Yamaha 02R96 Owner's Manual - Page 273
Appendix B: Specifications, General Spec
View all Yamaha 02R96 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 273 highlights
260 Appendix B: Specifications Appendix B: Specifications General Spec Number of scene memories Sampling Frequency Signal Delay Fader Fader Resolution Total Harmonic Distortion1 (CH INPUT to STEREO OUT) (Input Gain=Min.) Frequency Response (CH INPUT to STEREO OUT) Dynamic Range (maximum level to noise level) Hum & Noise2 (20 Hz-20 kHz) Rs=150 Ω Input Gain=Max. Input Pad =0 dB Maximum Voltage Gain Crosstalk (@ 1 kHz) Input Gain=Min. AD Input (1-16: A/B) AD Input (17-24) Analog Input (2TR IN ANALOG 1, 2) Internal External fs=48 kHz fs=96 kHz 99 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz Normal rate: 44.1 kHz-10% to 48 kHz+6% Double rate: 88.2 kHz-10% to 96 kHz+6% Less than 2.0 ms CH INPUT to STEREO OUT (fs=48 kHz) Less than 1.1 ms CH INPUT to STEREO OUT (fs=96 kHz) 100 mm motorized with touch sense × 25 +10 to -96, -∞ dB (256 steps/100 mm) input faders 0 to -130, -∞ dB (256 steps/100 mm) master faders, stereo fader Less than 0.05% 20 Hz to 20 kHz @ +14 dB into 600 Ω Less than 0.01% 1 kHz @ +18 dB into 600 Ω Less than 0.05% 20 Hz to 40 kHz @ +14 dB into 600 Ω Less than 0.01% 1 kHz @ +18 dB into 600 Ω 20 Hz-20 kHz, 0.5, -1.5 dB @ +4 dB into 600 Ω (fs=48 kHz) 20 Hz-40 kHz, 0.5, -1.5 dB @ +4 dB into 600 Ω (fs=96 kHz) 110 dB typ. DA Converter (STEREO OUT) 105 dB typ. AD+DA (to STEREO OUT) @ fs=48 kHz 105 dB typ. AD+DA (to STEREO OUT) @ fs=96 kHz -128 dB Equivalent Input Noise -92 dB residual output noise. STEREO OUT (STEREO OUT off) -92 dB (96 dB S/N) STEREO OUT (STEREO fader at nominal level and all CH INPUT faders at minimum level) -64 dB (68 dB S/N) STEREO OUTPUT (STEREO fader at nominal level and one CH INPUT fader at nominal level) 74 dB CH INPUT (CH1-24) to STEREO OUT/OMNI (BUS) OUT 74 dB CH INPUT (CH1-24) to OMNI (AUX) OUT (via pre input fader) 74 dB CH INPUT (CH1-24) to CONTROL ROOM MONITOR OUT (via STEREO bus) -80 dB adjacent input channels (CH1-24) -80 dB input to output Phantom switch Pad switch Gain control Peak indicator Signal indicator Insert Insert switch AD converter Gain control Peak indicator Signal indicator AD converter +48 V DC is supplied to A (XLR-3-31 type) input 0/26 dB attenuation 44 dB (-60 to -16), detented LED (red) turns on when post HA level reaches 3 dB below clipping LED (green) turns on when post HA level reaches 20 dB below nominal I/O (pre AD converter) on/off 24-bit linear, 128-times oversampling (fs=48 kHz) 44 dB (-34 to +10), detented LED (red) turns on when post HA level reaches 3 dB below clipping LED (green) turns on when post HA level reaches 20 dB below nominal 24-bit linear, 128-times oversampling (fs=48 kHz) AD converter 24-bit linear, 128-times oversampling (fs=48 kHz) 02R96-Owner's Manual