Epson SureColor S50670 User Manual - Page 155

Mode 1, Mode 2, Data Width, Printer Full Width, Printable Side Out, Printable Side

Get Epson SureColor S50670 PDF manuals and user guides View all Epson SureColor S50670 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 155 highlights

Item Parameter Heater Temperature Pre-heater/platen heater: 30 °C to 50 °C (86 °F to 122 °F) After heater: 30 °C to 55 °C (86 °F to 131 °F) Drying Time Per Pass 0 to 10sec After Heater Feed Mode 1 Mode 2 Off Additional Dryer On Off Media Suction 0 to 10 Head Movement Data Width Printer Full Width Multi-Strike Printing Roll Type Off 2 to 8 Printable Side Out Printable Side In Explanation The temperatures for the pre-, platen, and after heaters can each be adjusted separately. Select the time the print head pauses to allow drying after each pass. Choose from values between 0.0 and 10.0 seconds. The time needed for the ink to dry varies with ink density and the media used. If the ink blurs on the media, set a longer time for drying the ink. Increasing the drying time increases the time needed to print. To feed media to the after heater after printing, choose Mode 1 or Mode 2; otherwise, choose Off. If Mode 1 is selected, the portion fed for drying will not be rewound before the next job starts. Select this option if the media will be cut before the next job starts. If Mode 2 is selected, the portion fed for drying will be rewound before the next job starts, eliminating unnecessary margin. Select this option if multiple jobs will be printed consecutively. Select On to enable, or Off to disable, the optional additional print drying system. Note that even when On is selected, the additional print drying system will turn off with the heaters when the Heat Off Timer expires. The additional print drying system will turn back on when the heaters resume operation. See "Printer Setup Menu" on page 156. This item is displayed only when the optional additional print drying system is installed. Suction is required to maintain the correct distance between the media and the print head; the amount needed varies with the type of media. Excessive suction can increase the gap between the print head and thin or flexible media, potentially reducing print quality or preventing the media feeding normally. In such cases, you will need to lower media suction. The suction power is weakened when the parameter is lowered. Choose the range in which the print head moves during printing. Data Width restricts print head movement to the printed area. Restricting the extent of print head movement increases print speed. If Printer Full Width is selected, the print head will move the full width of the largest media supported by the printer. Select this option for more even print results with less variation. Choose the number of times each line is printed. Choose Printable Side Out or Printable Side In according to how the media is rolled. Using the Control Panel Menu 155

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
Using the Control Panel Menu
155
Heater Temperature
Pre-heater/platen heater:
30 °C to 50 °C (86 °F to
122 °F)
After heater: 30 °C to 55 °C
(86 °F to 131 °F)
The temperatures for the pre-, platen, and after heaters can each be
adjusted separately.
Drying Time Per Pass
0 to 10sec
Select the time the print head pauses to allow drying after each pass.
Choose from values between 0.0 and 10.0 seconds. The time needed for
the ink to dry varies with ink density and the media used. If the ink blurs
on the media, set a longer time for drying the ink.
Increasing the drying time increases the time needed to print.
After Heater Feed
Mode 1
To feed media to the after heater after printing, choose
Mode 1
or
Mode 2
; otherwise, choose
Off
.
If
Mode 1
is selected, the portion fed for drying will not be rewound
before the next job starts. Select this option if the media will be cut
before the next job starts.
If
Mode 2
is selected, the portion fed for drying will be rewound before
the next job starts, eliminating unnecessary margin. Select this option if
multiple jobs will be printed consecutively.
Mode 2
Off
Additional Dryer
On
Select
On
to enable, or
Off
to disable, the optional additional print
drying system. Note that even when
On
is selected, the additional print
drying system will turn off with the heaters when the Heat Off Timer
expires. The additional print drying system will turn back on when the
heaters resume operation. See
“Printer Setup Menu” on page 156.
This item is displayed only when the optional additional print drying
system is installed.
Off
Media Suction
0 to 10
Suction is required to maintain the correct distance between the media
and the print head; the amount needed varies with the type of media.
Excessive suction can increase the gap between the print head and thin
or flexible media, potentially reducing print quality or preventing the
media feeding normally. In such cases, you will need to lower media
suction. The suction power is weakened when the parameter is
lowered.
Head Movement
Data Width
Choose the range in which the print head moves during printing.
Data Width
restricts print head movement to the printed area.
Restricting the extent of print head movement increases print speed.
If
Printer Full Width
is selected, the print head will move the full width
of the largest media supported by the printer. Select this option for
more even print results with less variation.
Printer Full Width
Multi-Strike Printing
Off
Choose the number of times each line is printed.
2 to 8
Roll Type
Printable Side Out
Choose
Printable Side Out
or
Printable Side In
according to how the
media is rolled.
Printable Side In
Item
Parameter
Explanation