HP LH4r HP NetRAID-4M Installation Guide - Page 56

Configuration Utility, in the first column to an

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

Hewlett-Packard NetRAID-4M Controller Installation Guide the HP NetRAID-4M controller, which on the open source distribution is called the aacraid driver. s Openserver Openserver does not require that you remove already existing drivers. s UnixWare a To determine if the hpnraid driver is installed on your UnixWare system, enter the following command: pkginfo hpnraid If the hpnraid driver exists on your UnixWare system, the pkginfo command will return a message like the following: system hpnraid Hewlett-Packard Raid Driver b If the hpnraid driver already exists on your UnixWare system, remove it by doing the following: i Execute the following command to access the Device Configuration Utility: /sbin/dcu ii Choose Hardware Device Configuration from the menu. iii Under the Device Name column, locate the entry hpnraid. iv Using the F2 key, change the Y in the first column to an N. v Press the F10 key to exit the Hardware Device Configuration. vi At the Device Configuration Utility main menu, choose Select Apply Changes & Exit DCU. vii Remove the hpnraid driver from the system by entering the following command: pkgrm hpnraid You will be prompted to confirm the deletion; answer yes to the prompt. 4-22

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
4-22
Hewlett-Packard NetRAID-4M Controller Installation Guide
the HP NetRAID-4M controller, which on the open source
distribution is called the
aacraid
driver.
■
Openserver
Openserver does not require that you remove already existing
drivers.
■
UnixWare
a
To determine if the
hpnraid
driver is installed on your
UnixWare system, enter the following command:
pkginfo hpnraid
If the
hpnraid
driver exists on your UnixWare system, the
pkginfo
command will return a message like the
following:
system hpnraid Hewlett-Packard Raid Driver
b
If the
hpnraid
driver already exists on your UnixWare
system, remove it by doing the following:
i
Execute the following command to access the Device
Configuration Utility:
/sbin/dcu
ii
Choose
Hardware Device Configuration
from the
menu.
iii
Under the
Device Name
column, locate the entry
hpnraid
.
iv
Using the
F2
key, change the
Y
in the first column to an
N
.
v
Press the
F10
key to exit the
Hardware Device
Configuration
.
vi
At the Device Configuration Utility main menu, choose
Select Apply Changes & Exit DCU
.
vii
Remove the
hpnraid
driver from the system by entering
the following command:
pkgrm hpnraid
You will be prompted to confirm the deletion; answer
yes
to the prompt.