Dell PowerEdge T100 Hardware Owner's Manual - Page 101

Drive cage cooling fan cable to the HDD_FAN connector

Get Dell PowerEdge T100 PDF manuals and user guides View all Dell PowerEdge T100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 101 highlights

6 Install the expansion cards and connect any cables. See "Installing an Expansion Card" on page 72. 7 Depending on your configuration, connect the following cables that you removed in "Removing the System Board" on page 99. See Figure 6-2. • Two power-supply cables to the PWR_CONN and 12V connectors • If applicable, diskette data cable to the FLOPPY connector • I/O panel cable to the CONTROL_PANEL connector • Processor cooling fan cable to the CPU_FAN connector • Drive cage cooling fan cable to the HDD_FAN connector • SATA hard-drive data cable(s) to the SATA connector(s) • Intrusion switch cable from the INTRUSION SWITCH connector 8 Close the system. See "Closing the System" on page 47. 9 Reconnect the system to the electrical outlet, and turn on the system. Installing System Components 101

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
Installing System Components
101
6
Install the expansion cards and connect any cables. See "Installing an
Expansion Card" on page 72.
7
Depending on your configuration, connect the following cables that you
removed in "Removing the System Board" on page 99. See Figure 6-2.
•
Two power-supply cables to the PWR_CONN and 12V connectors
•
If applicable, diskette data cable to the FLOPPY connector
•
I/O panel cable to the CONTROL_PANEL connector
•
Processor cooling fan cable to the CPU_FAN connector
•
Drive cage cooling fan cable to the HDD_FAN connector
•
SATA hard-drive data cable(s) to the SATA connector(s)
•
Intrusion switch cable from the INTRUSION SWITCH connector
8
Close the system. See "Closing the System" on page 47.
9
Reconnect the system to the electrical outlet, and turn on the system.