HP 6125G HP 6125G & 6125G/XG Blade Switches Network Management and Mon - Page 160

reaction trap

Get HP 6125G PDF manuals and user guides View all HP 6125G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 160 highlights

[Sysname-nqa-admin-test-udp-jitter] reaction 1 checked-element rtt threshold-type average threshold-value 50 5 action-type trap-only # Create reaction entry 2 for monitoring the round-trip time of UDP jitter probe packets. Set the upper threshold to 50 milliseconds, and lower threshold to 5 milliseconds. Before the NQA test group starts, the initial state of the reaction entry is invalid. After each test, the packet round-trip time is checked against the threshold range. If the total number of threshold violations exceeds 100 (included), the state of the entry is set to over-threshold. Otherwise, the state of the entry is set to below-threshold. Once the state of the reaction entry changes, a trap message is generated and sent to the network management server. system-view [Sysname] nqa entry admin test [Sysname-nqa-admin-test] type udp-jitter [Sysname-nqa-admin-test-udp-jitter] reaction 1 checked-element rtt threshold-type accumulate 100 threshold-value 50 5 action-type trap-only reaction trap Syntax reaction trap { probe-failure consecutive-probe-failures | test-complete | test-failure cumulate-probe-failures } undo reaction trap { probe-failure | test-complete | test-failure } View Any NQA operation view Default level 2: System level Parameters probe-failure consecutive-probe-failures: Sends a trap to the network management server if the number of consecutive probe failures in one test is greater than or equal to consecutive-probe-failures. The value for consecutive-probe-failures is in the range of 1 to 15. During the test, the system counts the number of consecutive probe failures after each probe operation, so multiple traps might be sent. test-complete: Sends a trap to indicate that the test is completed. test-failure cumulate-probe-failures: Sends a trap if the total probe failures in an test is greater than or equal to cumulate-probe-failures. The value for cumulate-probe-failures is in the range of 1 to 15. The system counts the total probe failures after the test completes, so one trap at most is sent. Description Use reaction trap to configure the sending of traps to the network management server under specified conditions. Use undo reaction trap to restore the default. By default, no traps are sent to the network management server. Only the reaction trap test-complete command is supported by voice tests. Examples # Configure the system to send a trap if consecutive probe failures in an ICMP echo test is greater than or equal to 5. system-view 154

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
154
[Sysname-nqa-admin-test-udp-jitter] reaction 1 checked-element rtt threshold-type
average threshold-value 50 5 action-type trap-only
# Create reaction entry 2 for monitoring the round-trip time of UDP jitter probe packets. Set the upper
threshold to 50 milliseconds, and lower threshold to 5 milliseconds. Before the NQA test group starts, the
initial state of the reaction entry is invalid. After each test, the packet round-trip time is checked against
the threshold range. If the total number of threshold violations exceeds 100 (included), the state of the
entry is set to over-threshold. Otherwise, the state of the entry is set to below-threshold. Once the state of
the reaction entry changes, a trap message is generated and sent to the network management server.
<Sysname> system-view
[Sysname] nqa entry admin test
[Sysname-nqa-admin-test] type udp-jitter
[Sysname-nqa-admin-test-udp-jitter] reaction 1 checked-element rtt threshold-type
accumulate 100 threshold-value 50 5 action-type trap-only
reaction trap
Syntax
reaction
trap
{
probe-failure
consecutive-probe-failures
|
test-complete
|
test-failure
cumulate-probe-failures
}
undo reaction trap
{
probe-failure
|
test-complete
|
test-failure
}
View
Any NQA operation view
Default level
2: System level
Parameters
probe-failure
consecutive-probe-failures
: Sends a trap to the network management server if the number
of consecutive probe failures in one test is greater than or equal to
consecutive-probe-failures
. The value
for
consecutive-probe-failures
is in the range of 1 to 15. During the test, the system counts the number of
consecutive probe failures after each probe operation, so multiple traps might be sent.
test-complete
: Sends a trap to indicate that the test is completed.
test-failure
cumulate-probe-failures
: Sends a trap if the total probe failures in an test is greater than or
equal to
cumulate-probe-failures
. The value for
cumulate-probe-failures
is in the range of 1 to 15. The
system counts the total probe failures after the test completes, so one trap at most is sent.
Description
Use
reaction trap
to configure the sending of traps to the network management server under specified
conditions.
Use
undo reaction trap
to restore the default.
By default, no traps are sent to the network management server.
Only the
reaction trap test-complete
command is supported by voice tests.
Examples
# Configure the system to send a trap if consecutive probe failures in an ICMP echo test is greater than
or equal to 5.
<Sysname> system-view