Home » Cisco Manuals » Bridges & Routers » Cisco RV042 » Manual Viewer

Cisco RV042 User Guide - Page 49

Remote Client Setup, Local Security Group Type, Remote Client - vpn setup gateway to gateway

UPC - 745883560530

Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

Chapter 4 Advanced Configuration IP + E-mail Addr.(USER FQDN) Authentication Local Security Gateway Type > IP + E-mail Addr.(USER FQDN) Authentication E-mail address Enter the e-mail address for authentication. IP address The WAN (or Internet) IP address of the Router automatically appears. Dynamic IP + Domain Name(FQDN) Authentication The Local Security Gateway will be a dynamic IP address, so you do not need to enter the IP address. When the Remote Security Gateway requests to create a tunnel with the Router, the Router will work as a responder. The domain name must match the Remote Security Gateway of the remote VPN device and can only be used for one tunnel connection. NOTE: The Local Security Group Type you select should match the Remote Security Group Type selected on the VPN device at the other end of the tunnel. After you have selected the Local Security Group Type, the settings available on this screen may change, depending on which selection you have made. IP Only the computer with a specific IP address will be able to access the tunnel. Local Security Group Type > IP IP address Enter the appropriate IP address. The default IP is 192.168.1.0. Subnet The default is Subnet. All computers on the local subnet will be able to access the tunnel. Local Security Gateway Type > Dynamic IP + Domain Name(FQDN) Authentication DomainName Enterthedomainnameforauthentication. (Once used, you cannot use it again to create a new tunnel connection.) Dynamic IP + E-mail Addr.(USER FQDN) Authentication The Local Security Gateway will be a dynamic IP address, so you do not need to enter the IP address. When the Remote Security Gateway requests to create a tunnel with the Router, the Router will work as a responder. Local Security Gateway Type > Dynamic IP + E-mail Addr.(USER FQDN) Authentication E-mail address Enter the e-mail address for authentication. Local Security Group Type Select the local LAN user(s) behind the Router that can use this VPN tunnel. Select the type you want to use: IP, Subnet, or IP Range. Follow the instructions for the type you want to use. 10/100 4-Port VPN Router Local Security Group Type > Subnet IP address Enter the IP address. The default is 192.168.1.0. Subnet Mask Enter the subnet mask. The default is 255.255.255.0. IP Range Specify a range of IP addresses within a subnet that will be able to access the tunnel. Local Security Group Type > IP Range IP range Enter the range of IP addresses. The default is 192.168.1.0~254. Remote Client Setup Remote Client Select the type you want to use: IP Only, IP + Domain Name(FQDN) Authentication, IP + E-mail Addr.(USER FQDN) Authentication, Dynamic IP + Domain Name(FQDN) Authentication, or Dynamic IP + Email Addr.(USER FQDN) Authentication. Follow the instructions for the type you want to use. 42

Section	Page
Chapter 1: Introduction	8
Introduction to the Router	8
Introduction to VPNs	8
VPN Examples	8
VPN Router to VPN Router	8
Computer (using VPN client software) to VPN Router	9
Chapter 2: Product Overview	10
Front Panel	10
Back Panel	10
Right Side Panel	10
Left Side Panel	10
Chapter 3: Installation	11
Physical Installation	11
Horizontal Placement	11
Wall-Mounting Placement	11
Cable Connections	11
Chapter 4: Advanced Configuration	13
Overview	13
How to Access the Web-Based Utility	13
System Summary	13
System Information	14
Configuration	14
Port Statistics	14
Network Setting Status	15
Firewall Setting Status	15
VPN Setting Status	15
Log Setting Status	15
Setup Tab > Network	16
Network	16
Setup > Password	19
Password	20
Setup > Time	20
Time	20
Setup > DMZ Host	20
DMZ Host	20
Setup Tab > Forwarding	21
Forwarding	21
Setup > UPnP	22
UPnP	22
Setup > One-to-One NAT	23
One-to-One NAT	23
Setup > MAC Clone	23
MAC Clone	24
Setup > DDNS	24
DDNS	24
Setup > Advanced Routing	25
Advanced Routing	25
DHCP > Setup	26
Setup	27
DHCP > Status	28
Status	28
System Management Tab > Dual-WAN	28
Dual-WAN	28
System Management > Bandwidth Management	30
Bandwidth Management	31
System Management > SNMP	32
System Management > Diagnostic	33
Diagnostic	33
System Management > Factory Default	34
Factory Default	34
System Management > Firmware Upgrade	34
Firmware Upgrade	34
Restart	35
System Management > Setting Backup	35
Import Configuration File	35
Export Configuration File	35
Port Management > Port Setup	35
Basic Per Port Config.	35
Port Management > Port Status	36
Port Status	36
Firewall > General	36
General	36
Firewall > Access Rules	37
Access Rules	38
Add a New Access Rule	38
Firewall > Content Filter	39
Content Filter	40
ProtectLink	40
VPN > Summary	40
Summary	40
VPN > Gateway to Gateway	42
Add a New Tunnel	42
IPSec Setup	45
VPN > Client to Gateway	47
Add a New Tunnel	48
IPSec Setup	51
VPN > VPN Client Access	53
VPN Client Access	54
VPN > VPN Pass Through	54
VPN Pass Through	55
VPN > PPTP Server	55
PPTP Server	55
Connection List	55
Log > System Log	55
System Log	56
Log > System Statistics	57
Wizard	58
Basic Setup	58
Access Rule Setup	61
Support	63
Manual	63
Linksys Web Site	63
Logout	63
Appendix A: Troubleshooting	64
Appendix B: Linksys QuickVPN for Windows 2000, XP, or Vista	65
Introduction	65
Computer (using VPN client software) to VPN Router	65
Linksys QuickVPN Instructions	65
Router Configuration	65
Export a Client Certificate from the Router	65
Add VPN Client Users	66
Linksys QuickVPN Client Installation and Configuration	66
Install from the CD-ROM	66
Download from the Internet	67
Install the Client Certificate	67
Use of the Linksys QuickVPN Software	67
Linksys QuickVPN Connection	67
Version Number of Linksys QuickVPN	68
Appendix C: Gateway-to-Gateway VPN Tunnel	69
Overview	69
Before You Begin	69
Configuration when the Remote Gateway Uses a Static IP Address	69
Configuration of the RVL200	69
Configuration of the RV042	70
Configuration of PC 1 and PC 2	70
Configuration when the Remote Gateway Uses a Dynamic IP Address	71
Configuration of the RVL200	71
Configuration of the RV042	71
Configuration of PC 1 and PC 2	72
Configuration when Both Gateways Use Dynamic IP Addresses	72
Configuration of the RVL200	72
Configuration of the RV042	73
Configuration of PC 1 and PC 2	73
Appendix D: IPSec NAT Traversal	74
Overview	74
Before You Begin	74
Configuration of Scenario 1	74
Configuration of Router A	74
Configuration of Router B	75
Configuration of Scenario 2	76
Configuration of the One-to-One NAT Rules	76
Configuration of Router B	77
Configuration of Router A	77
Appendix E: Bandwidth Management	79
Overview	79
Creation of New Services	79
Creation of New Bandwidth Management Rules	80
Appendix F: Firmware Upgrade	81
Overview	81
How to Access the Web-Based Utility	81
Upgrade the Firmware	81
Alternative Firmware Upgrade Option	81
Appendix G: Trend Micro ProtectLink Gateway Service	83
Overview	83
How to Access the Web-Based Utility	83
How to Purchase, Register, or Activate the Service	83
System Summary	83
ProtectLink	84
How to Use the Service	84
ProtectLink > Web Protection	85
ProtectLink > Email Protection	86
ProtectLink > License	86
Appendix H: Specifications	88
Appendix I: Warranty Information	89
Exclusions and Limitations	89
Obtaining Warranty Service	89
Technical Support	90
Appendix J: Software License Agreement	91
Software in Linksys Products:	91
Software Licenses:	91
Schedule 1	91
Linksys Software License Agreement	91
END OF SCHEDULE 1	92
Schedule 2	92
GNU GENERAL PUBLIC LICENSE	92
END OF SCHEDULE 2	95
Schedule 3	95
OpenSSL License	96
Original SSLeay License	96
END OF SCHEDULE 3	97
Appendix K: Regulatory Information	98
FCC Statement	98
Safety Notices	98
Industry Canada Statement	98
Avis d’Industrie Canada	98
User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic Equipment (WEEE)	99

Match case Limit results 1 per page

Chapter 4

Advanced Configuration

10/100 4-Port VPN Router

IP + E-mail Addr.(USER FQDN) Authentication

Local Security Gateway Type > IP + E-mail Addr.(USER FQDN)

Authentication

E-mail

address

Enter

the

e-mail

address

for

authentication.

IP address

The WAN (or Internet) IP address of the Router

automatically appears.

Dynamic IP + Domain Name(FQDN) Authentication

The Local Security Gateway will be a dynamic IP address,

so you do not need to enter the IP address. When the

Remote Security Gateway requests to create a tunnel with

the Router, the Router will work as a responder.

The domain name must match the Remote Security

Gateway of the remote VPN device and can only be used

for one tunnel connection.

Local Security Gateway Type > Dynamic IP + Domain Name(FQDN)

Authentication

Domain Name

Enter the domain name for authentication.

(Once used, you cannot use it again to create a new tunnel

connection.)

Dynamic IP + E-mail Addr.(USER FQDN) Authentication

The Local Security Gateway will be a dynamic IP address,

so you do not need to enter the IP address. When the

Remote Security Gateway requests to create a tunnel with

the Router, the Router will work as a responder.

Local Security Gateway Type > Dynamic IP + E-mail Addr.(USER FQDN)

Authentication

E-mail

address

Enter

the

e-mail

address

for

authentication.

Local Security Group Type

Select the local LAN user(s) behind the Router that can

use this VPN tunnel. Select the type you want to use:

Subnet

, or

IP Range

. Follow the instructions for the type

you want to use.

NOTE:

The Local Security Group Type you select

should match the Remote Security Group Type

selected on the VPN device at the other end of

the tunnel.

After you have selected the Local Security Group Type, the

settings available on this screen may change, depending

on which selection you have made.

Only the computer with a specific IP address will be able

to access the tunnel.

Local Security Group Type > IP

IP address

Enter the appropriate IP address. The default

IP is

192.168.1.0

Subnet

The default is

Subnet

. All computers on the local subnet

will be able to access the tunnel.

Local Security Group Type > Subnet

address

Enter

the

address.

The

default

192.168.1.0

Subnet Mask

Enter the subnet mask. The default is

255.255.255.0

IP Range

Specify a range of IP addresses within a subnet that will be

able to access the tunnel.

Local Security Group Type > IP Range

IP range

Enter the range of IP addresses. The default is

192.168.1.0~254

Remote Client Setup

Remote Client

Select the type you want to use:

IP Only

IP + Domain

Name(FQDN) Authentication

IP + E-mail Addr.(USER

FQDN)

Authentication

Dynamic

Domain

Name(FQDN) Authentication

, or

Dynamic IP + E-

mail Addr.(USER FQDN) Authentication

. Follow the

instructions for the type you want to use.