Dell PowerEdge T100 Hardware Owner's Manual - Page 92

Installing the Power Supply, Chassis Intrusion Switch, Removing the Chassis Intrusion Switch

Get Dell PowerEdge T100 PDF manuals and user guides View all Dell PowerEdge T100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 92 highlights

Installing the Power Supply 1 Attach the cable clip to the new power supply. 2 Align the power supply mounting holes with the mounting holes on the back panel. 3 Slide the power supply toward the back panel until it snaps into place over the power-supply release tab. 4 Using a #2 Phillips screwdriver, install the four Phillips screws that secure the power supply to the back panel. 5 Reattach the I/O panel and SATA cables (if present) to the routing clip on the side of the power supply. 6 Depending on your system configuration, connect the following power cables: • PWR_CONN connector on the system board • 12V connector on the system board • Hard drives • Diskette drive • Tape backup unit • Optical drives 7 Close the system. See "Closing the System" on page 47. Chassis Intrusion Switch Removing the Chassis Intrusion Switch CAUTION: Only trained service technicians are authorized to remove the system cover and access any of the components inside the system. Before you begin this procedure, review the safety instructions that came with the system. 1 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet. 2 Open the system. See "Opening the System" on page 47. 3 Disconnect the chassis intrusion switch cable from the INTRUSION SWITCH connector on the system board. See Figure 3-28. 92 Installing System Components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
92
Installing System Components
Installing the Power Supply
1
Attach the cable clip to the new power supply.
2
Align the power supply mounting holes with the mounting holes on the
back panel.
3
Slide the power supply toward the back panel until it snaps into place over
the power-supply release tab.
4
Using a #2 Phillips screwdriver, install the four Phillips screws that secure
the power supply to the back panel.
5
Reattach the I/O panel and SATA cables (if present) to the routing clip on
the side of the power supply.
6
Depending on your system configuration, connect the following power
cables:
•
PWR_CONN connector on the system board
•
12V connector on the system board
•
Hard drives
•
Diskette drive
•
Tape backup unit
•
Optical drives
7
Close the system. See "Closing the System" on page 47.
Chassis Intrusion Switch
Removing the Chassis Intrusion Switch
CAUTION:
Only trained service technicians are authorized to remove the system
cover and access any of the components inside the system. Before you begin this
procedure, review the safety instructions that came with the system.
1
Turn off the system and attached peripherals, and disconnect the system
from the electrical outlet.
2
Open the system. See "Opening the System" on page 47.
3
Disconnect the chassis intrusion switch cable from the INTRUSION
SWITCH connector on the system board. See Figure 3-28.