Sharp MX-M260 MX-M260 MX-M310 Operation Manual - Page 119

Display Messages - install instruction

Get Sharp MX-M260 PDF manuals and user guides View all Sharp MX-M260 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 119 highlights

DISPLAY MESSAGES If one of the following messages appears in the display, take prompt action as instructed by the message. Message ENTER YOUR ACCOUNT NUMBER. A MISFEED HAS OCCURRED. 2-SIDED COPIES CANNOT BE MADE ON THIS PAPER TYPE. REMOVE PAPER FROM THE TRAY. CLOSE THE COVER. PLEASE EXTEND BYPASS-TRAY. COVER SHEETS MUST BE THE SAME SIZE AS THE COPY PAPER USED. PREPARE A NEW ONE. TONER SUPPLY IS LOW. CHANGE THE TONER CARTRIDGE. CHECK THE TONER CARTRIDGE. THE DOCUMENT FEEDER IS DISABLED. SELECTED PAPER TRAY IS PROHIBITED. PLEASE SELECT ANOTHER PAPER TRAY. PLEASE CHECK THE PAPER SIZE OF TRAY . ADD STAPLES. PLEASE REMOVE PAPER FROM THE STAPLER COMPILER. MEMORY IS FULL. PRESS [START] TO BEGIN COPYING OR [CA] TO CANCEL. Cause and solution Auditing mode is enabled. Enter your account number. Remove the misfeed as explained in "MISFEED REMOVAL". This appears when you attempt to make two-sided copies on special paper that cannot be used for two-sided copying. Cancel two-sided copying or change the paper. The indicated output tray is full. Remove the output from the tray. ( indicates the tray that is full.) The indicated cover is open. Close the cover. ( indicates the cover that is open.) When copying from the bypass tray, be sure to pull out the bypass tray extension. When adding a cover, load paper in the bypass tray that is the same size as the paper in the tray selected for copying. The toner cartridge must be prepared. The toner cartridge must be replaced soon. The toner cartridge is out of toner. Replace the toner cartridge. Make sure that the toner cartridge is installed correctly. The RSPF has been disabled in the administrator settings. Use the document glass. This appears when a tray is selected that has been prohibited in "TRAY SETTINGS" in the system settings. The tray's paper size setting is different from the actual paper size. Load the correct size of paper. The tray is indicated in . The finisher is out of staples. Replace the staple cartridge as explained in "STAPLE CARTRIDGE REPLACEMENT". Paper remains in the stapler compiler. Remove the paper. The memory becomes full while scanning originals. Press the [START] key ( ) to copy only the originals that have been scanned, or press the [CLEAR ALL] key ( ) to cancel the job. Page 95 127 16, 28 19 49 134 134 134 134 23 92 16 135 133 - 7 117

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
117
7
DISPLAY MESSAGES
If one of the following messages appears in the display, take prompt action as instructed by the message.
Message
Cause and solution
Page
ENTER YOUR ACCOUNT
NUMBER.
Auditing mode is enabled. Enter your account number.
95
A MISFEED HAS OCCURRED.
Remove the misfeed as explained in "MISFEED REMOVAL".
127
2-SIDED COPIES CANNOT BE
MADE ON THIS PAPER TYPE.
This appears when you attempt to make two-sided copies on special
paper that cannot be used for two-sided copying. Cancel two-sided
copying or change the paper.
16, 28
REMOVE PAPER FROM THE
<*>TRAY.
The indicated output tray is full. Remove the output from the tray.
(<*> indicates the tray that is full.)
-
CLOSE THE <**> COVER.
The indicated cover is open. Close the cover. (<**> indicates the
cover that is open.)
-
PLEASE EXTEND BYPASS-TRAY.
When copying from the bypass tray, be sure to pull out the bypass
tray extension.
19
COVER SHEETS MUST BE THE
SAME SIZE AS
THE COPY
PAPER USED.
When adding a cover, load paper in the bypass tray that is the
same size as the paper in the tray selected for copying.
49
PREPARE A NEW ONE.
The toner cartridge must be prepared.
134
TONER SUPPLY IS LOW.
The toner cartridge must be replaced soon.
134
CHANGE THE TONER CARTRIDGE.
The toner cartridge is out of toner. Replace the toner cartridge.
134
CHECK THE TONER CARTRIDGE.
Make sure that the toner cartridge is installed correctly.
134
THE DOCUMENT FEEDER IS
DISABLED.
The RSPF has been disabled in the administrator settings. Use
the document glass.
23
SELECTED PAPER TRAY IS
PROHIBITED. PLEASE SELECT
ANOTHER PAPER TRAY.
This appears when a tray is selected that has been prohibited in
"TRAY SETTINGS" in the system settings.
92
PLEASE CHECK THE PAPER
SIZE OF TRAY <***>.
The tray's paper size setting is different from the actual paper size.
Load the correct size of paper. The tray is indicated in <***>.
16
ADD STAPLES.
The finisher is out of staples. Replace the staple cartridge as
explained in
"STAPLE CARTRIDGE REPLACEMENT".
135
PLEASE REMOVE PAPER FROM
THE STAPLER COMPILER.
Paper remains in the stapler compiler. Remove the paper.
133
MEMORY IS FULL. PRESS [START]
TO BEGIN COPYING OR [CA] TO
CANCEL.
The memory becomes full while scanning originals.
Press the
[START] key (
) to copy only the originals that have been
scanned, or press the [CLEAR ALL] key (
) to cancel the job.
-