Dell PowerEdge T100 Hardware Owner's Manual - Page 84

Press the side release tab that attaches the processor cooling fan to - sas controller guide

Get Dell PowerEdge T100 PDF manuals and user guides View all Dell PowerEdge T100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 84 highlights

3 Disconnect the fan's power cable from the system board. a If you are removing the smaller hard drive cooling fan (see Figure 3-23): b Squeeze the two release tabs together at the top of the fan cage that attaches the fan to the chassis bracket mount. c Lift the fan out. NOTE: The SAS hard drive cooling fan is present only if a SAS 6i/R integrated controller card is installed. 4 If you are removing the larger processor cooling fan: a Remove the heat sink and shroud assembly. See "Removing the Processor" on page 79. Do not remove the processor, however. b Press the side release tab that attaches the processor cooling fan to the chassis (see Figure 3-24). c Press the bottom release tab and shift it forward to guide the bottom mounting tabs out of their mounting holes (see Figure 3-24). d Slide the fan toward the back panel and lift the fan out. 84 Installing System Components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
84
Installing System Components
3
Disconnect the fan’s power cable from the system board.
a
If you are removing the smaller hard drive cooling fan (see
Figure 3-23):
b
Squeeze the two release tabs together at the top of the fan cage that
attaches the fan to the chassis bracket mount.
c
Lift the fan out.
NOTE:
The SAS hard drive cooling fan is present only if a SAS 6i/R integrated
controller card is installed.
4
If you are removing the larger processor cooling fan:
a
Remove the heat sink and shroud assembly. See "Removing the
Processor" on page 79. Do not remove the processor, however.
b
Press the side release tab that attaches the processor cooling fan to the
chassis (see Figure 3-24).
c
Press the bottom release tab and shift it forward to guide the bottom
mounting tabs out of their mounting holes (see Figure 3-24).
d
Slide the fan toward the back panel and lift the fan out.