HP P Class 450/500/550/600/650/700/750 HP Visualize x- and p-Class (733,800, 8 - Page 50

Connecting SE SCSI Accessories

Get HP P Class 450/500/550/600/650/700/750 PDF manuals and user guides View all HP P Class 450/500/550/600/650/700/750 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Using Your Personal Workstation Connecting SCSI Accessories Connecting SE SCSI Accessories The intended use for the internal Wide SE SCSI and Narrow SE SCSI connectors is to connect internal Wide and Narrow single-ended SCSI devices to your Personal Workstation. An internal Wide or Narrow single-ended SCSI device can be connected as follows: 1. Assign an unused SCSI address to the accessory. SCSI addresses range from 0 to 15 for wide 16-bit SCSI devices and 0 to 8 for narrow 8-bit SCSI devices. The SCSI address 0 is reserved for the first SCSI hard disk drive and SCSI address 7 is reserved for the SCSI controller (the default for narrow and wide SCSI devices). Refer to the manual provided with the SCSI accessory for instructions on selecting a SCSI address. 2. Connect the SCSI accessory to your Personal Workstation's internal 68-pin wide SE SCSI connector or 50-pin narrow SE SCSI connector with the SCSI cable you purchased. 3. Refer to the manual that was provided with you SCSI accessory to learn how to install any software that may be necessary for using it. 50 Chapter 1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
50
Chapter 1
Using Your Personal Workstation
Connecting SCSI Accessories
Connecting SE SCSI Accessories
The intended use for the internal Wide SE SCSI and Narrow SE SCSI
connectors is to connect internal Wide and Narrow single-ended SCSI
devices to your Personal Workstation.
An internal Wide or Narrow single-ended SCSI device can be connected
as follows:
1.
Assign an unused SCSI address to the accessory. SCSI addresses
range from 0 to 15 for wide 16-bit SCSI devices and 0 to 8 for narrow
8-bit SCSI devices. The SCSI address 0 is reserved for the first SCSI
hard
disk
drive
and
SCSI
address
7
is
reserved
for
the
SCSI
controller (the default for narrow and wide SCSI devices).
Refer
to
the
manual
provided
with
the
SCSI
accessory
for
instructions on selecting a SCSI address.
2.
Connect the SCSI accessory to your Personal Workstation’s internal
68-pin wide SE SCSI connector or 50-pin narrow SE SCSI connector
with the SCSI cable you purchased.
3.
Refer to the manual that was provided with you SCSI accessory to
learn how to install any software that may be necessary for using it.