HP Integrity Superdome SX2000 HP Insight Manager WBEM Provider Events Referenc - Page 10

Event ID Event Severity 26 Warning 730 Error 720 Warning 732 Warning 722 Warning 757 Warning 758 Warning 731 Error 726 Error 733 Warning 734 Error Event Description The server's built-in sensors have detected an open chassis door. Probable Cause: The server has detect that the chassis door or other access panel is not securely closed. Recommended Action: Close any open panels or chassis doors. WBEM EventID: 127. WBEM ProviderName: SEL02_IndicationProvider. The BMC firmware did not detect the system firmware boot. Probable Cause: Possible Causes: 1. Bad System Firmware image in ROM 2. Power not reaching processors 3. Processor is in reset or is not properly seated in system 4. An unsupported processor was inserted in system 5. Communication with BMC is impaired. Recommended Action: To correct the problem, try the following: 1. Validate that processors are supported in this system. 2. Verify that processors are seated properly in system. 3. Check if system has booted (only a communication problem. - future events will also be lost.) 4. Attempt a system reset, INIT, and/or A/C cycle to clear the problem. 5. Update system firmware again if necessary. WBEM EventID: 132. WBEM ProviderName: SEL02_IndicationProvider. Power supply failure. Probable Cause: The system has detected that one of the power supplies has failed. Recommended Action: The power cable has been disconnected. Reconnect, or The power supply has failed. Contact your HP support representative to check the power supply. WBEM EventID: 137. WBEM ProviderName: SEL02_IndicationProvider. The power supply sensors detect a possible problem. Probable Cause: The power supply fan(s) is slowing. Recommended action: Check power supply fan(s). WBEM EventID: 138. WBEM ProviderName: SEL02_IndicationProvider. Power supply AC lost. Probable Cause: The power supply has lost its A/C source. The power supply is not connected to a working A/C power source. Recommended Action: Verify that the plug is connected to the power supply, and to a working power source. The AC voltage to the power supply was lost or is out of range.. Probable Cause: The AC voltage was lost, or is the wrong range for the system. Recommended Action: Verify the power supply is plugged in to the proper voltage for the system. WBEM EventID: 140. WBEM ProviderName: SEL02_IndicationProvider. The power supply AC voltage is out of range. Probable Cause: The AC voltage is connected to the power supply, but it is not the voltage range required for the system. Recommended Action: Connect the power supply to the proper voltage range. WBEM EventID: 141. WBEM ProviderName: SEL02_IndicationProvider. A/C Power failed, disconnected, or out of range. Probable Cause: The input power to the supply has failed or gone out of range. Or the input cord has been disconnected. Recommended Action: Check the power cord or source voltage. WBEM EventID: 154. WBEM ProviderName: SEL02_IndicationProvider. Power failure in power supply. Probable Cause: Indicates a failure with the AC power source that is connected to one of the redundant power supply units. Recommended Action: Check the power cord or source voltage. WBEM EventID: 155. WBEM ProviderName: SEL02_IndicationProvider. Cooling unit warning. Probable Cause: The Cooling Unit may be running properly now, but it was detected in a degraded state. It may need to be replaced in the future. Recommended Action: Continue to monitor unit and contact HP support to determine appropriate action. WBEM EventID: 157. WBEM ProviderName: SEL02_IndicationProvider. Cooling unit failure. Probable Cause: A cooling unit has failed. Recommended Action: Replace the indicated cooling unit. WBEM EventID: 158. WBEM ProviderName: SEL02_IndicationProvider. 10 WBEM Provider Event Tables