Brother International PE-DESIGN PLUS2 Instruction Manual - Page 95

Tutorial 8: Creating Design for Multi-Position Hoops, Creating the design

Get Brother International PE-DESIGN PLUS2 PDF manuals and user guides View all Brother International PE-DESIGN PLUS2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 95 highlights

Tutorial 8: Creating Design for Multi-Position Hoops b • Settings for multi-position hoops are indicated by " ". • Choose the appropriate setting after checking the size of the hoop available for your machine. Step 2 Creating the design 1 The Design Page appears on the screen as shown below. a 2 Create the design, making sure that it meets the following conditions. a b c b c b • Area - Area a Embroidering area when the multi-position hoop is installed at the top installation position. - Area b Embroidering area when the multi-position hoop is installed at the middle installation position. - Area c Embroidering area when the multi-position hoop is installed at the bottom installation position. The dotted lines separate each area. • If the [Rotate 90 Degrees] check box is selected, the embroidering areas appear as shown below. a b c • The size of one pattern must be no larger than 100 × 100 mm (or 130 × 180 mm). • Each pattern must completely fit within a single area (a, b, or c). b a 1 4 b 23 c 1: The position of this pattern is correct since it fits completely within area a. 2: The position of this pattern is correct since it fits completely within either area b or area c. 3: The size of this pattern is acceptable, but its position must be corrected since it does not fit completely within any of the areas. (It will be necessary to correct the position in order to fit in either b or c.) 4: This pattern must be corrected since it is too large. (It will be necessary to correct the position and size in order to fit in either a, b, or c.) 94

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
94
Tutorial 8: Creating Design for Multi-Position Hoops
1
The Design Page appears on the screen as
shown below.
2
Create the design, making sure that it meets
the following conditions.
•
The size of one pattern must be no larger
than 100 × 100 mm (or 130 × 180 mm).
•
Each pattern must completely fit within a
single area (a, b, or c).
b
•
Settings for multi-position hoops are indicated
by "
".
•
Choose the appropriate setting after checking
the size of the hoop available for your machine.
Step 2
Creating the design
b
• Area
-
Area a
Embroidering area when the multi-position
hoop is installed at the top installation position.
-
Area b
Embroidering area when the multi-position
hoop is installed at the middle installation
position.
-
Area c
Embroidering area when the multi-position
hoop is installed at the bottom installation
position.
The dotted lines separate each area.
•
If the
[Rotate 90 Degrees]
check box is
selected, the embroidering areas appear as
shown below.
a
b
c
a
b
c
b
1: The position of this pattern is correct since it fits
completely within area a.
2: The position of this pattern is correct since it fits
completely within either area b or area c.
3: The size of this pattern is acceptable, but its
position must be corrected since it does not fit
completely within any of the areas.
(It will be necessary to correct the position in
order to fit in either b or c.)
4: This pattern must be corrected since it is too
large.
(It will be necessary to correct the position and
size in order to fit in either a, b, or c.)
a
b
c
a
b
c
4
3
2
1