Home » HP Manuals » Desktops » HP t310 » Manual Viewer

HP t310 PCoIP Administrator's Guide - Page 49

Configuring the Discovery Mechanism, Discovery Configuration

Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

PCoIP Administrator's Guide 4.5 Configuring the Discovery Mechanism Use the settings on the Discovery Configuration page to ease the discovery of hosts and clients in your PCoIP system and dramatically reduce the configuration and maintenance effort for complex systems. This discovery mechanism is independent of DNS SRV discovery. Note: For SLP discovery to work across subnets, routers must be configured to forward multicast traffic between subnets. Because most deployments do not allow this, DNS-SRV Discovery is the recommended discovery mechanism. Figure 4-9: Administrative Web Interface Discovery Page TER0606004 Issue 16 49

Section	Page
Revision History	3
Table of Figures	12
Table of Tables	16
Definitions	18
1 Introduction	20
1.1 About this Document	20
1.2 Menu and Page Overview	21
2 Administrative Web Interface Overview	25
2.1 About the Page Layout	25
2.2 Supported Web Browsers	26
2.3 Administrative Web Interface IP Address	27
2.4 Administrative Interface Security	27
2.4.1 Installing the CA Root Certificate	27
2.5 Logging In	27
2.6 Viewing the Home Page	28
2.7 About the Administrative Interface Menus	32
2.7.1 Viewing the Configuration Menu	33
2.7.2 Viewing the Permissions Menu	34
2.7.3 Viewing the Diagnostics Menu	34
2.7.4 Viewing the Information Menu	34
2.7.5 Viewing the Upload Menu	34
3 Working with the On Screen Display (OSD)	35
3.1 About the Connect Window	35
3.1.1 Connect Button	36
3.2 About the OSD Options Menu	36
4 Configuring the Device	37
4.1 Initial Setup Page	37
4.2 Configuring the Network Settings	41
4.3 Configuring the IPv6 Settings for a Device	44
4.4 Adding Custom Information for the Device	47
4.5 Configuring the Discovery Mechanism	49
4.6 Configuring the SNMP Agent	51
4.7 Configuring the Session	51
4.7.1 Configuring a Direct Session	53
4.7.2 Configuring a Direct Session with SLP Host Discovery	58
4.7.3 Configuring a VMware View Connection	62
4.7.4 Configuring Kiosk Mode	70
4.7.5 Configuring a View Connection Server + Imprivata OneSign Connection	76
4.7.6 Enabling or Disabling Connection Management	80
4.8 Controlling the Bandwidth for PCoIP Sessions	85
4.9 Setting the User Interface Language	86
4.10 Configuring the OSD Screen-saver Timeout	88
4.11 Adjusting the Image Quality	89
4.12 Enabling the Host Driver Function	94
4.13 Configuring the NTP Parameters	95
4.14 Updating the Password for a Device	96
4.15 Resetting the Parameters to Factory Default Values	97
4.16 Configuring the EDID Override Mode	99
4.17 Enabling Monitor Emulation	101
4.18 Enabling or Disabling the OSD Configuration Menus	102
4.19 Enabling or Disabling the Web Server	102
5 Setting up the User Permissions	104
5.1 Specifying USB Devices	104
5.2 Configuring the Audio Parameters	106
5.3 Setting up the Client's Power-off Permissions	107
6 Using the Diagnostic Tools	109
6.1 Viewing and Clearing Event Log Messages	109
6.1.1 Syslog Features	109
6.2 Controlling the Device Session	112
6.3 Viewing PCoIP Protocol Statistics	113
6.4 Working with the Host Information and Power State	117
6.5 Generating an Audio Test Tone from the Client	118
6.6 Viewing a Test Pattern on the Client's Display	119
6.7 Resetting the Device Processor	120
6.8 Determining if a Device is Reachable	121
7 Viewing Device Information	123
7.1 Viewing the Version Information	123
7.2 Viewing the Attached Devices	125
8 Uploading to the Device	128
8.1 Uploading Firmware to the Device	128
8.1.1 Firmware Upload Process Example:	128
8.2 Uploading a Logo to the Device	129
8.2.1 OSD Logo Upload Process Example	130
8.3 Uploading the Certificate	130
8.3.1 Uploading Certificates for 802.1X Authentication	131
9 Configuring the User Settings	132
9.1 Configuring VMware View Certificate Checking	132
9.2 Configuring the Mouse Settings	133
9.3 Changing the Keyboard Repeat Settings	134
9.4 Adjusting the Image Quality from the OSD	135
9.5 Configuring the Display Topology	135
9.6 Configuring the Touch Screen	138
9.6.1 Installing the Touch Screen to the Zero Client	139
9.6.2 Setting up the Touch Screen as a Bridged Device	139
9.6.3 Configuring the Zero Client to Automatically Log into a VMware View Host	140
10 About the Overlay Windows	142
10.1 Network Connection Lost Overlay	142
10.2 Preparing Desktop Overlay	142
10.3 USB Device Not Authorized Overlay	143
10.4 USB Over Current Notice Overlay	143
10.5 USB Device Not Supported Behind a High-speed Hub Overlay	143
10.6 Resolution Not Supported Overlay	143
10.7 Half Duplex Overlay	144
10.8 Video Source Overlays	144
11 Using Smart Cards with PCoIP Zero Clients	146
11.1 Smart Card Requirements	146
11.1.1 Virtual Desktop Environment	146
11.1.2 Supported USB Card Readers	146
11.1.3 CAC Smart Card Properties	147
11.1.4 .Net Smart Card Properties	147
11.1.5 Communication Protocol	147
11.1.6 Card Certificate Requirements	147
11.1.7 Tested Smart Card Models	147
11.2 Using a Smart Card to Connect to a VMware View Brokered Session	148
Appendix A: Usage Examples Overview	151
A.1 Peer-to-Peer Direct Connection Example	151
A.1.1 Configuring the Client Peer-to-Peer Operation	151
A.1.2 Configuring the Host Peer-to-Peer Operation	152
A.1.3 Initiating the Peer-to-Peer Session	153
A.2 DHCP and Enable Host Discovery Example	154
A.2.1 Configuring the Client for DHCP and SLP Discovery	154
A.2.2 Configuring the Host for Host DHCP and SLP Discovery	156
A.2.3 Initiating an SLP Discovery Session	158
A.3 USB Permissions Example	158
A.3.1 Authorizing USB Device By Class	158
A.3.2 Authorizing USB Device By Vendor/Product ID	159
Appendix B: Client Language and Keyboard Support	161
B.1 Languages Supported by the Client	161