Kyocera KM-3035 3035/4035/5035 Operation Guide Rev-6.0 - Page 110

Section 5 OTHER CONVENIENT FUNCTIONS 2 Select how you want the copy sets to be finished by touching the "Staple mode" key, the "Saddle Stitch" ["Center Staple" ] key or the "Punch mode" key, as appropriate. Follow the instructions on the right side of the touch panel and verify the direction in which the originals were set. Inch specifications Ready to Job build. Place originals then press Start key. Finished Offset Staple No cover Staple Off mode On None Saddle Stitch Punch No cover Punch mode Set Back Close Check direction Check direction of original top side. Rear Left top corner Metric specifications Ready to Job build. Set original. Press Start key. Finished Group Group Staple None 1 set Off 1 set Staple Mode None Center Staple Punch Punch Mode Set Back Close Check direction Check direction of original. Back Edge Left top corner IMPORTANT! If the designation for the direction that the originals are set is not correct, copying may be accomplished incorrectly. 3 Touch the "Close" key. The touch panel will return to the screen in step 1. 5 Making copies at an enlarged or reduced magnification ratio This procedure selects the magnification ratio of the finished copies. 1 With the content of the "Basic" tab displayed, touch the "Reduce/Enlarge" key. The "Reduce/Enlarge" screen will be displayed. Inch specifications Ready to Job build. Place originals then press Start key. Job Build - Step1 11x81/2" Select paper Offset Finished Basic 1 sided Original type AMS Reduce /Enlarge Quality 1 sided copy 1 sided/ 2 sided Back Edge Orig. set direction Edit 1 sided copy-Left Finished page #:0 Set End Insert page Metric specifications Ready to Job build. Set original. Press Start key. Job Build-Step 1 Select paper Group Finished Basic 1-sided Original type AMS Reduce/ Enlarge Quality 1-sided Copy 1-sided/ 2-sided Back Edge Orig. set direction Edit 1-sided Copy-Left Finished page #: 0 Set End Insert blank page 2 Select the desired magnification ratio. If you want to have the copy magnification ratio selected automatically, touch the "AMS" key. If you want to manually set the magnification ratio, touch the "# keys" ["#-Keys"] key and then enter the desired ratio with the keypad, or touch the "+" key or the "-" key to change the displayed magnification ratio to the desired setting in 1% increments. You can also select the magnification ratio by touching the preset zoom ratio keys at the right that corresponds to the desired ratio. Inch specifications Ready to Job build. Place originals then press Start key. Reduce/Enlarge (25 400) 100 % Standard Zoom XY Zoom # keys Set Back Close AMS 100 % 400 % 200 % 51/2x81/2"R11x17" 154 % 51/2x81/2"R81/2x14" 129 % 81/2x11" R11x17" 121 % 81/2x14" R81/2x17" 78 % 81/2x14" R81/2x11" 77 % 11x17" R81/2x14" 64 % 11x17" R81/2x11" 50 % 11x17" R51/2x81/2" 25 % Metric specifications Ready to Job build. Set original. Press Start key. Reduce/Enlarge (25~400) 100 % Standard Zoom XY Zoom #-Keys AMS 100% 400% 200% Set Back Close A 5➔A 3 141% A 4➔A3 A 5➔A4 127% Folio➔A3 106% 11x15"➔A3 90% Folio➔A4 75% 11x15"➔A 4 70% A3➔A4 A4➔A5 50% 25% Metric specifications (Asia Pacific) Ready to Job build. Set original. Press Start key. Reduce/Enlarge (25~400) 100 % Standard Zoom XY Zoom #-Keys AMS 100% 400% 200% 141% 122% 115% 86% A 5➔A 3 Set Back Close A 4➔A 3 B 5➔B 4 A 4➔B 4 A 5➔B 5 B 4➔A 3 B 5➔A 4 A 3➔B 4 A 4➔B 5 81% 70% 50% 25% B 4➔A 4 B 5➔A 5 A 3➔A 4 B 4➔B 5 3 Touch the "Close" key. The touch panel will return to the screen in step 1. 5-64