Dell PowerConnect J-8208 Hardware Guide - Page 148

Power Cord Retainer in an AC Power Supply

Get Dell PowerConnect J-8208 PDF manuals and user guides View all Dell PowerConnect J-8208 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 148 highlights

Dell PowerConnect J-Series J-EX8208 Ethernet Switch Hardware Guide 1. Attach the electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the strap to the ESD point on the chassis. 2. Ensure that the power supply is fully inserted and latched securely in the chassis. See "Installing an AC Power Supply in a J-EX8200 Switch" on page 114. 3. Flip the Enable switch, which is next to the appliance inlet on the power supply faceplate, to the Standby position. 4. Squeeze the two sides of the power cord retainer clip, and insert the L-shaped ends of the clip into the holes in the bracket on each side of the AC appliance inlet on the AC power supply faceplate. See Figure 64 on page 132. Figure 64: Power Cord Retainer in an AC Power Supply 5. Locate the jumper cord or cords shipped with the switch-or the separately orderable power cords that have plugs appropriate for your geographical location. 6. Insert the coupler end of the jumper cord or power cord into the AC appliance inlet on the AC power supply faceplate. NOTE: If the power cord tray is installed, you can thread the jumper cord or power cord through the power cord tray. See Figure 65 on page 133. 7. Push the cord (close to the coupler end) into the slot in the adjustment nut of the power cord retainer. Rotate the nut until it is tight against the base of the coupler and the slot in the nut is turned 90° from the top of the switch. See Figure 65 on page 133. 8. If the AC power source outlet has a power switch, set it to the OFF (0) position. 9. Insert the jumper cord or power cord plug into an AC power source outlet. 10. If the AC power source outlet has a power switch, set it to the ON (|) position. 11. Verify that the INPUT OK LED on the power supply faceplate is lit and is on steadily. 12. Repeat Steps 2 through 11 for the remaining power supplies. 132

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
  • 270
  • 271
  • 272
  • 273
  • 274
  • 275
  • 276
1.
Attach the electrostatic discharge (ESD) grounding strap to your bare wrist, and
connect the strap to the ESD point on the chassis.
2.
Ensure that the power supply is fully inserted and latched securely in the chassis. See
“Installing an AC Power Supply in a J-EX8200 Switch” on page 114.
3.
Flip the
Enable
switch, which is next to the appliance inlet on the power supply
faceplate, to the Standby position.
4.
Squeeze the two sides of the power cord retainer clip, and insert the L-shaped ends
of the clip into the holes in the bracket on each side of the AC appliance inlet on the
AC power supply faceplate. See Figure 64 on page 132.
Figure 64: Power Cord Retainer in an AC Power Supply
5.
Locate the jumper cord or cords shipped with the switch—or the separately orderable
power cords that have plugs appropriate for your geographical location.
6.
Insert the coupler end of the jumper cord or power cord into the AC appliance inlet on
the AC power supply faceplate.
NOTE:
If the power cord tray is installed, you can thread the jumper cord
or power cord through the power cord tray. See Figure 65 on page 133.
7.
Push the cord (close to the coupler end) into the slot in the adjustment nut of the
power cord retainer. Rotate the nut until it is tight against the base of the coupler and
the slot in the nut is turned 90° from the top of the switch. See Figure 65 on page 133.
8.
If the AC power source outlet has a power switch, set it to the OFF (0) position.
9.
Insert the jumper cord or power cord plug into an AC power source outlet.
10.
If the AC power source outlet has a power switch, set it to the ON (|) position.
11.
Verify that the
INPUT OK
LED on the power supply faceplate is lit and is on steadily.
12.
Repeat Steps 2 through 11 for the remaining power supplies.
132
Dell PowerConnect J-Series J-EX8208 Ethernet Switch Hardware Guide