HP LH4r HP NetRAID-4M Installation Guide - Page 12

System Requirements, A 75 MHz Pentium computer that complies with PCI Rev. 2.1

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

Hewlett-Packard NetRAID-4M Controller Installation Guide Tools and Capabilities BIOS CLI GUI Display file system type No Yes Yes Detect when the file system No can be extended Yes No Create, remove, or extend the No file system Yes No Detect when a container is a Yes (boot Yes Yes system or boot partition only) Synchronizes display between No GUI and DM No No 1 The disk always gets a signature to avoid NT disk administrator pop-ups. System Requirements The following are the minimum system requirements for the HP NetRAID-4M: s A 75 MHz Pentium computer that complies with PCI Rev. 2.1 or greater. If the Motherboard has bridged slots, then the bridge needs to be PCI Rev. 2.1 or greater compliant. s A minimum of 64 MBytes of main memory. s An available full length, either 32- or 64-bit 33 MHz, unobstructed 5-volt or 3.3-volt PCI slot that supports bus mastering and 5v power signalling. s One 64 MByte EDO DRAM DIMM (Dual-In Line Memory Module) with ECC for cache memory (included with controller). s 32 MBytes of available hard disk space for the HP NetRAID4M software. s One of the following: - Windows NT 4.0 Server, Small Business Server Edition. - Windows NT 4.0 Server, Terminal Server Edition. - Windows NT 4.0 Server, Enterprise Server Edition. - Windows NT 4.0 Server, BackOffice Edition. - Windows NT 4.0 Workstation (for installing the controller's GUI). 1-4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
1-4
Hewlett-Packard NetRAID-4M Controller Installation Guide
System Requirements
The following are the
minimum
system requirements for the
HP NetRAID-4M:
■
A 75 MHz Pentium computer that complies with PCI Rev. 2.1
or greater. If the Motherboard has bridged slots, then the
bridge needs to be PCI Rev. 2.1 or greater compliant.
■
A minimum of 64 MBytes of main memory.
■
An available full length, either 32- or 64-bit 33 MHz,
unobstructed 5-volt or 3.3-volt PCI slot that supports bus
mastering and 5v power signalling.
■
One 64 MByte EDO DRAM DIMM (Dual-In Line Memory
Module) with ECC for cache memory (included with
controller).
■
32 MBytes of available hard disk space for the HP NetRAID-
4M software.
■
One of the following:
–
Windows NT 4.0 Server, Small Business Server Edition.
–
Windows NT 4.0 Server, Terminal Server Edition.
–
Windows NT 4.0 Server, Enterprise Server Edition.
–
Windows NT 4.0 Server, BackOffice Edition.
–
Windows NT 4.0 Workstation (for installing the controller
’
s
GUI).
Display file system type
No
Yes
Yes
Detect when the file system
can be extended
No
Yes
No
Create, remove, or extend the
file system
No
Yes
No
Detect when a container is a
system or boot partition
Yes (boot
only)
Yes
Yes
Synchronizes display between
GUI and DM
No
No
No
1
The disk always gets a signature to avoid NT disk administrator pop-ups.
Tools and Capabilities
BIOS
CLI
GUI