HP Integrity Superdome SX2000 HP Insight Manager WBEM Provider Events Referenc - Page 24

Parity error in Reg FIFO Internal parity error. Probable Cause: Parity error in Reg

Get HP Integrity Superdome SX2000 PDF manuals and user guides View all HP Integrity Superdome SX2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Event ID Event Severity 5407 Error 5408 Error 5411 Error 5416 Error 5417 Error 5418 Error 5419 Warning 5420 Error 5432 Error 5438 Warning 5440 Warning 5442 Error 5443 Error 5444 Error 5445 Error 5446 Error Event Description Crossbar slices are out of rev with each other. Probable Cause: Bad hardware configuration, different revisions of crossbars are installed. Recommended Action: Check crossbar revisions and ensure all installed crossbar revisions are the same. Replace the crossbar that is not in rev with the others. WBEM EventID: 363. WBEM ProviderName: FPL_IndicationProvider. Crossbar slices are configured poorly. Probable Cause: Fatal configuration. Reconfigure the hardware. WBEM EventID: 364. WBEM ProviderName: FPL_IndicationProvider. A CPU has taken over for the monarch CPU. Probable Cause: The previous monarch may be suspect. WBEM EventID: 365. WBEM ProviderName: FPL_IndicationProvider. Sram cannot be used on the cell. Probable Cause: SRAM cannot be located or used on the cell board. Replace the cell board. WBEM EventID: 366. WBEM ProviderName: FPL_IndicationProvider. The dillon hardware cannot be located. Probable Cause: ROM is corrupt. Replace the rom or reprogram flash. WBEM EventID: 367. WBEM ProviderName: FPL_IndicationProvider. A required piece of PDH bus hardware cannot be contacted. Probable Cause: Verify all connections of PDH bus components or replace the cell board. WBEM EventID: 368. WBEM ProviderName: FPL_IndicationProvider. Error: PCI Buses are configured for multiple speeds. Probable Cause: A PCI card is configured with mixed speeds. Recommended Action: Correct the configuration problem. WBEM EventID: 2420. WBEM ProviderName: FPL_IndicationProvider. The bus depth was exceeded during IO probing. Probable Cause: Too many PCI bridge cards are configured in single PCI segment mode. Recommended Action: Reconfigure PCI cards and remove some of the bridge devices. WBEM EventID: 2421. WBEM ProviderName: FPL_IndicationProvider. A Timeout occurred during RI initialization. The CSR is in the data field. The alert level will vary. Probable Cause: Hardware problem such as cable connect error or bad cables. Recommended Action: Correct the hardware problem and re-boot. WBEM EventID: 2422. WBEM ProviderName: FPL_IndicationProvider. SuperIO has been detected in slot. Probable Cause: SuperIO has been detected in the PCI slot. Recommended Action: No action required, information only. WBEM EventID: 2423. WBEM ProviderName: FPL_IndicationProvider. IO Link software error was corrected. Probable Cause: IO link error was detected and corrected. Recommended Action: No action required, information only. WBEM EventID: 372. WBEM ProviderName: FPL_IndicationProvider. Parity error in Reg FIFO Internal parity error. Probable Cause: Parity error in Reg FIFO. Recommended Action: Replace bad hardware. WBEM EventID: 374. WBEM ProviderName: FPL_IndicationProvider. TLB Fetch timeout. Probable Cause: SBA TLB fetch timeout error. Recommended Action: Replace faulty hardware. WBEM EventID: 375. WBEM ProviderName: FPL_IndicationProvider. Link presence goes away, FE. Probable Cause: Link presence lost on SBA interface. Recommended Action: Replace faulty hardware. WBEM EventID: 376. WBEM ProviderName: FPL_IndicationProvider. Elroy to REO parity error on command, rope will go fatal. Probable Cause: Bad hardware. Recommended Action: Replace I/O chassis. WBEM EventID: 377. WBEM ProviderName: FPL_IndicationProvider. Access to invalid TLB entry Requesting rope fatal. Probable Cause: An IO device is requesting access to an invalid TLB entry. Recommended Action: Driver problem debug driver. WBEM EventID: 378. WBEM ProviderName: FPL_IndicationProvider. 24 WBEM Provider Event Tables

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
Event Description
Event
Severity
Event ID
Crossbar slices are out of rev with each other. Probable Cause: Bad hardware
configuration, different revisions of crossbars are installed. Recommended Action:
Check crossbar revisions and ensure all installed crossbar revisions are the same.
Replace the crossbar that is not in rev with the others. WBEM EventID: 363. WBEM
ProviderName: FPL_IndicationProvider.
Error
5407
Crossbar slices are configured poorly. Probable Cause: Fatal configuration.
Reconfigure the hardware. WBEM EventID: 364. WBEM ProviderName:
FPL_IndicationProvider.
Error
5408
A CPU has taken over for the monarch CPU. Probable Cause: The previous monarch
may be suspect. WBEM EventID: 365. WBEM ProviderName: FPL_IndicationProvider.
Error
5411
Sram cannot be used on the cell. Probable Cause: SRAM cannot be located or used
on the cell board. Replace the cell board. WBEM EventID: 366. WBEM ProviderName:
FPL_IndicationProvider.
Error
5416
The dillon hardware cannot be located. Probable Cause: ROM is corrupt. Replace
the rom or reprogram flash. WBEM EventID: 367. WBEM ProviderName:
FPL_IndicationProvider.
Error
5417
A required piece of PDH bus hardware cannot be contacted. Probable Cause: Verify
all connections of PDH bus components or replace the cell board. WBEM EventID:
368. WBEM ProviderName: FPL_IndicationProvider.
Error
5418
Error: PCI Buses are configured for multiple speeds. Probable Cause: A PCI card is
configured with mixed speeds. Recommended Action: Correct the configuration
problem. WBEM EventID: 2420. WBEM ProviderName: FPL_IndicationProvider.
Warning
5419
The bus depth was exceeded during IO probing. Probable Cause: Too many PCI
bridge cards are configured in single PCI segment mode. Recommended Action:
Reconfigure PCI cards and remove some of the bridge devices. WBEM EventID: 2421.
WBEM ProviderName: FPL_IndicationProvider.
Error
5420
A Timeout occurred during RI initialization. The CSR is in the data field. The alert
level will vary. Probable Cause: Hardware problem such as cable connect error or
bad cables. Recommended Action: Correct the hardware problem and re-boot. WBEM
EventID: 2422. WBEM ProviderName: FPL_IndicationProvider.
Error
5432
SuperIO has been detected in slot. Probable Cause: SuperIO has been detected in the
PCI slot. Recommended Action: No action required, information only. WBEM
EventID: 2423. WBEM ProviderName: FPL_IndicationProvider.
Warning
5438
IO Link software error was corrected. Probable Cause: IO link error was detected
and corrected. Recommended Action: No action required, information only. WBEM
EventID: 372. WBEM ProviderName: FPL_IndicationProvider.
Warning
5440
Parity error in Reg FIFO Internal parity error. Probable Cause: Parity error in Reg
FIFO. Recommended Action: Replace bad hardware. WBEM EventID: 374. WBEM
ProviderName: FPL_IndicationProvider.
Error
5442
TLB Fetch timeout. Probable Cause: SBA TLB fetch timeout error. Recommended
Action: Replace faulty hardware. WBEM EventID: 375. WBEM ProviderName:
FPL_IndicationProvider.
Error
5443
Link presence goes away, FE. Probable Cause: Link presence lost on SBA interface.
Recommended Action: Replace faulty hardware. WBEM EventID: 376. WBEM
ProviderName: FPL_IndicationProvider.
Error
5444
Elroy to REO parity error on command, rope will go fatal. Probable Cause: Bad
hardware. Recommended Action: Replace I/O chassis. WBEM EventID: 377. WBEM
ProviderName: FPL_IndicationProvider.
Error
5445
Access to invalid TLB entry Requesting rope fatal. Probable Cause: An IO device is
requesting access to an invalid TLB entry. Recommended Action: Driver problem -
debug driver. WBEM EventID: 378. WBEM ProviderName: FPL_IndicationProvider.
Error
5446
24
WBEM Provider Event Tables