 to 255. 2. Use Interface to select the Unit/Slot/Port for the new Virtual Router from the pull-down menu. 3. - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 328
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 46. Field Interface IP Address Owner VMAC Address State Description Indicates the IP Address associated with the selected interface. Set to 'True' if the Virtual IP Address and the Interface IP Address are the same - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 329
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Advanced From the Advanced link, you can access the following pages: • VRRP Configuration on page 329 • VRRP Secondary IP on page 331 • Tracking Configuration on page 332 • Virtual Router Statistics on page 333 VRRP - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 330
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 7. Use Primary IP Address to enter the IP Address associated with the Virtual Router. The default is 0.0.0.0. 8. Use Authentication Type to select the type of Authentication for the Virtual Router from the pull-down menu. - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 331
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual VRRP Secondary IP To display the VRRP Secondary IP page, click Routing VRRP Advanced VRRP Secondary IP. 1. Use VRRP ID and Interface to select one of the existing Virtual Routers, listed by interface number and VRRP - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 332
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Tracking Configuration Use Tracking Configuration to track specific route IP states within the router that can alter the priority level of a virtual router for a VRRP group. To display the Tracking Configuration Default - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 333
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Errors Authentication Failure IP TTL Errors Description the selected Virtual Router. The Unit/Slot/Port for the selected Virtual Router. The time, interval was different than the one configured for the local virtual router. - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 334
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 50. Field Description access the following pages: • Mroute Table on page 335 • Multicast Global Configuration on page 336 • Multicast Interface Configuration on page 337 • DVMRP on page 338 • IGMP on page 346 - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 335
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Mroute Table This screen displays contents of the Mroute Table in tabular form. To display the Mroute Table page, click Routing Multicast Mroute Table. Table 51. Field Source IP Group IP Incoming Interface Outgoing - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 336
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 51. Field Protocol Flags Description The Configuration page, click Routing Multicast Global Configuration. 1. Use Admin Mode to set the administrative status of Multicast Forwarding in the router. The default - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 337
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Multicast Interface Configuration To display the Multicast Interface Configuration page, click Routing Multicast Interface Configuration. 1. Interface - The routing interface you want to configure or displayed. 2. Use - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 338
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual DVMRP From the DVMRP link, you can access the following pages: • DVMRP Global Configuration on page 338 • DVMRP Interface Configuration on page 339 • DVMRP Neighbor on page 341 • DVMRP Next Hop on page 343 • DVMRP Prune on - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 339
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual DVMRP Interface Configuration To display the DVMRP Interface Configuration page, click Routing Multicast DVMRP Interface Configuration. 1. Use Interface to select the interface for which data is to be configured. 2. - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 340
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 54. Field Protocol State Local The IP address used as a source address in packets sent from the selected interface. The DVMRP generation ID used by the router for the selected interface. This value is reset every - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 341
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual DVMRP Neighbor To display the DVMRP Neighbor page, click Routing Multicast DVMRP DVMRP Neighbor. 1. Interface - Select the interface for which data is to be displayed, - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 342
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 55. Field State Up Time Expiry Time Generation ID Major Version Minor Version Capabilities Received Routes Received Bad Packets Received Bad Routes Description The - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 343
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual DVMRP Next Hop To display the DVMRP Next Hop page, click Routing Multicast DVMRP DVMRP Next Hop. Table 56. Field Source IP Source Mask Next Hop Interface Type Description The IP address used with the source mask to - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 344
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual DVMRP Prune To display the DVMRP Prune page, click Routing Multicast DVMRP DVMRP Prune. Table 57. Field Group IP Source IP of the default prune lifetime timer, otherwise it is set to the smallest received value or - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 345
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual DVMRP Route To display the DVMRP Route of the upstream neighbor (e.g., RPF neighbor) from which IP datagrams from these sources are received. The interface on which IP datagrams sent by these sources are received. A value - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 346
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IGMP From the IGMP link, you can access the following pages: • IGMP Global Configuration on page 346 • IGMP Routing Interface Configuration on page 347 • IGMP Routing Interface Statistics on page 349 • IGMP Groups on page - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 347
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IGMP Routing Interface Configuration To display the IGMP Routing Interface Configuration page, click Routing Multicast IGMP Routing Interface Configuration. Chapter 4. Routing | 347 - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 348
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 1. Interface - The interface for which data is to be displayed or configured. 2. Use Admin Mode to set the administrative status of IGMP on the selected interface. The default second. The default value is 100. Valid values - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 349
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IGMP Routing Interface Statistics To display the IGMP Routing Interface Statistics page, click Routing Multicast IGMP Routing Interface Statistics. Chapter 4. Routing | 349 - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 350
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 59. Field Description Interface IP Address Subnet Mask Protocol State Querier IP Querier Status Querier Up Time The interface on which the IGMP is enabled. The IP address of the selected interface. The subnet - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 351
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IGMP Groups To display the IGMP Groups page, click Routing Multicast IGMP IGMP Groups. Chapter 4. Routing | 351 - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 352
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 60. Field Description Interface Multicast Group IP The interface which data is to be displayed. The IP multicast group address for which data is to be displayed. Last Reporter Up Time The IP address of the - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 353
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IGMP Membership To display the IGMP Membership page, click Routing Multicast IGMP IGMP Membership. Table 61. Field Description Group IP The IP multicast group address for which data is to be displayed. Interface - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 354
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IGMP Proxy Interface Configuration To display the IGMP Proxy Interface Configuration page, click Routing Multicast IGMP Proxy Interface Configuration. 1. Use Interface to select the port for which data is to be - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 355
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 62. Field IP Address Subnet Mask Operational Mode Number of Groups Version 1 Querier Timeout Version 2 Querier Timeout Proxy Start Frequency Description The IP address of the IGMP Proxy interface. The subnet mask - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 356
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IGMP Proxy Interface Statistics To display the IGMP Proxy Interface Statistics page, click Routing Multicast IGMP Proxy Interface Statistics. Table 63. Field Description Interface Displays - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 357
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IGMP Proxy Membership To display the IGMP Proxy Membership page, click Routing Multicast IGMP Proxy Membership. Chapter 4. Routing | 357 - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 358
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 64. Field Description Group IP Displays the IP multicast group address. Proxy Interface Displays the interface on which IGMP proxy is enabled. Source Hosts This parameter shows source addresses which are - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 359
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual PIM-DM From the PIM-DM link, you can access the following pages: • PIM-DM Global Configuration on page 359 • PIM-DM Interface Configuration on page 360 • PIM-DM Neighbor on page 361 PIM-DM Global Configuration To display - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 360
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual PIM-DM Interface Configuration To display the PIM-DM Interface Configuration page, click Routing Multicast PIM-DM Interface Configuration. 1. Interface - The interface for which data is to be displayed or configured. - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 361
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual PIM-DM Neighbor To display the PIM-DM Neighbor page, click Routing Multicast PIM-DM Neighbor Configuration. Table 66. Field Description Interface Neighbor IP The physical interface on which PIM-DM is enabled. The - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 362
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual PIM-SM From the PIM-SM link, you can access the following pages: • PIM-SM Global Configuration on page 362 • PIM SSM Configuration on page 363 • PIM-SM Interface Configuration on page 364 • PIM-SM Neighbor on page 366 • - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 363
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual PIM SSM Configuration While PIM-SM employs a specially-configured connected LANs. The SSM service model can be implemented with a strict subset of the PIM-SM protocol mechanisms. Both regular IP Multicast and SSM semantics - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 364
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual PIM-SM Interface Configuration To display the PIM-SM Interface Configuration page, click Routing Multicast PIM-SM Interface Configuration. 364 | Chapter 4. Routing - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 365
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 1. Interface - The interface for which data is to be configured or to be displayed. 2. Use Admin Mode to set the administrative status of PIM-SM in the router. The default is disable. 3. Use Hello Interval(secs) to enter - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 366
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual PIM-SM Neighbor To display the PIM-SM Neighbor page, click Routing Multicast PIM-SM PIM-SM Neighbor. Table 68. Field Interface Neighbor IP Description The interface on which neighbor is displayed. The IP address of - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 367
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual PIM-SM Candidate RP Configuration To display the PIM-SM Candidate RP Configuration page, click Routing Multicast PIM-SM Candidate RP Configuration. 1. Use Interface to select the interface for which data is to be - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 368
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual PIM-SM BSR Candidate Configuration To display the PIM-SM BSR Candidate Configuration page, click Routing Multicast PIM-SM BSR Candidate Configuration values are from 0 to 32. Default value is 30. 4. Click DELETE to - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 369
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual PIM-SM Static RP Configuration This page is used to statically configure the RP address for one or more multicast groups. To display the PIM-SM Static RP Configuration page, click Routing Multicast PIM-SM Static RP - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 370
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Static Routes Configuration To display the Static Routes Configuration page, click Routing Multicast Static Routes Configuration. 1. Use Source IP to enter the IP Address that identifies the multicast packet source for - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 371
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Admin Boundary Configuration The definition of applied to the multicast group address. The combination of the mask and the Group IP gives the range of administratively scoped addresses for the selected interface. 4. Click - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 372
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Mroute Table This screen displays contents of the Mroute Table in tabular form. To display the Mroute Table page, click Routing IPv6 Multicast Mroute Table. 372 | Chapter 4. Routing - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 373
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 70. Field Source IP Group IP Incoming Interface Outgoing Interface(s) Up Time(hh:mm:ss) Expiry Time(hh:mm:ss) RPF Neighbor Protocol Flags Description The IP address of the multicast packet source to be combined - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 374
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IPv6 PIM-DM From the IPv6 PIM-DM link, you can access the following pages: • PIM-DM Global Configuration on page 374 • PIM-DM Interface Configuration on page 375 • PIM-DM Neighbor on page 376 PIM-DM Global Configuration To - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 375
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual PIM-DM Interface Configuration To display the IPv6 PIM-DM Interface Configuration page, click Routing IPv6 Multicast PIM-DM Interface Configuration. 1. Interface - The interface for which data is to be displayed or - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 376
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual PIM-DM Neighbor To display the IPv6 PIM-DM Neighbor page, click Routing IPv6 Multicast PIM-DM PIM-DM Neighbor. Table 72. Field Interface Description The physical interface on which PIM-DM is enabled. Neighbor IP - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 377
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IPv6 PIM-SM From the IPv6 PIM-SM link, you can access the following pages: • PIM-SM Global Configuration on page 377 • PIM SSM Configuration on page 378 • PIM-SM Interface Configuration on page 379 • PIM-SM Neighbor on - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 378
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual PIM SSM Configuration While PIM-SM employs a specially-configured connected LANs. The SSM service model can be implemented with a strict subset of the PIM-SM protocol mechanisms. Both regular IP Multicast and SSM semantics - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 379
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual PIM-SM Interface Configuration To display the IPv6 PIM-SM Interface Configuration page, click Routing IPv6 Multicast PIM-SM Interface Configuration. Chapter 4. Routing | 379 - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 380
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 1. Interface - The interface for which data is to be configured or to be displayed. 2. Use Admin Mode to set the administrative status of PIM-SM in the router. The default is disable. 3. Use Hello Interval(secs) to enter - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 381
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual PIM-SM Neighbor To display the IPv6 PIM-SM Neighbor page, click Routing IPv6 Multicast PIM-SM PIM-SM Neighbor. Table 74. Field Description Interface The interface on which neighbor is displayed. Neighbor IP The - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 382
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual PIM-SM Candidate RP Configuration To display the IPv6 PIM-SM Candidate RP Configuration page, click Routing IPv6 Multicast PIM-SM Candidate RP Configuration. 1. Use Interface to select the interface for which data is - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 383
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual PIM-SM BSR Candidate Configuration To display the IPv6 PIM-SM BSR Candidate Configuration page, click Routing IPv6 Multicast PIM-SM BSR Candidate Configuration. 1. Use Interface to select the interface for which data - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 384
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual PIM-SM Static RP Configuration This page is used to statically configure the RP address for one or more multicast groups. To display the IPv6 PIM-SM Static RP Configuration page, click Routing IPv6 Multicast PIM-SM - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 385
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual MLD From the MLD link, you can access the following pages: • MLD Global Configuration on page 385 • MLD Routing Interface Configuration on page 386 • MLD Routing Interface Statistics on page 388 • MLD Groups on page 389 • - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 386
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual MLD Routing Interface Configuration To display the MLD Routing Interface Configuration page, click Routing IPv6 Multicast MLD Routing Interface Configuration. 386 | Chapter 4. Routing - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 387
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 1. Use Interface to select the interface for which data is to be configured or displayed. 2. Use Admin Mode to set the administrative status of MLD on the selected interface. The default value is disable. 3. Use Version - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 388
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual MLD Routing Interface Statistics To display the MLD Routing Interface Statistics page, click Routing IPv6 Multicast MLD Routing Interface Statistics. Table 77. Field Interface Querier Status Querier IP the IP subnet - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 389
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Click REFRESH to refresh the data on the interface on which data is displayed. Indicates the address of the Mgmd members. The IP Address of the source of the last membership report received for this multicast group address - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 390
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 78. Field Description Source Hosts This parameter shows source addresses which are members of this multicast address. Source Address(Expiry Time) This parameter shows - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 391
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 79. Field Description Leaves Received The number of valid MLD leaves received by the router. Leaves Sent The number of valid MLD leaves sent - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 392
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual MLD Proxy Interface Configuration To display the MLD Proxy Interface Configuration page, click Routing IPv6 Multicast MLD Proxy Interface Configuration. 1. Use Interface to select the interface to be configured. 2. - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 393
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 80. Field IPv6 Prefix Prefix Length Operational Mode Number of Groups Version 1 Querier Timeout Proxy Start Frequency Description The IPv6 address of the MLD - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 394
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual MLD Proxy Interface Statistics To display the MLD Proxy Interface Statistics page, click Routing IPv6 Multicast MLD Proxy Interface Statistics. Table 81. Field Proxy Interface - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 395
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual MLD Proxy Membership To display the MLD Proxy Membership page, click Routing IPv6 Multicast MLD Proxy Membership. Chapter 4. Routing | 395 - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 396
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 82. Field Description Group IP Source Hosts The IPv6 multicast group address. This parameter shows source addresses which are members of this multicast address. Last Reporter Up Time The IPv6 - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 397
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Static Routes Configuration To display the Static Routes Configuration page, click Routing IPv6 Multicast Static Routes Configuration. 1. Use Source IP to enter the IP Address that identifies the multicast packet source - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 398
the features in the QoS tab to configure Quality of Service (QoS) settings on the switch. The QoS tab contains links to the following features: • Class of Service on page 398 • Differentiated Services on page 407 In a typical switch, each physical port consists of one or more queues for transmitting - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 399
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual From the Class of Service link under the QoS tab, you can access the following pages: • Basic on page 399 • Advanced on page 401 Basic From the Basic link, you can access the following pages: • CoS Configuration on page - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 400
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Use the CoS Configuration page to set the class of service trust mode of an interface. Each port in the switch can be configured to trust one of the packet fields (802.1p or IP DSCP), or to not trust any packet's priority - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 401
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Advanced From the Advanced link, you can access the following pages: • CoS Configuration on page 401 • 802.1p to Queue Mapping on page 402 (Advanced) • IP DSCP to Queue Mapping on page 403 (Advanced • CoS Interface - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 402
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual configuration settings based per-interface or specify all CoS configurable hardware queue for a port. Higher traffic class values configuration on the screen and reset the data on the screen to the latest value of the switch - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 403
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IP DSCP to Queue Mapping Use the IP DSCP to Queue Mapping page to specify which internal traffic class to map the corresponding DSCP value. To display the IP DSCP Queue Mapping page, click QoS CoS Advanced IP DSCP to - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 404
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual CoS Interface Configuration Use the CoS Interface Configuration page to apply an interface shaping rate to all interfaces or to a specific interface. To display the CoS Interface Configuration page, click QoS CoS> - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 405
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual To configure CoS settings for an interface: 1. Use Interface to specify all CoS configurable interfaces. 2. Use Interface Trust Mode to specify whether to trust a particular packet marking at ingress. Interface Trust Mode - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 406
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Interface Queue Configuration Use the Interface Queue Configuration page to define what a particular queue does by configuring switch egress queues. User-configurable parameters control the amount of bandwidth used by the - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 407
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual To configure CoS queue settings for an interface: 1. Select the check box next to the port or LAG to configure. You can select multiple ports and LAGs to apply the same setting to the selected interfaces. Select the check - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 408
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 1. Class - Create classes and define class criteria. 2. Policy - Create policies, associate classes with policies, and define policy statements. 3. Service - Add a policy to an inbound interface Packets are classified and - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 409
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual DiffServ Wizard The DiffServ Wizard enables DiffServ on the switch by creating a traffic class, adding the traffic class to a policy, and then adding the policy to the ports selected on DiffServ Wizard page. The DiffServ - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 410
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual To display the DiffServ Wizard page, click QoS DiffServ DiffServ Wizard. 1. Use Traffic Type to define the DiffServ Class. Traffic type options: VOIP, HTTP, FTP, Telnet, and Every. 2. Ports displays the ports which can - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 411
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Auto VoIP Configuration To display the Auto VoIP Configuration page, click QoS DiffServ Auto VoIP. 1. Interface - Specifies the Auto VoIP configurable interfaces. 2. Use Auto VoIP Mode to enable or disable the Auto - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 412
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Basic From the Basic link, you can access the following pages: • DiffServ Configuration on page 412 DiffServ Configuration Packets are filtered and processed based on defined criteria. The filtering criteria is defined by - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 413
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 5-75. Field DiffServ Admin Mode Class table Class Rule table Policy table Policy Instance table Policy Attributes table Service table Description The options mode for DiffServ. The default value is 'enable'. While - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 414
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Advanced • Diffserv Configuration on page 414 • Class Configuration on page 416 • Policy Configuration on page 420 • Service Interface Configuration on page 424 • Service Statistics on page 425 Diffserv Configuration - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 415
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual To configure the global DiffServ mode: 1. Select the administrative mode for DiffServ: • Enable. Differentiated Services are active. • Disable. The DiffServ configuration is retained and can be changed, but it is not - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 416
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Class Configuration Use the Class Configuration page to add a new DiffServ class name, or to rename or delete an existing class. The page also allows you to define the criteria to - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 417
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual To configure the class match criteria: 1. Click the class name for an existing class. The class name is a hyperlink. The following figure shows the configuration fields for the class. Chapter 5. Configuring Quality of - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 418
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 2. Class Name - Displays the name for the configured DiffServ class. 3. Class Type - Displays the DiffServ class type. Options: • All Only when a new class is created, this field is a selector field. After class creation - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 419
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual • Precedence Value -This lists the keywords for the IP Precedence value in the range 0 to 7. • IP ToS - Configure the IP ToS field: • ToS Bits - This is the Type of Service octet value in the range 00 to ff to compare - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 420
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Policy Configuration Use the Policy Configuration page to associate a the specified Policy, from which one can be selected. This list is automatically updated as a new class is added to or removed from the policy. This - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 421
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual To configure the policy attributes: 1. Click the name of the policy. The policy name is a hyperlink. The following figure shows the configuration fields for the policy. Chapter 5. Configuring Quality of Service | 421 - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 422
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 2. Select the queue to which packets will of this policy-class will be assigned. This is an integer value in the range 0 to 7. 3. Configure IP DSCP • IP Precedence selected. The default is ' Configuring Quality of Service - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 423
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual • Send - These packets are presented unmodified by DiffServ to the system forwarding element. • Mark IP Precedence - These packets are marked by DiffServ with the specified IP Precedence value before being presented to - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 424
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Service Interface Configuration Use the Service Interface Configuration page to activate a policy on an interface. To display the page, click QoS DiffServ Advanced Service Interface Configuration. To configure - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 425
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Service Statistics This screen displays class-oriented statistical information for the policy, which is specified by the interface and direction. The 'Member Classes' drop down list - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 426
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual The following table describes the information available on the Service Statistics page. Table 5-79. Field Interface Direction Policy Name Operational Status Member Classes Offered Packets/Octets Discarded Packets/Octets - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 427
450 • Port Authentication on page 466 • Traffic Control on page 481 • Control on page 496 • Configuring Access Control Lists on page 524 Management Security Settings From the Management Security Settings page, you can configure the login password, Remote Authorization Dial-In User Service (RADIUS - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 428
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Local User From the Local User link, you can access the following pages: • User Management on page 428 • User Password Configuration on page 430 User Management By default, two user accounts exist: • admin, with 'Read/ - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 429
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual To display the User Management page, click Security Management Security Local User User Management. 1. Use User Name to enter the name you want to give to the new account. (You can only enter data in this field when - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 430
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual User Password Configuration To display the User Password Configuration page, click Security Management Security Local User User Password Configuration. 1. Use Password Minimum Length to specify the minimum character - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 431
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Enable Password Configuration This page prompts you to change the Privileged EXEC password. Passwords are a maximum of 64 alphanumeric characters. The password is case sensitive. To display the Enable Password - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 432
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Line Password Configuration To display the Line Password Configuration page, click Security Management Security Line Password. 1. Use Console Password to enter the Console password. Passwords are a maximum of 64 - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 433
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual RADIUS RADIUS servers provide additional security for networks. The RADIUS server maintains a user database, which contains per-user authentication information. The switch passes information to the configured RADIUS server - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 434
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual To configure to enable or disable RADIUS attribute 4. Default value is Disable. This is an optional field and IP address value in the format (xx.xx.xx.xx). Table 6-81. Field Current Server Address Number of Configured - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 435
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual RADIUS Server Configuration Use the RADIUS Server Configuration page to view and configure various settings for the current RADIUS server configured on the system. To access the RADIUS Server Configuration page, click - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 436
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual The following table describes the RADIUS server statistics available on the page. Use the buttons at the bottom of the page to perform the following - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 437
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 6-83. Field Unknown Types Packets Dropped Description The number of RADIUS packets of unknown type which were received from this server on the authentication port. The number of RADIUS packets received from this - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 438
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Accounting Server Configuration Use the RADIUS Accounting Server Configuration page to view and configure various settings for one or more RADIUS accounting servers on the network. To access the RADIUS Accounting Server - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 439
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual The following table describes RADIUS accounting server statistics server. Displays the number of RADIUS packets received on the accounting port from this server. Displays the number of malformed RADIUS Accounting-Response - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 440
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Configuring TACACS+ TACACS+ provides a centralized user management system, while still retaining consistency with RADIUS and other authentication processes. TACACS+ provides the following services: • Authentication: - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 441
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual TACACS+ Configuration The TACACS+ Configuration page contains the TACACS+ settings for communication between the switch and the TACACS+ server you configure via the inband management port. To display the TACACS+ - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 442
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual TACACS+ Server Configuration Use the TACACS+ Server Configuration page to configure up to five TACACS+ servers with which the switch can communicate. To display the TACACS+ Server Configuration page, click Security - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 443
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Authentication List Configuration The Authentication List folder validate switch or port access for the users associated with the list. The pre-configured users, admin and guest, are assigned to a pre-configured list named - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 444
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 1. List Name - If you the switch. 9. Click DELETE to remove the selected authentication login list from the configuration. The delete will fail if the selected login list is assigned to any user (including the default user - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 445
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Enable Authentication List You use this page to configure enable lists. A enable list specifies the authentication method(s) you want to be used to validate privileged EXEC access for the users associated with the list. - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 446
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 1. List Name - If you are creating a new Click ADD to add a new login list to the switch. 8. Click DELETE to remove the selected authentication enable list from the configuration. You can only use this button if you have - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 447
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Dot1x Authentication List You use this page to configure dot1x lists. A dot1x list specifies the authentication method(s) you want to be used to validate port access for the users associated with the list. Only one dot1x - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 448
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual HTTP Authentication List You use this page to configure HTTP lists. A HTTP list specifies the authentication method(s) you want used to validate switch or port access through HTTP. To display the HTTP Authentication List - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 449
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual HTTPS Authentication List You use this page to configure HTTPS lists. A login list specifies the authentication method(s) you want used to validate switch or port access through HTTPS for the users associated with the list - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 450
Secure HTTP access to the ProSafe® Managed Switches management interface. The Security Access tab contains the following folders: • HTTP on page 451 • HTTPS Configuration on page 453 • SSH on page 458 • Telnet on page 462 • Console Port on page 464 • Denial of Service on page 465 450 | Chapter - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 451
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual HTTP From the HTTP link, you can access the following pages: • HTTP Configuration on page 451 HTTP Configuration To access the switch over a web you must first configure it with IP information (IP address, subnet mask, and - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 452
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual To access the HTTP Configuration page, click Security > Access> HTTP HTTP Configuration. To configure the HTTP server settings: 1. Use HTTP Access to specify whether the switch may be accessed from a web browser. If you - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 453
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual HTTPS From the HTTPS link, you can access the following pages: • HTTPS Configuration on page 453 • Certificate Management on page 455 • Certificate Download on page 456 HTTPS Configuration Secure HTTP enables the - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 454
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual To configure HTTPS settings: 1. Use HTTPS Admin Mode to Enable or Disable the Administrative Mode of Secure HTTP. The currently configured value is shown when the web page is displayed. The default value is Disable. You - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 455
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Certificate Management Use this menu to generate or delete certificates. To display the Certificate Management page, click Security Access > HTTPS HTTPS Certificate Management. 1. Use None to specify there is no - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 456
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Certificate Download Use this menu to transfer a certificate file to the switch. For the Web server on the switch to accept HTTPS connections from a management station, the Web server needs a public key certificate. You - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 457
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual To configure the certificate download settings of the TFTP/SFTP/SCP Server Address field. The factory default is IPv4. 4. Use Server Address to enter the IP address of the server in accordance with the format indicated - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 458
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual SSH From the SSH link, you can access the following pages: • SSH Configuration on page 458 • Host Keys Management on page 460 • Host Keys Download on page 461 SSH Configuration To display the SSH Configuration page, click - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 459
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 1. Use SSH Admin Mode to Enable or Disable the administrative mode of SSH. The currently configured value is shown when the web page is displayed. The default value is Disable. 2. Use SSH Version 1 to Enable or Disable - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 460
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Host Keys Management Use this menu to generate or delete RSA and DSA keys. To display the Host Keys Management page, click Security Access > SSH Host Keys Management. 1. Host Keys Management - None is the default - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 461
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Host Keys Download Use this menu to transfer a file to or from the switch. To TFTP/SFTP/SCP Server Address field. The factory default is IPv4. 4. Use Server Address to enter the IP address of the server in accordance with - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 462
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Telnet To display the Telnet page, click Security List page under Management Security. 1. Use Login Authentication List to specify which authentication list to use when you login through telnet. The default value is - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 463
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Inbound Telnet Configuration This page regulates session is logged off. You may enter any number from 1 to 160. The factory default is 5. 3. Use Maximum Number of Sessions to select how many simultaneous telnet sessions - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 464
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Console Port To display the Console Port page, click Security Access > Console Port. 1. Use Serial Port Login Timeout (minutes) to specify how many minutes of inactivity should occur on a serial port connection before - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 465
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Denial of Service To display the Denial of Service page, click Security Access > Denial of Service. Chapter 6. Managing Device Security | 465 - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 466
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 1. Use Denial of Service Min TCP Header Size to specify the Min TCP Hdr Size allowed. If DoS TCP Fragment is enabled, the switch will drop these packets: • First TCP fragments that has a TCP payload - IP_Payload_Length - - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 467
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual The 802.1X network has three components: • Authenticators - Specifies the port that is authenticated before permitting system access. • Supplicants - Specifies the host connected to the authenticated port requesting access - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 468
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 802.1X Configuration Use the 802.1X Configuration page to enable or disable port access control on the system. To display the 802.1X Configuration page, click Security Port Authentication Basic 802.1X Configuration. - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 469
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual To configure global 802.1X settings: 1. Select the appropriate radio button in the Port Based Authentication State field to enable or disable 802.1X administrative mode on the switch. • Enable. Port-based authentication - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 470
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Advanced From the Advanced link, you can access the following pages: • 802.1X Configuration on page 470 • Port Authentication on page 471 • Port Summary on page 476 802.1X Configuration Use the 802.1X Configuration page to - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 471
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Port Authentication Use the Port Authentication page to enable and configure port access control on one or more ports. To access the Port Authentication page, click Security Port Authentication > Advanced Port - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 472
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 472 | Chapter 6. Managing Device Security - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 473
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual To configure 802.1X settings for the port: 1. Select the check box next to the port to configure. You can also select multiple check boxes to apply the same settings to the select ports, or select the check box in the - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 474
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual and 65535. A quiet period value of 0 means that the authenticator state machine will never acquire a supplicant. The default value is 60. Changing the value will not change the configuration the specified port. The - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 475
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual reauthentication will not be allowed. The default value is false. Changing the selection will not change the configuration to begin the reauthentication sequence on the selected port. This button is only selectable if the - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 476
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Port Summary Use the Port Summary page to view information about the port access control settings on a specific port. To access the Port Summary page, click Security Port Authentication Advanced Port Summary. The - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 477
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 6-94. Field Operating Control Mode Reauthentication Enabled Control Direction Protocol Version PAE Capabilities Authenticator PAE State Description This field indicates the control mode under which the port is - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 478
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 6-94. Field Backend not configurable. Possible values are: • "Radius" • "Unauth" • "Default" • "Not Assigned" This field displays if key transmission is enabled on the selected port. This is not a configurable field - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 479
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 6-94. Field Port Status Port Method Description This field shows the authorization status of the specified port. The possible values are 'Authorized', 'Unauthorized' and 'N/A'. If the port is in detached state, the - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 480
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Client Summary To access the Client Summary page, click Security Port Authentication Advanced Client Summary. Table 6-95. Field Port User Name Supplicant Mac Address Session Time Filter ID Vlan ID Vlan Assigned - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 481
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Traffic Control From the Traffic Control link, you can configure MAC Filters, Storm Control, Port Security, and Protected Port settings. To display the page, click the Security Traffic Control tab. The Traffic Control - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 482
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual To configure MAC filter settings: 1. Select Create Filter from the MAC Filter menu. a. This is the list of MAC address and VLAN ID pairings for all configured filters. To change the port mask(s) for an existing filter, - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 483
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual MAC Filter Summary Use the MAC Filter Summary page to view the MAC filters that are configured on the system. To display the MAC Filter Summary page, click Security Traffic Control> MAC Filter MAC Filter Summary. The - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 484
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Port Security The Port Security folder contains links to the following features: • Port Security Configuration on page 484 • Port Security Interface Configuration on page 486 • Dynamic MAC Address on page 488 • Static MAC - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 485
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual The Port Security Violation table shows information about violations that occurred on ports that are enabled for port security. The following table describes the fields in the Port Security Violation table. Table 6-97. - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 486
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Port Security Interface Configuration A MAC address can be defined as allowable by one of two methods: dynamically or statically. Both methods are used concurrently when a port is locked. Dynamic locking implements a first - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 487
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual To configure port security settings: 1. Port - Selects the interface to be configured. 2. Select the check box next to the port or LAG to configure. Select multiple check boxes to apply the same setting to all selected - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 488
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Dynamic MAC Address Use the Dynamic MAC Address page to convert a dynamically learned MAC address to a statically locked address. To display the Dynamic MAC Address page, click Security Traffic Control> Port Security - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 489
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Static MAC Address To display the Static MAC Address page, click Security Traffic Control> Port Security Static MAC Address. 1. Interface - Select the physical interface for which you want to display data. 2. Static - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 490
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Private Group The Private Group folder contains links to the following features: • Private Group Configuration on page 490 • Private Group Membership on page 491 Private Group Configuration To display the Private Group - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 491
® Gigabit L3 Managed Stackable Switches Software Administration Manual Private Group Membership To display the Private Group Membership page, click Security Traffic Control> Private Group Private Group Membership. 1. Use Group ID to select the Group ID for which you want to display or configure - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 492
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Protected Ports Configuration If a port is configured as protected, it does not forward traffic to any other protected port on the switch, but it will forward traffic to unprotected ports. Use the Protected Ports - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 493
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Storm Control A broadcast storm is the result of an excessive number of broadcast messages simultaneously transmitted across a network by a single port. Forwarded message responses can overload network resources and/or - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 494
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Storm Control Global Configuration To display the Storm Control Global Configuration page, click Security Traffic Control> Storm Control Storm Control Global Configuration. The following four control radio buttons - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 495
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Storm Control Interface Configuration To display the Storm Control Interface Configuration page, click Security Traffic Control> Storm Control Storm Control Interface Configuration. Chapter 6. Managing Device Security - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 496
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 6-100. Field Broadcast Storm Recovery traffic on the specified Ethernet port exceeds the configured threshold, the switch blocks (discards) the unicast traffic. The factory default is disabled. Specify the Unicast - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 497
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual • DHCP Snooping on page 497 • IP Source Guard on page 503 • Dynamic ARP Inspection on page 505 • Captive Portal on page 512 DHCP Snooping The DHCP Snooping folder contains links to - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 498
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual DHCP Snooping Global Configuration To display the DHCP Snooping Global Configuration page, click Security Control> DHCP Snooping Global Configuration. DHCP Snooping Configuration 1. Use DHCP Snooping Mode to enable or - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 499
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual DHCP Snooping Interface Configuration To display the DHCP Snooping Interface Configuration page, click Security Control> DHCP Snooping Interface Configuration. 1. Interface - Selects the interface for which data is to - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 500
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual DHCP Snooping Binding Configuration To display the DHCP Snooping Binding Configuration page, click Security Control> DHCP Snooping Binding Configuration. Static Binding Configuration 4. IP Address - Displays IP Address - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 501
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual DHCP Snooping Persistent Configuration To display the DHCP Snooping Persistent Configuration page, click Security Control> DHCP Snooping Persistent Configuration. 1. Use Store to select the local store or remote store. - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 502
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual DHCP Snooping Statistics To display the DHCP Snooping Msgs Received The number of Server messages that are dropped on an un trusted port. Click CLEAR to clear all interfaces statistics. Click REFRESH to refresh the data - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 503
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IP Source Guard The IP Source Guard folder contains links to the following features: • IP Source Guard Interface Configuration on page 503 • IP Source Guard Binding Configuration on page 504 IP Source Guard Interface - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 504
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IP Source Guard Binding Configuration To display the IP Source Guard Binding Configuration page, click Security Control> IP Source Guard Binding Configuration. Static Binding Configuration 1. Interface - Selects the - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 505
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Dynamic ARP Inspection The Dynamic ARP Inspection (DAI) folder contains links to the following features: • DAI Configuration on page 505 • DAI VLAN Configuration on page 506 • DAI Interface Configuration on page 507 • DAI - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 506
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual DAI VLAN Configuration To display the DAI VLAN Configuration page, click Security Control> Dynamic ARP Inspection DAI VLAN Configuration entries. The factory default is disable. 506 | Chapter 6. Managing Device Security - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 507
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual DAI Interface Configuration To display the DAI Interface Configuration page, click Security Control> Dynamic ARP Inspection DAI Interface Configuration to ARP inspection. The factory default is disable. 3. Use Rate - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 508
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual DAI ACL Configuration This screen shows the ARP ACLs configured. To display the DAI ACL Configuration page, click Security Control> Dynamic ARP Inspection DAI ACL Configuration. 1. Use Name to create New ARP ACL for - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 509
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual DAI ACL Rule Configuration This screen shows the Rules for selected DAI ARP ACL. To display the DAI ACL Rule Configuration page, click Security Control> Dynamic ARP Inspection DAI ACL Rule Configuration. 1. ACL Name - - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 510
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual DAI Statistics This screen shows the Statistics per VLAN. To display the DAI Statistics page, click Security Control> Dynamic ARP Inspection DAI Statistics. 510 | Chapter 6. Managing Device Security - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 511
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 6-104. Field Description VLAN destination MAC in ethernet header. Invalid IP Number of ARP packets that were dropped by DAI as the sender IP address in ARP packet or target IP address in ARP reply packet is - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 512
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Captive Portal The Captive Portal folder contains links to the following features: • Captive Portal Global Configuration on page 513 • Captive Portal Configuration on page 515 • Captive Portal Binding Configuration on page - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 513
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Captive Portal Global Configuration Using the Captive Portal Global Configuration page, you can control the administrative state of the CP feature and configure global settings that affect all captive portals configured on - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 514
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 6-105. Field Operational Status Disabled Reason CP IP Address Supported Captive Portals Configured Captive Portals Active Captive Portals System Supported Users Local Supported Users Authenticated Users Description - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 515
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Captive Portal Configuration By default, the switch has one captive portal. You can change the settings for that captive portal, and you can also create and configure up to nine additional portals. To display the Captive - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 516
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 5. Use Verification to select the mode for the CP to use to verify clients: • Guest - The user does not need to be authenticated by a database. • Local - The switch uses a local database to authenticated users. • RADIUS - - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 517
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Captive Portal Binding Configuration You can associate a configured captive portal with a specific network (SSID). The CP feature only runs on the interfaces you specify. A CP can have multiple interfaces associated with - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 518
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Captive Portal Binding Table To display the Captive Portal Binding Table page, click Security Control of authenticated users using the captive portal instance on this interface. 518 | Chapter 6. Managing Device Security - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 519
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Captive Portal Group Configuration When you click Add from the CP Group Configuration page, the screen refreshes, and you can add a new group to the User Group database. To display the Captive Portal Group Configuration - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 520
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Captive Portal User Configuration When you click Add from the CP User Configuration page, the screen refreshes, and you can add a new user to the Local User database. To display the Captive Portal User Configuration page, - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 521
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 1. User ID identifies the name of the user. 2. Use User Name to enter the name of the user. Name can contain 1 to 31 alphanumeric characters. User names once created cannot be changed/modified. 3. Set Edit Password to " - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 522
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Captive Portal Trap Flags Use this page to configure whether or not SNMP traps are sent from the Captive Portal and to specify captive portal events that will generate a trap. All CP SNMP traps are disabled by default. To - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 523
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Captive Portal Client To display the Captive Portal Client page, click Security Control> Captive Portal CP Client. Table 6-107. Field MAC Address IP address of the client Identifies the IP address of the client (if - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 524
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Configuring Access Control Lists Access identify protocols, source, and destination IP and MAC addresses, and other packet-matching criteria. Finally, use the ID number to assign the ACL to a port or to a LAG. The Security - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 525
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual To display the MAC ACL page, click Security ACL > Basic > MAC ACL. The MAC ACL table displays the number of ACLs currently configured in the switch and the maximum number of ACLs that can be configured. The current size - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 526
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual MAC Rules Use the MAC Rules page to define rules for MAC-based ACLs. The access list definition includes rules that specify whether traffic matching the criteria is forwarded normally or discarded. A default 'deny all' - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 527
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual To configure MAC ACL rules: 1. From the ACL Name field, specify the existing MAC ACL to which the rule will apply. To set up a new MAC ACL use the "MAC Binding Table" on page 6-530. 2. To add a new rule, enter a whole - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 528
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual MAC Binding Configuration When an ACL is bound to an interface, all the rules that have been defined are applied to the selected interface. Use the MAC Binding Configuration page to assign MAC ACL lists to ACL Priorities - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 529
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 1. Select an existing MAC ACL from the ACL ID menu. You can select one and bind it to the interfaces you wanted. The packet filtering - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 530
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual MAC Binding Table Use the MAC Binding Table page to of ACL assigned to selected interface and direction. Displays the ACL Number (in case of IP ACL) or ACL Name (in case of MAC ACL) identifying the ACL assigned to selected - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 531
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Advanced The Advanced folder contains links to the following features: • IP ACL on page 531 • IP Rules on page 533 • IP Extended Rules on page 535 • IPv6 ACL on page 538 • IPv6 Rules on page 539 • IP Binding Configuration - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 532
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual To configure an IP ACL: 1. In the IP ACL ID field, specify the ACL ID or IP ACL name. The ID is an integer in the following range: • 1-99: Creates an IP Basic ACL, which allows you to permit or deny traffic from a source - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 533
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IP Rules Use these screens to configure the rules for the IP Access Control Lists created using the IP Access Control List Configuration screen. What is shown on this screen varies depending on the current step in the rule - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 534
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual • Assign Queue ID - Specifies the hardware egress queue identifier used to handle all packets matching this ACL rule. Enter an identifying number from 0-6 in the - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 535
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IP Extended Rules Use these screens to configure the rules for the IP Access Control Lists created using the IP Access Control List Configuration screen. What is shown on this screen varies depending on the current step in - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 536
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual • Assign Queue - Specifies the hardware egress queue identifier used to handle all packets matching this IP ACL rule. Valid range of Queue Ids is 0 to 6. • Mirror Interface - Specifies the specific egress interface where - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 537
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Type field in the IP header, however each uses a different user notation. After a selection is made the appropriate value can be specified. • IP DSCP - Specify the IP DiffServ Code Point (DSCP) field. The DSCP is defined - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 538
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IPv6 ACL An IP ACL consists of a set of rules which are matched sequentially against a packet. When a packet meets the match criteria of a rule, the specified rule action (Permit/ - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 539
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IPv6 Rules Use these screens to configure the rules for the IPv6 Access Control Lists, which is created using the IPv6 Access Control List Configuration screen. By default, no specific value is in effect for any of the - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 540
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 1. Use the ACL Name pull down menu to select the IPv6 ACL for which to create or update a rule. 2. Use Rule ID to enter a whole number in the range of 1 to 12 that will be used to identify the rule. An IP configured port - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 541
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 12. Use Destination Prefix / PrefixLength to enter up to 128-bit prefix combined with prefix length to be compared to a packet's destination IP Address as a match criteria for the selected IPv6 ACL rule. Prefix length can - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 542
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IP Binding Configuration When an ACL is bound to an interface, all the rules that have been defined are applied to the selected interface. Use the IP Binding Configuration page to assign ACL lists to ACL Priorities and - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 543
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual To configure IP ACL interface bindings: 1. Select an existing IP ACL from the ACL ID menu. The packet filtering direction for ACL is Inbound, which means the IP ACL rules are applied to traffic entering the port. 2. - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 544
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IP Binding Table Use the IP Binding Table page to view or delete the IP ACL bindings. To display the IP Binding Table, click Security ACL> Advanced Binding Table. The following table describes the information - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 545
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Chapter 6. Managing Device Security | 545 - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 546
available from the Monitoring tab to view a variety of information about the switch and its ports and to configure how the switch monitors events. The Monitoring tab contains links to the following features: • Ports on page 546 • Logs on page 560 • Port Mirroring on page 571 • sFlow on page 573 - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 547
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Chapter 7. Monitoring the System | 547 - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 548
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual The following table describes the per-port statistics displayed on the screen. Use the buttons at the bottom of the page to perform the following actions: • To clear all the counters for all ports on the switch, select - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 549
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Port Detailed Statistics The Port Detailed Statistics page displays a variety of per-port traffic statistics. To access the Port Detailed page, click Monitoring Ports> Port Detailed Statistics. (Following two figures - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 550
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 550 | Chapter 7. Monitoring the System - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 551
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual The following table describes the detailed port information displayed on the screen. To view information about a different port, select the port counters. This resets all statistics for this port to the default values. • - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 552
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 7-112. Field Description Physical Mode Indicates The port speed and duplex mode. In auto-negotiation mode the duplex mode and speed are set from the auto-negotiation process. Physical Status Indicates the port - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 553
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 7-112. Field Description Packets Received 65-127 Octets The total number of packets (including bad packets) received that were between 65 and 127 octets - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 554
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 7-112. Field Description Alignment Errors The on this port when a lookup on a particular VLAN occurs while that entry in the VLAN table is being modified, or if the VLAN has not been configured. Multicast Tree - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 555
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table configured, including ethernet header, CRC, and payload. (1518 to 9216). The default maximum frame size is 1518. Total Packets Transmitted Successfully The number of frames that have been transmitted by this port - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 556
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 7-112. Field Description Total Transmit interface fails due to excessive collisions. Port Membership Discards The number of frames discarded on egress for this port due to egress filtering being enabled. - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 557
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual EAP Statistics Use the EAP Statistics page to display information about EAP packets received on a specific port. To display the EAP Statistics page, click Monitoring Ports> EAP Statistics. Chapter 7. Monitoring the - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 558
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual The following table describes the EAP statistics displayed on the screen. Use the buttons at the bottom of the page to perform the following actions: • To clear all the EAP counters for all ports on the switch, select the - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 559
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Cable Test To display the Cable Test page, click Monitoring Ports> Cable Test. 1. Interface - Indicates the interface to which the cable to be tested is connected. 2. Click Apply to perform a cable test on the selected - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 560
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 7-114. Field Cable Status Cable folders: • Buffered Logs on page 561 • Command Log Configuration on page 563 • Console Log Configuration on page 564 • SysLog Configuration on page 565 • Trap Logs on page 566 • Event - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 561
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Buffered Logs To access the Buffered Logs page, click Monitoring Logs > Buffered Logs. Buffered Log Configuration This log stores messages in memory based upon the settings for message component and severity. On - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 562
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Message Log This help message 318 of file mstp_api.c. This is the 237th message logged with system IP 0.0.0.0 and task-id 1. Format of the messages • Aug 24 05:34:05 STK0 MSTP[2110]: mspt_api.c(318) 237 %% Interface - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 563
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Command Log Configuration To access the Command Log Configuration page, click Monitoring Logs > Command Log Configuration. 1. Use Admin Mode to enable/disable the operation of the CLI Command logging by selecting the - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 564
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Console Log Configuration This allows logging to any serial device attached to the host. To access the Console Log Configuration page, click Monitoring Logs > Console Log Configuration. 1. A log that is "Disabled" shall - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 565
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual SysLog Configuration To access the SysLog Configuration page, click Monitoring Logs > Sys Log Configuration. 1. Use Admin Status to enable/disable logging to configured syslog hosts. Setting this to disable stops - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 566
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Trap Logs This screen lists the entries in the trap log. The information can be retrieved as a file by using System Utilities, Upload File from Switch. To access the Trap Logs page, click Monitoring Logs> Trap Logs. 566 - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 567
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual The following table describes the Trap Log information displayed on the screen. The page also displays information about the traps that were sent. Click Clear Counters to clear all the counters. This resets all statistics - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 568
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Event Logs This panel displays the event log, which contains error messages from the system. Event log is not cleared on a system reset. To access the Event Log page, click Monitoring Logs> Event Logs. 568 | Chapter 7. - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 569
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual The following table describes the Event Log information displayed on the screen. Use the buttons at the bottom of the page to perform the following - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 570
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Persistent Logs A persistent log is a log down entry field. 2. Behavior. A log records messages equal to or above a configured severity threshold. Select the severity option by selecting the corresponding line on the pull - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 571
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Format of the messages • Total number of Messages: Number of persistent log messages displayed on the switch. • Aug 24 05:34:05 STK0 MSTP[2110]: mspt_api.c(318) 237 %% Interface 12 transitioned to root state on message - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 572
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 572 | Chapter 7. Monitoring the System - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 573
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual To configure Port Mirroring: 1. Select the check box next to a port to configure it as a source port. • Mode - Specifies the Mode for mirroring. By default Mode is disabled. 2. Use Source Port to specify the configured - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 574
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 7-119. Field Agent Version Agent Address MIB Version: '1.3', the version of this MIB. • Organization: NETGEAR Inc. • Revision: 1.0 The IP address associated with this agent. Click REFRESH to refresh the web page - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 575
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Advanced From the Advanced link, you can access the following pages: • sFlow Agent on page 575 • sFlow Receiver Configuration on page 576 • sFlow Interface Configuration NETGEAR Inc. • Revision: 1.0 Agent Address The IP - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 576
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual sFlow Receiver Configuration To display the sFlow Receiver Configuration page, click Monitoring sFlow Advanced sFlow Receiver Configuration. 1. Receiver Index. Selects the receiver for which data is to be displayed - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 577
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual sFlow Interface Configuration sFlow agent collects statistical packet-based sampling of switched flows and sends them to the configured receivers. A data source configured the sampler configuration is set to default and the - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 578
links to the following features: • Save Configuration on page 578 • Reset on page 580 • Upload File From Switch on page 583 • Download File To Switch on page 587 • File Management on page 592 • Troubleshooting on page 595 Save Configuration The Save Configuration menu contains links to the following - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 579
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 1. Select the check box and click the APPLY button to have configuration changes you have made saved across a system reboot. All changes submitted since the previous save or system reboot will be retained by the switch. - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 580
falling back for broadcast TFTP tries. Reset The Reset menu contains links to the following options: • Device Reboot on page 580 • Factory Default on page 582 • Password Reset on page 583 Device Reboot Use the Device Reboot page to reboot ProSafe® Managed Switches. To access the Device Reboot page - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 581
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual To reboot the switch: 1. Use Reboot Unit No to select the unit to reset. Select all to run reset for all units. 2. Select the Save prior to reboot radio button and click the APPLY button to reboot the switch. Prior to - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 582
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Factory Default Use the Factory Default page to reset the system configuration to the factory default values. Note: If you reset the switch to the default configuration, the IP address is reset to 169.254.100.100, and the - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 583
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Password Reset Use the Password Reset page to reset all user passwords to defaults. To access the Password Reset page, click Maintenance Reset Password Reset. 1. Select the check box and click the APPLY button to have - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 584
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 584 | Chapter 8. Maintenance - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 585
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual To upload a file from the switch Support - Specify Tech Support to retrieve the switch information needed for trouble-shooting. The factory default are selected. 7. Use Password to enter the password for remote login to SFTP - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 586
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual HTTP File Upload To display the HTTP File buffered (in-memory) log. • Tech Support - Specify Tech Support to retrieve the switch information needed for troubleshooting. The factory default is Archive. 2. Use Local File Name - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 587
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual USB File Upload Use this menu to upload a file from the switch to . b. Use Text Configuration to specify configuration in text mode when you want to retrieve the stored configuration. The factory default is image1. 2. Use - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 588
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual File Download To display the File Download page, click Maintenance Download File Download. 1. Use File Type to specify what type of file you want to - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 589
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual • Use SSL DH Strong Encryption Parameter PEM File to specify SSL Diffie-Hellman Strong Encryption Parameter File (PEM Encoded) • License Key - Specify license key in order to support licensing features. The factory default - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 590
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual To download a file to the switch by using HTTP: 1. Use File Type to specify what type of file you want to transfer: • Archive - Specify archive (STK) code when you want to - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 591
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual • License Key - Specify license key in order to support licensing features. The factory default is Archive. 2. If you are downloading a GSM7352Sv1 or GSM7352Sv2 image (Archive), select the image on the switch to overwrite. - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 592
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual USB File Download Use this menu to download a file to the switch from a USB device. To display this page, click Maintenance Download USB File Download. 1. Use File Type to specify what type of file you want to - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 593
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual • Copy on page 593 • Dual Image Configuration on page 594 Copy To display the Copy page, click Maintenance File Management Copy. 1. Use Source Image to select the image1 or image2 as source image when copy occurs. 2. - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 594
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Dual Image Configuration The Dual Image feature allows switch to retain two images in permanent storage. The user designates one of these images as the active image to be loaded during subsequent switch restarts. This - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 595
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 8-122. Field Image Name Active Image Version Description This displays the image name for the selected unit. Displays the current active image of the - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 596
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 596 | Chapter 8. Maintenance - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 597
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual To configure the settings and ping a host on the network: 1. Use IP Address/Host Name to enter the IP address or Hostname of the station you want the switch to ping. The initial value is blank. The IP Address or Hostname - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 598
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Ping IPv6 This screen is used to send a Ping request to a specified Hostname or IPv6 address. You can use this to check whether the switch can communicate with a particular IPv6 station. Once you click the Apply button, - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 599
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Traceroute IPv4 Use this screen to tell the switch to send a TraceRoute request to a specified IP = y. To display the Traceroute IPv4 page, click Maintenance Troubleshooting Traceroute IPv4. Chapter 8. Maintenance | 599 - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 600
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual To configure the Traceroute settings and send probe packets to discover the route to a host on the network: 1. Use IP Address/Hostname to enter the IP address or Hostname of the station you want the switch to discover path - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 601
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Traceroute IPv6 Use this screen to tell the switch to send a TraceRoute request to a specified IP address or Hostname. You can use this to discover the paths packets take to a remote destination. Once you click the Apply - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 602
the following pages: • Support on page 602 • User Guide on page 603 Support Use the Support page to connect to the Online Support site at netgear.com. To access the Support page, click Help Online Help > Support. To connect to the NETGEAR support site for ProSafe® Managed Switches, click Apply - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 603
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual User Guide Use the User Guide page to access the ProSafe® Managed Switch (the guide you are now reading) that is available on the NETGEAR Website. To access the User Guide page, click Help Online Help > User Guide. To - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 604
Settings A This appendix describes the default settings for many of the NETGEAR 7000 series Managed Switch software features. Table 9. Default Settings Feature IP address Subnet mask Default gateway Protocol Management VLAN ID Minimum password length IPv6 management mode SNTP client SNTP server - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 605
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 9. Default Settings (Continued) Feature Auto Save Stacking sFlow ISDP RMON TACACS+ RADIUS SSH/SSL Telnet Denial of Service Protection Captive Portal Dot1x Authentication (IEEE 802.1X) MAC-Based Port Security Access - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 606
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 9. Default Settings (Continued) Feature LLDP LLDP-MED MAC Table Address Aging DHCP Layer 2 Relay Default VLAN ID Default VLAN Name GVRP GARP Timers Voice VLAN Guest VLAN RADIUS-assigned VLANs Double VLANs Spanning - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 607
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Table 9. Default Settings (Continued) Feature Default OSPFv3 Enabled DiffServ IPv4 Multicast Disabled IPv6 Multicast Disabled Licensing Support (GSM72xxPS and GSM73xxSv1) Appendix A. Default Settings | 607 - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 608
Examples B This appendix contains information about how to configure the following features: • "Virtual Local Area Networks (VLANs)" on page B-608 • "Access Control Lists (ACLs)" on page B-610 • "Differentiated Services (DiffServ)" on page B-613 • "802.1X" on page B-617 • "MSTP" on page - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 609
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual traffic is contained largely within the VLAN, reducing extraneous traffic and improving the efficiency of the whole network. • They are easy to manage. The addition of nodes, as well as moves and other changes, can be - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 610
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual • For the default VLAN with VLAN ID 1, specify the following members: port 7 (U) and port 8 (U). • For the VLAN with VLAN ID 10, specify the following members: port 1 (U), port 2 (U), and port 3 (T). • For the VLAN with - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 611
the traffic to a particular port. A default deny all rule is the last rule of every list. 2. Apply the access list to an interface in the inbound direction. ProSafe® Managed Switches allow ACLs to be bound to physical ports and LAGs. The switch software supports MAC ACLs and IP ACLs. MAC ACL Example - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 612
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 6, 7, and 8 and are assigned to the hardware egress queue 0, which is the default queue. All other traffic is explicitly denied on these interfaces. To allow additional traffic to enter these ports, you must add a new - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 613
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Differentiated Services (DiffServ) Standard IP-based networks are designed to provide best effort data delivery service. Best effort service blocks needed to configure DiffServ: • Class • Policy • Service (i.e., the - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 614
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual • IP Service Type octet (also known as: ToS bits, Precedence value, DSCP value) • Layer 4 protocol (TCP, UDP etc.) • Layer 4 source/destination ports • Source/destination IP configure DiffServ, you must define service - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 615
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual • Dropping - Drop a packet upon arrival. This is useful for emulating access control list operation using DiffServ, especially when DiffServ and ACL cannot co-exist on the same interface. • Marking IP DSCP or IP Precedence - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 616
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual DiffServ Example Configuration To create a DiffServ Class/Policy and attach it to a switch interface, follow these steps: 1. From the QoS Class Configuration screen, create a new class with the following settings: • Class - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 617
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual All UDP packet flows destined to the 192.12.2.0 network with an IP source address from the 192.12.1.0 network that have a Layer 4 Source port of 4567 and Destination port of 4568 from this switch on ports 7 and 8 are - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 618
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual operation of a switch's ports to be controlled in order to ensure that access to its services is only permitted by systems that are authorized to do so. Port exchange. Gigabit L3 switches support the Authenticator - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 619
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 802.1X Example Configuration This example shows how to configure the switch so that 802.1X-based authentication is required on the ports in a corporate conference room (1/0/5 - 1/0/8). These ports are available to visitors - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 620
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual MSTP Spanning Tree Protocol (STP) runs on bridged networks to help eliminate loops. If a bridge loop occurs, the network can become flooded with traffic. IEEE 802.1s Multiple Spanning Tree Protocol (MSTP) supports multiple - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 621
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual An MST Region comprises of one or more MSTP Bridges with the same MST Configuration Identifier, using the same MSTIs, and which have no Bridges attached that cannot receive and transmit MSTP BPDUs. The MST Configuration - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 622
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Ports 1/0/1 - 1/0/5 Connected to Hosts Ports 1/0/1 - 1/0/5 Connected to Hosts Ports 1/0/6 - 1/0/8 Connected to Switch 2 and 3 1/0/1 - 1/0/5 Switch 1 Root Bridge Ports 1/0/6 - 1/0/8 Connected to Switch 1 and 3 Switch 2 - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 623
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual 7. Select ports 1/0/1 - 1/0/5 (edge ports), and select Enable from the Fast Link menu. Since the edge ports are not at risk for network loops, ports with Fast Link enabled transition directly to the Forwarding state. 8. - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 624
other antenna or transmitter. FCC Declaration Of Conformity We, NETGEAR, Inc., 350 East Plumeria Drive, San Jose, CA 95134, declare under our sole responsibility that the GSM7352S ProSafe 48+4 Gigabit Ethernet L3 Managed Stackable Switch complies with Part 15 of FCC Rules. Appendix C. Notification - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 625
to the product, unless expressly approved by NETGEAR, Inc., could void the user's right to operate the equipment. Canadian Department of Communications Radio Interference Regulations This digital apparatus, GSM7352S ProSafe 48+4 Gigabit Ethernet L3 Managed Stackable Switch, does not exceed the Class - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 626
SNTP Server 43 Standard IP ACL Example 612 STP 151 TACACS+ 440 Trap 96 VLAN 132 VLAN example 609 CoS 400 D defaults CoS 611 DES 17 Device View 14 DiffServ 407 DNS 46 download from a remote system 587 E EAP 557 F file management 592 firmware download 587 G guest VLAN configuration 619 H help, HTML - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 627
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual IEEE 802.1s 152 IEEE 802.1w 151 IEEE 802.1X 433 IGMP 172 interface LAG 201 logical 18 naming convention 18 physical 18 queue configuration 406 IP DSCP 400 Mapping 403 L LAG VLAN 201 LAGPDUs 201 LAGs 201 Membership 203 - Netgear GSM7252PS | ProSafe Managed Switch Web Management User Manual - Page 628
ProSafe® Gigabit L3 Managed Stackable Switches Software Administration Manual Port VLAN ID 139 PVID 139 628 | Index
350 East Plumeria Drive
San Jose, CA 95134
USA
October 27, 2010
202-10757-01
v1.0
ProSafeĀ® Managed Switch
Web Management User Manual