IBM 2170275 Reference Guide - Page 68

IDE Secondary Channel, Master, Drive Error, Slave, IRQ Setting Error, PnP ISA Cards Disabled

Get IBM 2170275 - Aptiva E - 2170 PDF manuals and user guides View all IBM 2170275 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 68 highlights

Error code and description Here's what to do... 1782 IDE Secondary Channel Master Drive Error 1783 IDE Secondary Channel Slave Drive Error 1800 IRQ Setting Error PnP ISA Card(s) Disabled 1 Make sure the IDE signal cable is properly connected to the drive and to the system board. 2 Make sure the drive power cable is properly connected. 3 Enter Setup and make sure that the IDE Secondary Channel Master parameter is set to Auto. For information on the Setup Utility options, see the Aptiva online help. 4 If the error still shows after performing the above steps, replace the IDE drive. It may be defective. For more information on using the Setup Utility, see "Using the Setup Utility" on page 71. 1 Make sure the IDE signal cable is properly connected to the drive and to the system board. 2 Make sure the drive power cable is properly connected. 3 Enter Setup and make sure that the IDE Secondary Channel Slave parameter is set to Auto. For information on the Setup Utility options, see the Aptiva online help. 4 If the error still shows after performing the above steps, replace the IDE drive. It may be defective. For more information on using the Setup Utility, see "Using the Setup Utility" on page 71. 1 Enter Setup and set the Reset Resource Assignments to Yes, then reboot the system. 2 If the error message reappears, determine which onboard device is least necessary and disable it under the Input/Output Ports menu in Setup. For information on the Setup Utility options, see the Aptiva online help. If any of these problems continue after taking the actions listed, run the diagnostics programs that came with your computer. If you need service, see "HelpWare support and services" on page 79. 64 Responding to error codes

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
64
Responding to error codes
1782
IDE Secondary Channel
Master
Drive Error
1
Make sure the IDE signal cable is properly connected
to the drive and to the system board.
2
Make sure the drive power cable is properly
connected.
3
Enter Setup and make sure that the IDE Secondary
Channel Master parameter is set to
Auto
. For
information on the Setup Utility options, see the
Aptiva online help.
4
If the error still shows after performing the above
steps, replace the IDE drive. It may be defective. For
more information on using the Setup Utility, see
“Using the Setup Utility” on page 71.
1783
IDE Secondary Channel
Slave
Drive Error
1
Make sure the IDE signal cable is properly connected
to the drive and to the system board.
2
Make sure the drive power cable is properly
connected.
3
Enter Setup and make sure that the IDE Secondary
Channel Slave parameter is set to
Auto
. For
information on the Setup Utility options, see the
Aptiva online help.
4
If the error still shows after performing the above
steps, replace the IDE drive. It may be defective. For
more information on using the Setup Utility, see
“Using the Setup Utility” on page 71.
1800
IRQ Setting Error
PnP ISA Card(s) Disabled
1
Enter Setup and set the Reset Resource Assignments
to
Yes
, then reboot the system.
2
If the error message reappears, determine which
onboard device is least necessary and disable it under
the Input/Output Ports menu in Setup.
For information on the Setup Utility options, see the
Aptiva online help.
Error code and description
Here’s what to do...
If any of these problems continue after taking the actions
listed, run the diagnostics programs that came with your
computer. If you need service, see “HelpWare support and
services” on page 79.