Home » Lexmark Manuals » Laser Printers » Lexmark T652 » Manual Viewer

Lexmark T652 Service Manual - Page 53

Lexmark T652 Manual

Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

4062 Error code or message 201.01 Error contents Description/Action Possible repair actions Main drive motor assembly load error. Type 1 fuser The main drive motor assembly has failed or caused high mechanical load due to paper jam or bind. 1. Check all connections on the main drive motor assembly. 2. Check all connections on the system card assembly. 3. Replace the main drive motor assembly if problem remains. Go to "Output cover assembly removal (T650, T652, T654)" on page 4-54. Go to sensor (fuser output) late jam service check. See "Sensor (fuser output) late jam service check." on page 2-135. If problem remains, a type 2 fuser can be installed. 201.02 Sensor (fuser output) late jam. Type 1 fuser The media is late reaching the sensor (fuser output) within the specified time. 201.03 Image data did not start in time Type 1 fuser Printhead write failure 1. Check all connections on the printhead assembly 2. Check all connections on the system card assembly. 3. Replace the printhead assembly if problem remains. 4. Replace the system card assembly if problem remains. Go to "System card assembly removal (T650, T652, T654, T656)" on page 4-76. 201.04 Sensor (narrow media) late jam Type 1 fuser The expected wide media is late reaching the sensor (narrow media) within the specified time. Go to sensor (narrow media) late jam service check. See "Sensor (narrow media) late jam service check." on page 2-139. Go to sensor (narrow media) late jam service check. See "Sensor (narrow media) late jam service check." on page 2-139. Go to sensor (fuser output) late jam service check. See "Sensor (fuser output) late jam service check." on page 2-135. Go to sensor (fuser output) service check. See "Sensor (fuser output) late jam service check." on page 2-135. 201.06 Sensor (narrow media) late jam Type 1 fuser The expected wide media is late reaching the sensor (narrow media) within the specified time. 201.07 Sensor (fuser output) late jam Type 1 fuser The media is late reaching the sensor (fuser output) within the specified time. 201.25 Sensor (fuser output) area jam. Type 2 fuser The media is jammed in the sensor (fuser output) area. Diagnostic information 2-19

Section	Page
Table of contents	3
Notices and safety information	15
Laser notice	15
Laser	15
Avis relatif à l’utilisation de laser	15
Avvertenze sui prodotti laser	15
Avisos sobre el láser	16
Declaração sobre Laser	16
Laserinformatie	16
Lasermeddelelse	16
Laserilmoitus	17
Huomautus laserlaitteesta	17
Laser-notis	17
Laser-melding	17
Avís sobre el Làser	18
Lithium warning	21
Consignes de sécurité	21
Norme di sicurezza	21
Sicherheitshinweise	22
Pautas de Seguridad	22
Informações de Segurança	22
Informació de Seguretat	23
Preface	24
1. General information	25
Maintenance approach	25
Options	26
Available internal options	26
Media handling options	26
Printer configurations	27
Supported paper sizes, types, and weights	30
Tools required	32
Acronyms	33
2. Diagnostic information	35
Start	35
Confirm the installation status	36
Power-on Reset sequence	36
Entering Diagnostics mode	36
User attendance messages	37
Error code table 1	48
Service checks	160
Sensor (input) service check	160
Sensor (fuser output) service check	160
Sensor (narrow media) service check	161
Sensor (duplex input) service check	161
Sensor (duplex input) service check (external duplex only)	162
Sensor (duplex exit) service check (external duplex only)	162
Sensor (pass through) service check	163
Sensor (envelope feeder empty) service check	163
Sensor (input) late jam service check.	163
Sensor (input) lingering jam service check.	166
Sensor (input) early jam service check	167
Sensor (input) static jam service check	169
Sensor (fuser output) late jam service check.	169
Sensor (fuser output) lingering jam service check.	171
Sensor (fuser output) static jam service check	172
Sensor (narrow media) late jam service check.	173
Sensor (narrow media) static jam service check	174
Sensor (duplex input) late jam service check.	175
Sensor (duplex input) lingering jam service check.	176
Sensor (duplex input) static jam service check.	178
Sensor (pass through) late jam service check	179
Sensor (pass through) lingering jam service check.	180
Sensor (pass through) static jam service check	181
Sensor (stapler pass through) late jam service check	182
Sensor (stapler pass through) lingering jam service check	183
Sensor (stapler pass through) static jam service check	183
Sensor (output pass through) late jam service check	184
Sensor (output pass through) lingering jam service check	185
Sensor (output pass through) static jam service check	186
Sensor (mailbox empty) late jam service check	187
Sensor (mailbox empty) lingering jam service check	188
Sensor (mailbox empty) static jam service check	188
Sensor (toner empty) service check	189
NVRAM mismatch failure (950.00 through 950.29) service check	189
Image quality trouble	191
Printer Related Troubleshooting	191
Image Quality	192
Network service check	211
3. Diagnostic aids	213
Understanding the printer control panel (models T650, T652, and T654)	213
Accessing service menus (models T650, T652, and T654)	214
Diagnostics mode (models T650, T652, and T654)	215
Entering Diagnostics mode (models T650, T652, and T654)	215
Available tests	215
Exiting Diagnostics mode (models T650, T652, and T654)	217
REGISTRATION	217
PRINT TESTS	219
HARDWARE TESTS	220
DUPLEX TESTS	224
INPUT TRAY TESTS	226
OUTPUT BIN TESTS	227
StapleSmart FINISHER TESTS	230
BASE SENSOR TEST	231
PRINTER SETUP	231
EP SETUP	233
REPORTS	235
EVENT LOG	235
EXIT DIAGNOSTICS (models T650, T652, and T654)	236
Configuration menu (CONFIG MENU) (models T650, T652, and T654)	237
Entering Configuration Menu (models T650, T652, and T654)	237
Available menus	237
Maintenance page count (Maint Cnt Value)	237
Maintenance page counter reset (Reset Cnt)	238
Print quality pages (Prt Quality Pgs)	238
Reports	238
SIZE SENSING	239
Panel Menus	239
PPDS Emulation	239
Demo Mode	239
Factory Defaults	240
LES Applications	240
Energy Conserve	240
Paper Prompts	240
Env Prompts	240
Action for Prompts	240
Font Sharpening	240
Wiper Messages	240
Clear Custom Status	240
Best Speed	241
Exit Config Menu (models T650, T652, and T654)	241
Understanding the printer control panel (model T656)	241
Accessing service menus (model T656)	242
Diagnostics Menu (model T656)	243
Entering Diagnostics Menu (model T656)	243
Available tests	243
Registration (printer)	245
PRINT TESTS	247
HARDWARE TESTS	248
DUPLEX TESTS	250
INPUT TRAY TESTS	252
OUTPUT BIN TESTS	253
BASE SENSOR TEST	254
DEVICE TESTS	255
PRINTER SETUP	256
EP SETUP	257
REPORTS	259
EVENT LOG	259
Configuration menu (CONFIG MENU) (model T656)	261
Entering Configuration Menu (model T656)	261
Available menus	261
Maintenance Counter Value	261
Reset Maintenance Counter	262
Print Quality Pages	263
Reports	263
SIZE SENSING	264
Panel Menus	264
PPDS Emulation	264
Factory Defaults	266
Energy Conserve	266
Paper Prompts	267
Envelope Prompts	267
Action for Prompts	267
Jobs On Disk	267
Disk Encryption	268
Wipe Disk	269
Font Sharpening	269
Require Standby	269
LES Applications	270
Key Repeat Initial Delay	270
Key Repeat Rate	270
Wiper Message	270
Clear Custom Status	270
USB speed	271
Exit Configuration Menu (model T656)	271
Printer overview	272
Printer theory	273
Model T650 with duplex, paper path, rolls, and sensors	273
Models T652 and T654 paper path rolls and sensors	274
Functions of main components	274
Media tray assembly	275
Multi-purpose feeder (MPF)	277
Supported paper sizes, types, and weights	278
Registration	279
Transfer	280
Polygon printhead assembly	281
Oscillating printhead assembly	283
Fuser	284
Fuser components	284
Fuser unit assembly (type 1 and type 2)	285
Exit	286
Drive	287
Electrical components and controller	288
Control	289
Printhead control	289
Fuser control	289
Xerographic and print cartridge components	290
High Capacity Input Tray (HCIT) tray assembly	296
Model T650 paper path, rolls, and sensors	301
Models T652 and T654 paper path, rolls, and sensors	302
Media tray assembly	303
Duplex	305
Model T650 duplex paper path	305
Models T652 and T654 duplex paper path	306
Understanding jam numbers and locations	308
Security Reset Jumper	320
Security Reset Jumper	320
4. Repair Information	323
Handling ESD-sensitive parts	323
Adjustments	324
Polygon and Oscillating printhead mechanical registration adjustment	324
Oscillating printhead assembly electronic adjustment	325
Alignment assembly adjustment	326
Fuser solenoid adjustment	328
Gap adjustment	328
Removals	329
Replacement note: To replace a removed part, reverse the order of removal unless noted otherwise.	329
Access door removal (T650, T652, T654)	330
Alignment assembly removal (T650, T652, T654)	330
Connection access cover, rear removal (T650, T652, T654)	333
Connection bezel assembly, rear removal (T650)	333
Connection bezel assembly, rear removal (T652, T654)	334
Cover assembly, rear lower removal (T650)	335
Cover assembly, rear lower (T652, T654)	335
Charge roll assembly removal (T650, T652, T654)	336
Door assembly, rear removal (T650, T652, T654)	337
Duplex guide assembly, rear removal (T652, T654)	337
Duplex assembly removal (T652, T654)	338
Duplex cooling fan removal (T652, T654)	340
Duplex drive motor assembly removal (T652, T654)	341
Duplex input sensor assembly removal (T652, T654)	342
Duplex guide assembly, front removal (T652, T654)	343
Fuser access door assembly removal (T650, T652, T654)	344
Fuser drive release linkage removal (T650, T652, T654)	345
Fuser unit assembly removal (T650, T652, T654)	345
Fuser wiper cover assembly removal (T650, T652, T654)	346
HVPS card assembly removal (T650, T652, T654)	346
Inner deflector removal (T650, T652, T654)	347
Laser cover removal (T650, T652, T654)	349
LCD screen bezel removal (T650, T652, T654)	350
LVPS card assembly removal (T650)	351
LVPS card assembly removal (T652, T654)	353
Main cooling fan removal (T650, T652, T654)	354
Main drive motor assembly removal (T650, T652, T654)	356
Media out actuator removal (T650, T652, T654)	357
Media support removal (T650, T652, T654)	358
Media turn guide removal (T650, T652, T654)	358
MPF cam gear removal (T650, T652, T654)	359
MPF lift plate assembly removal (T650, T652, T654)	359
MPF media out actuator removal (T650, T652, T654)	360
MPF pick roll assembly removal (T650, T652, T654)	360
MPF pick solenoid assembly removal (T650, T652, T654)	361
MPF tray door assembly removal (T650, T652, T654)	363
Operator panel latch assembly removal (T650, T652, T654)	365
Operator panel door assembly removal (T650, T652, T654)	366
Operator panel hinge assembly, left removal (T650, T652, T654)	367
Operator panel hinge assembly, right removal (T650, T652, T654)	369
Operator panel door assembly removal (models X651, X652, X654, and X656)	371
Operator panel cover latch assembly removal (models X651, X652, X654, and X656)	374
Option drive shaft removal (T650, T652, T654)	374
Output cover assembly removal (T650, T652, T654)	376
Pick arm assembly removal (T650, T652, T654)	376
Pick roll assembly removal (T650, T652, T654)	379
Print cartridge cooling fan removal (T650, T652, T654)	379
Print cartridge clamp assembly removal (T650, T652, T654)	380
Print cartridge ID connector assembly removal (T650, T652, T654)	381
Printhead assembly removal (T650)	382
Printhead assembly removal (T652, T654)	383
Redrive assembly removal (T650, T652, T654)	384
Redrive motor assembly removal (T652, T654)	385
Side cover, left removal (T650)	387
Side cover, left removal (T652 and T654)	388
Side cover, right removal (T650)	389
Side cover, right removal (T652, T654)	390
Sensor (duplex input) removal (T652, T654)	390
Sensor (media level) removal (T650, T652, T654)	392
Sensor (media out) removal (T650, T652, T654)	392
Sensor (toner empty) removal (T650, T652, T654)	393
Sensor (input) removal (T650, T652, T654)	393
Sensor shield assembly removal (T650, T652, T654)	394
Sensor (standard bin exit) removal (T650, T652, T654)	395
Sensor (toner density) removal (T650, T652, T654)	395
Standard bin actuator assembly removal (T650, T652, T654)	395
Switch (media size) assembly removal (T650, T652, T654)	396
System card assembly removal (T650, T652, T654, T656)	398
Transfer roll assembly removal (T650, T652, T654)	400
Transfer roll bracket assembly, left removal (T650, T652, T654)	401
Transfer roll bracket assembly, right removal (T650, T652, T654)	402
Transfer deflector removal (T650, T652, T654)	402
Tray roller catch assembly removal (T650, T652, T654)	403
Option removals	405
	550
	550
	550
	550
	550
	550
	550
Assembly 13: SFP stapler assembly #1	550
Assembly 14: SFP stapler assembly #2	552
Assembly 15: SFP stapler assembly #3	554
Assembly 16: SFP stapler assembly #4	556
Assembly 17: 5-bin mailbox #1	558
Assembly 18: 5-bin mailbox #2io	560
Assembly 19: High capacity stacker	562
Assembly 20: Output expander	564
Assembly 21: Envelope feeder and external duplex	566
Assembly 22: RFID UHF Option assembly	568
Assembly 23: Miscellaneous	569
Assembly 24: Power cords	571
Assembly 25: Universal trays and accessories	572
Index	573
Part number index	577
Print defects guide	585

Match case Limit results 1 per page

Diagnostic information

2-19

4062

201.01

Main drive motor

assembly load error.

Type 1 fuser

The main drive motor assembly

has failed or caused high

mechanical load due to paper

jam or bind.

1. Check all connections on

the main drive motor

assembly.

2. Check all connections on

the system card assembly.

3. Replace the main drive

motor assembly if problem

remains. Go to

“Output

cover assembly removal

(T650, T652, T654)” on

page 4-54

201.02

Sensor (fuser output)

late jam.

Type 1 fuser

The media is late reaching the

sensor (fuser output) within the

specified time.

Go to sensor (fuser output) late

jam service check.

See

“Sensor (fuser output)

late jam service check.” on

page 2-135

If problem remains, a type 2

fuser can be installed.

201.03

Image data did not

start in time

Type 1 fuser

Printhead write failure

1. Check all connections on the

printhead assembly

2. Check all connections on the

system card assembly.

3. Replace the printhead

assembly if problem remains.

4. Replace the system card

assembly if problem remains.

Go to

“System card

assembly removal (T650,

T652, T654, T656)” on

page 4-76

201.04

Sensor (narrow

media) late jam

Type 1 fuser

The expected wide media is

late reaching the sensor

(narrow media) within the

specified time.

Go to sensor (narrow media)

late jam service check.

See

“Sensor (narrow media)

late jam service check.” on

page 2-139

201.06

Sensor (narrow

media) late jam

Type 1 fuser

The expected wide media is

late reaching the sensor

(narrow media) within the

specified time.

Go to sensor (narrow media)

late jam service check.

See

“Sensor (narrow media)

late jam service check.” on

page 2-139

201.07

Sensor (fuser output)

late jam

Type 1 fuser

The media is late reaching the

sensor (fuser output) within the

specified time.

Go to sensor (fuser output) late

jam service check.

See

“Sensor (fuser output)

late jam service check.” on

page 2-135

201.25

Sensor (fuser output)

area jam.

Type 2 fuser

The media is jammed in the

sensor (fuser output) area.

Go to sensor (fuser output)

service check.

See

“Sensor (fuser output)

late jam service check.” on

page 2-135

Error

code or

message

Error contents

Description/Action

Possible repair actions