Intermec PX4i PX4i and PX6i High Performance Printer User's Manual - Page 132

Adjusting the Printer, Adjusting the Pressure Arm

Get Intermec PX4i PDF manuals and user guides View all Intermec PX4i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 132 highlights

Chapter 4 - Troubleshooting and Maintaining the Printer Adjusting the Printer You may need to adjust your printer to accommodate your printing needs or improve performance. You can adjust the: • pressure arm. • label stop sensor (LSS) position. • printhead pressure. • label taken sensor. Adjusting the Pressure Arm The printer is factory-adjusted for full-size media width. If you are using media that is less than full width, Intermec recommends that you adjust the position of the pressure arm so that it is centered on the media and provides even pressure. A poorly adjusted pressure arm may be detected by a weaker printout on either side of the media path. To adjust the pressure arm 1 Turn off the printer. 2 Open the front door and media cover. 3 If necessary, remove the ribbon. 118 PX4i and PX6i High Performance Printer User's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
Chapter 4 — Troubleshooting and Maintaining the Printer
118
PX4i and PX6i High Performance Printer User’s Manual
Adjusting the Printer
You may need to adjust your printer to accommodate your printing
needs or improve performance. You can adjust the:
•
pressure arm.
•
label stop sensor (LSS) position.
•
printhead pressure.
•
label taken sensor.
Adjusting the Pressure Arm
The printer is factory-adjusted for full-size media width. If you are
using media that is less than full width, Intermec recommends that
you adjust the position of the pressure arm so that it is centered on
the media and provides even pressure.
A poorly adjusted pressure arm may be detected by a weaker printout
on either side of the media path.
To adjust the pressure arm
1
Turn off the printer.
2
Open the front door and media cover.
3
If necessary, remove the ribbon.