HP Integrity Superdome SX2000 HP Insight Manager WBEM Provider Events Referenc - Page 18
I/O SBA clear error failed. Probable Cause: I/O chipset failure. Recommended Action
View all HP Integrity Superdome SX2000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 18 highlights
Event ID Event Severity 5136 Warning 5137 Warning 5138 Warning 5139 Warning 5140 Warning 5141 Warning 5142 Warning 5143 Warning 5144 Warning 5145 Warning 5146 Warning 5147 Warning 5148 Warning 5149 Warning 5150 Warning 5152 Error Event Description I/O host bridge inaccessible because rope reset failed to complete. Probable Cause: I/O CEC failure. Recommended Action: Contact your HP representative to check the I/O CEC. WBEM EventID: 276. WBEM ProviderName: FPL_IndicationProvider. Insufficient power to turn on PCI slot. Probable Cause: The power budget for the IO subsystem has been exceeded. Recommended Action: The IO config in the system is unsupported. Verify that the IO config installed in the system is one that is supported. If problem persists contact your HP representative for support. WBEM EventID: 277. WBEM ProviderName: FPL_IndicationProvider. PCI bus walk unknown error. Probable Cause: Internal firmware error. Recommended Action: Contact your HP representative to check the firmware. WBEM EventID: 278. WBEM ProviderName: FPL_IndicationProvider. PCI bus walk resources exceeded. Probable Cause: Unsupported I/O configuration. Recommended Action: Remove any unsupported I/O cards. Move the I/O card to another slot. WBEM EventID: 279. WBEM ProviderName: FPL_IndicationProvider. PCI bus unmap unknown error. Probable Cause: Internal firmware error. Recommended Action: Contact your HP representative to check the firmware. WBEM EventID: 280. WBEM ProviderName: FPL_IndicationProvider. PCIXCAP sampling error. Probable Cause: I/O host bridge failure. Recommended Action: Contact your HP representative to check the I/O host bridge. WBEM EventID: 281. WBEM ProviderName: FPL_IndicationProvider. Power monitor failed to respond. Probable Cause: BMC failure. Recommended Action: Contact your HP representative to check the BMC. WBEM EventID: 282. WBEM ProviderName: FPL_IndicationProvider. I/O rope reset failed to complete. Probable Cause: I/O CEC failure. Recommended Action: Reboot. If problem persists, contact your HP representative to check the I/O controller. WBEM EventID: 283. WBEM ProviderName: FPL_IndicationProvider. I/O SBA clear error failed. Probable Cause: I/O chipset failure. Recommended Action: Contact your HP representative to check the I/O chipset. WBEM EventID: 284. WBEM ProviderName: FPL_IndicationProvider. PCI slot has incorrect default power state. Probable Cause: The hot-plug controller has failed. Recommended Action: Contact your HP representative to check the hot-plug slot. WBEM EventID: 285. WBEM ProviderName: FPL_IndicationProvider. PCI slot power on error. Probable Cause: The I/O card is damaged or improperly inserted. Recommended Action: Replace or reseat the I/O card. WBEM EventID: 286. WBEM ProviderName: FPL_IndicationProvider. PCI slot's standby power failed. Probable Cause: I/O slot failure. Recommended Action: Reseat IO card. Replace IO card. If problem persists, contact your HP representative to check the I/O slot. WBEM EventID: 287. WBEM ProviderName: FPL_IndicationProvider. Found invalid PCIXCAP value. Probable Cause: The I/O card is damaged or improperly inserted. Recommended Action: Replace or reseat the I/O card. WBEM EventID: 288. WBEM ProviderName: FPL_IndicationProvider. Unsupported rope frequency. Probable Cause: Internal firmware error. Recommended Action: Contact your HP representative to check the firmware. WBEM EventID: 289. WBEM ProviderName: FPL_IndicationProvider. Unsupported host bridge type. Probable Cause: Firmware needs to be updated. An incorrect I/O backplane is installed. Recommended Action: Contact your HP representative to check the firmware and the I/O backplane. WBEM EventID: 290. WBEM ProviderName: FPL_IndicationProvider. Machine Check initiated. Probable Cause: A Machine Check has occurred. Recommended Action: Analyze cause of Machine Check using diag's and EFI tools. WBEM EventID: 292. WBEM ProviderName: FPL_IndicationProvider. 18 WBEM Provider Event Tables