HP LH4r HP NetRAID-4M Installation Guide - Page 42

Installing the Drivers During a Fresh Install of Windows 2000, see Appendix B

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Hewlett-Packard NetRAID-4M Controller Installation Guide The upgrade then continues to completion. 6 After the upgrade completes, reinstall the controller management software. For instructions on how to preform the installation, see Installing the Controller Management Software on page 5-2. Installing the Drivers During a Fresh Install of Windows 2000 Follow these instructions to install the Windows 2000 drivers while you are installing Windows 2000. Windows 2000 will be installed on a boot container if you create a boot container with the Container Configuration Utility. (For information on creating a boot container, see Appendix B, Using the BIOS Container Configuration Utility.) 1 Start your system with the Windows 2000 boot CD in the CD-ROM drive and proceed with the Windows 2000 installation. Note: To install Windows 2000 from a bootable CD, the CD-ROM drive must be connected to another SCSI controller or an IDE controller (not the HP NetRAID4M). 2 When the Windows 2000 CD starts to boot it will display the following message: Setup is inspecting your computer's hardware configuration.... Press F6 immediately. 3 A few seconds later a screen will be displayed asking you to specify additional adapters. 4 Press S to select additional hardware. 5 A menu with several items will be displayed. Be sure that Other is highlighted and then press Enter to load the device drivers. 6 You will be prompted to insert a diskette into drive A. Insert the diskette labeledNOS Drivers - Windows 2000 Disk #1. 7 Press Enter to start the load of the drivers. 4-8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
4-8
Hewlett-Packard NetRAID-4M Controller Installation Guide
The upgrade then continues to completion.
6
After the upgrade completes, reinstall the controller
management software. For instructions on how to preform the
installation, see
Installing the Controller Management Software
on
page 5-2.
Installing the Drivers During a Fresh Install of Windows
2000
Follow these instructions to install the Windows 2000
drivers while
you are installing Windows 2000. Windows 2000 will be installed on
a boot container if you create a boot container with the Container
Configuration Utility. (For information on creating a boot container,
see Appendix B,
Using the BIOS Container Configuration Utility
.)
1
Start your system with the Windows 2000 boot CD in the
CD-ROM drive and proceed with the Windows 2000
installation.
Note:
To install Windows 2000 from a bootable CD, the
CD-ROM drive must be connected to another SCSI
controller or an IDE controller (
not
the HP NetRAID-
4M).
2
When the Windows 2000 CD starts to boot it will display the
following message:
Setup is inspecting your computer’s hardware configuration
....
Press
F6
immediately.
3
A few seconds later a screen will be displayed asking you to
specify additional adapters.
4
Press
S
to select additional hardware.
5
A menu with several items will be displayed. Be sure that
Other
is highlighted and then press
Enter
to load the device
drivers.
6
You will be prompted to insert a diskette into drive
A
. Insert
the diskette labeled
NOS Drivers - Windows 2000 <NetServer
Name> Disk #1
.
7
Press
Enter
to start the load of the drivers.