HP Integrity Superdome SX2000 HP Insight Manager WBEM Provider Events Referenc - Page 73
Master MP failure. Slave MP has taken control. WBEM EventID: 2484. WBEM
View all HP Integrity Superdome SX2000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 73 highlights
Event ID Event Severity 9879 Warning 9896 Error 10060 Warning 10061 Warning 10062 Warning 10063 Warning 10064 Warning 10065 Warning 10068 Warning 10069 Warning 10070 Warning 10071 Warning 10072 Warning 10073 Warning 10103 Warning 10104 Warning 10105 Warning 10115 Warning Event Description CPU deconfigured while getting an address for a CPU internal register within a buffer from the CPU abstraction layer. Probable Cause: internal error. Recommended Action: the CPU will be deconfigured. If the error persists after a powercycle, contact HP Support. WBEM EventID: 1857. WBEM ProviderName: FPL_IndicationProvider. Not enough error free memory to run late sefltests. Probable Cause: Due to excessive memory subsystem or DIMM errors, the late selftests could not be run. DIMMs or memory extenders have caused excessive errors and will need to be replaced. Consult the memory test events regarding memory errors or view the Page Deallocation Table from BCH. WBEM EventID: 1860. WBEM ProviderName: FPL_IndicationProvider. The left cell latch is open. WBEM EventID: 2413. WBEM ProviderName: FPL_IndicationProvider. Right ejector latch is open. Probable Cause: The right ejector latch is open. Recommended Action: Close the right ejector latch on the specified cell. WBEM EventID: 2412. WBEM ProviderName: FPL_IndicationProvider. The optical emitters on the cell latch sensors are not functioning. Probable Cause: There is a hardware failure. Recommended Action: The cell board must be repaired or replaced. WBEM EventID: 2411. WBEM ProviderName: FPL_IndicationProvider. The vrm on the specified cell is reporting a voltage fault. Probable Cause: The specified vrm is reporting a fault. Recommended Action: Replace the specified VRM. The datafield contains the physical location. Byte 16 is the cabinet, byte 13 is the cell slot, and byte 11 is the vrm slot. The vrm slot in byte 11 matches the vrm number silkscreened on the cell board. WBEM EventID: 2485. WBEM ProviderName: FPL_IndicationProvider. The vrm on the specified cell is reporting a temperature fault. WBEM EventID: 2486. WBEM ProviderName: FPL_IndicationProvider. The rail on a cell is reporting a fault. WBEM EventID: 2487. WBEM ProviderName: FPL_IndicationProvider. A I/O backplane vrm is reporting a voltage fault. WBEM EventID: 2488. WBEM ProviderName: FPL_IndicationProvider. A I/O backplane power brick is reporting a voltage fault. WBEM EventID: 2489. WBEM ProviderName: FPL_IndicationProvider. A I/O backplane vrm is reporting a temperature fault. WBEM EventID: 2490. WBEM ProviderName: FPL_IndicationProvider. A I/O backplane power brick is reporting a temperature fault. WBEM EventID: 2491. WBEM ProviderName: FPL_IndicationProvider. A I/O backplane vrm rail is reporting a fault. WBEM EventID: 2492. WBEM ProviderName: FPL_IndicationProvider. A I/O backplane power brick is reporting a rail fault. WBEM EventID: 2493. WBEM ProviderName: FPL_IndicationProvider. The specified system backplane vrm is reporting a module voltage fault. WBEM EventID: 2495. WBEM ProviderName: FPL_IndicationProvider. The specified system backplane vrm is reporting a temperature fault. WBEM EventID: 2496. WBEM ProviderName: FPL_IndicationProvider. The specified system backplane rail is reporting a fault. WBEM EventID: 2497. WBEM ProviderName: FPL_IndicationProvider. Master MP failure. Slave MP has taken control. WBEM EventID: 2484. WBEM ProviderName: FPL_IndicationProvider. Platform Events 73