Yamaha 02R96 Owner's Manual - Page 300

Format Details 287 change. STATUS 11110000 F0 System exclusive message ID No. 01000011 43 Manufacture's ID number (YAMAHA) SUB STATUS 0001nnnn 1n n=0-15 (Device number=MIDI Channel) GROUP ID 00111110 3E MODEL ID (digital mixer) MODEL ID 00001011 0B 02R96 ADDRESS 00100001 21 Address UU 0aaaaaaa aa Address UL 0aaaaaaa aa Address LU 0aaaaaaa aa Address LL DATA 0ddddddd dd Data1 H 0ddddddd dd Data1 L : EOX 11110111 F7 End of exclusive Meter data uses the unmodified DECAY value of the DSP. For the interpretation of the value, refer to the PARAMETER CHANGE PARAMETER NUMBER LIST. 12.3.22 Parameter request (Remote Meter) Reception This is received if [Parameter change RX] is ON and the [Rx CH] matches the device number included in the SUB STATUS. This is echoed if [Parameter change ECHO] is ON. When this is received, the parameter specified by Address (refer to PARAMETER CHANGE PARAMETER NUMBER LIST) will be transmitted on the [Rx CH] at 50 msec intervals for a duration of 10 seconds. If Address UL= 0x7F is received, transmission of all meter data will be halted immediately. (disable) Transmission If [Parameter Change ECHO] is ON, this message is retransmitted without change. STATUS ID No. SUB STATUS GROUP ID MODEL ID ADDRESS DATA EOX 11110000 F0 01000011 43 0011nnnn 3n 00111110 3E 00001011 0B 00100001 21 0aaaaaaa aa 0aaaaaaa aa 0aaaaaaa aa 0cccccccc cc 0cccccccc Cc 11110111 F7 System exclusive message Manufacture's ID number (YAMAHA) n=0-15 (Device number=MIDI Channel) MODEL ID (digital mixer) 02R96 Address UU Address UL Address LU Address LL Count H Count L End of exclusive 12.3.23 Parameter change (Remote Time Counter) When transmission is enabled by receiving a Request of Remote Time Counter, the Time Counter data is transmitted every 50 msec for 10 seconds. When you want to transmit Counter information continuously, a Request must be transmitted within every 10 seconds. Reception This is echoed if [Parameter change ECHO] is ON. Transmission When transmission is enabled by receiving a Request, the Time Counter information is transmitted on [RxCH] channel every 50 msec for 10 seconds. Transmission will be disabled if the power is turned off and on again, or if the PORT setting is changed. If [Parameter Change ECHO] is ON, this message is retransmitted without change. STATUS ID No. SUB STATUS GROUP ID MODEL ID ADDRESS DATA 11110000 F0 01000011 43 0001nnnn 1n 00111110 3E 00001011 0B 00100001 22 0000tttt 0t 0ddddddd dd 0ddddddd dd 0ddddddd dd 0ddddddd dd System exclusive message Manufacture's ID number (YAMAHA) n=0-15 (Device number=MIDI Channel) MODEL ID (digital mixer) 02R96 Remote Time Counter 0:Time Code, 1: Measure, Beat, Clock Hour / Measure H Min / Measure L Sec / Beat Frame / Clock EOX 11110111 F7 End of exclusive 12.3.24 Parameter request (Remote Time Counter) Reception This is received if [Parameter change RX] is ON and the [Rx CH] matches the device number included in the SUB STATUS. This is echoed if [Parameter change ECHO] is ON. When this is received, the Time Counter information is transmitted on the [Rx CH] channel every 50 msec for 10 seconds. When the second byte of Address is received on 0x7F, data transmission will be halted immediately. Transmission If [Parameter Change ECHO] is ON, this message is retransmitted without change. STATUS ID No. 11110000 F0 System exclusive message 01000011 43 Manufacture's ID number (YAMAHA) SUB STATUS 0011nnnn 3n n=0-15 (Device number=MIDI Channel) GROUP ID MODEL ID 00111110 3E MODEL ID (digital mixer) 00001011 0B 02R96 ADDRESS 00100001 22 Remote Time Counter EOX 0aaaaaaa aa 0:Transmission request, 0x7F:Transmission stop request 11110111 F7 End of exclusive 12.3.25 Parameter change (Automix Status) When transmission is enabled by receiving a Request of Automix status, the Automix Status data is transmitted every second for 10 seconds. When you want to transmit the Automix Status information continuously, the Request must be transmitted continuously minimum within 10 seconds interval. The data is transmitted continuously while the transmission is enabled, even when the Automix Status on the 02R96 has been changed. Reception This is echoed if [Parameter change ECHO] is ON. Transmission When the transmission is set to enable by receiving a Request. The Automix Status data is transmitted on the [Rx CH] channel every second for 10 seconds. The data is transmitted continuously while the transmission is enabled, even when the Automix Status on the 02R96 has been changed. Transmission will be disabled if the power is turned off and on again, or if the PORT setting is changed. If [Parameter Change ECHO] is ON, this message is retransmitted without change. STATUS 11110000 F0 System exclusive message ID No. 01000011 43 Manufacture's ID number (YAMAHA) SUB STATUS 0001nnnn 1n n=0-15 (Device number=MIDI Channel) GROUP ID 00111110 3E MODEL ID (digital mixer) MODEL ID 00001011 0B 02R96 ADDRESS 00100011 23 Automix Status DATA EOX 00000000 00 0000dddd 0d Automix Status H 0000dddd 0d Automix Status L 11110111 F7 End of exclusive 12.3.26 Parameter request (Automix Status) Reception This is received if [Parameter change RX] is ON and the [Rx CH] matches the device number included in the SUB STATUS. This is echoed if [Parameter change ECHO] is ON. When the data is received, the Automix Status data is transmitted on the [Rx CH] every second for 10 seconds. When the second byte of Address is received on 0x7F, data transmission will be halted immediately (disable). Transmission If [Parameter Change ECHO] is ON, this message is retransmitted without change. STATUS 11110000 F0 System exclusive message ID No. 01000011 43 Manufacture's ID number (YAMAHA) SUB STATUS 0011nnnn 3n n=0-15 (Device number=MIDI Channel) GROUP ID 00111110 3E MODEL ID (digital mixer) MODEL ID ADDRESS 00001011 0B 02R96 00100011 23 Automix Status EOX 0aaaaaaa aa 0:Transmission request, 0x7F:Transmission stop request 11110111 F7 End of exclusive 02R96-Owner's Manual