Yamaha 02R96 Owner's Manual - Page 281

268 Appendix B: Specifications Analog Input Spec Input PAD GAIN Actual Load Impedance For Use With Nominal Input level Sensitivity1 Nominal Max. before clip Connector -60 dB 0 INPUT A/B 1-16 -16 dB 26 INPUT 17-24 INSERT IN 1-16 -34 dB - +10 dB - 2TR IN ANALOG 1 [L, R] - 2TR IN ANALOG 2 [L, R] - 3k Ω 4K Ω 10K Ω 10K Ω 10K Ω 50-600 Ω Mics & 600 Ω Lines 600 Ω Lines 600 Ω Lines -70 dB (0.245 mV) -26 dB (38.8 mV) 0 dB (775 mV) -44 dB (4.89 mV) 0 dB (775 mV) -6 dB (388 mV) -60 dB (0.775 mV) -16 dB (0.123 V) +10 dB (2.45 V) -34 dB (15.5 mV) +10 dB (2.45 V) +4 dB (1.23 V) 600 Ω Lines +4 dB (1.23 V) +4 dB (1.23 V) 600 Ω Lines -10 dBV (0.316 V) -10 dBV (0.316 V) -46 dB A: XLR-3-31 type (Bal(3.88 mV) anced)2 -2 dB B: Phone jack (TRS) (616 mV) (Balanced)3 +24 dB (12.28 V) -20 dB (77.5 mV) +24 dB (12.28 V) Phone jack (TRS) (Balanced)3 +18 dB (6.16 V) Phone jack (TRS)4 +18 dB Phone jack (TRS) (Bal(6.16 V) anced)3 +4 dBV (1.58 V) Phono (Unbalanced) 1. Sensitivity is the lowest level that will produce an output of +4 dB (1.23 V) or the nominal output level when the unit is set to maximum gain. (All faders and level controls are maximum position.) 2. XLR-3-31 type connectors are balanced (1=GND, 2=HOT, 3=COLD). 3. Phone jacks are balanced (Tip=HOT, Ring=COLD, Sleeve=GND). 4. Phone jacks are wired: Tip=OUT, Ring=IN, Sleeve=GND In these specifications, when dB represents a specific voltage, 0 dB is referenced to 0.775 Vrms. For 2TR IN ANALOG 2 levels, 0 dBV is referenced to 1.00 Vrms. All input AD converters (except INSERT I/O 1-16) are 24-bit linear, 128-times oversampling. +48 V DC (phantom power) is supplied to CH INPUT (1-16) XLR type connectors via individual switches. Analog Output Spec Output STEREO OUT [L, R] STUDIO MONITOR OUT [L, R] C-R MONITOR OUT [L, R] OMNI OUT 1-8 INSERT OUT 1-16 PHONES Actual Source Impedance For Use With Nominal GAIN SW1 600 Ω 10k Ω Lines - 150 Ω 600 Ω Lines - 150 Ω 10k Ω Lines - 150 Ω 150 Ω 600 Ω 100 Ω 10k Ω Lines - 10k Ω Lines +18 dB (default) +4 dB 10k Ω Lines - 8 Ω Phones - 40 Ω Phones - Output level Nominal Max. before clip Connector -10 dBV (0.316 V) +4 dB (1.23 V) +4 dB (1.23 V) +4 dB (1.23 V) +4 dB (1.23 V) -10 dB (0.245 V) +4 dB (1.23 V) 4 mW 12 mW +4 dBV (1.58 V) +18 dB (6.16 V) +18 dB (6.16 V) +18 dB (6.16 V) +18 dB (6.16 V) +4 dB (1.23 V) +18 dB (6.16 V) 25 mW 75 mW Phono (Unbalanced) XLR-3-32 type (Balanced)2 Phone Jack (TRS) (Balanced)3 Phone Jack (TRS) (Balanced)3 Phone Jack (TRS) (Balanced)3 Phone Jack (TRS)4 Stereo Phone Jack (TRS) (Unbalanced)5 1. The maximum output level of each OMNI OUT can be set internally. 2. XLR-3-32 type connectors are balanced (1=GND, 2=HOT, 3=COLD). 3. Phone jacks are balanced (Tip=HOT, Ring=COLD, Sleeve=GND). 4. Phone jacks are wired: Tip=OUT, Ring=IN, Sleeve=GND 5. PHONES stereo phone jack is unbalanced (Tip=LEFT, Ring=RIGHT, Sleeve=GND). STEREO OUT [L, R], 0 dBV is referenced to 1.00 Vrms. In these specifications, when dB represents a specific voltage, 0 dB is referenced to 0.775 Vrms. All output DA converters (except INSERT OUT 1-16) are 24-bit, 128-times oversampling. 02R96-Owner's Manual