HP LH4r HP NetRAID-4M Installation Guide - Page 18

Hewlett-Packard NetRAID-4M Controller Installation Guide

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Hewlett-Packard NetRAID-4M Controller Installation Guide Note: If the battery enable jumper is not connected or if the battery is disconnected from the two jumper pins, the controller will not pass the Power-On SelfTest (POST), and data is not accessible. 4 Insert the HP NetRAID-4M in the expansion slot as shown in Figure 2-3. Press down firmly so that the bus contacts are securely seated in the slot. Secure the bracket with the screw you removed in the previous step. Note: The HP NetRAID-4M should only be installed in a full-length PCI slot that includes a card support guide as shown in Figure 2-3. Due to the mass of the HP NetRAID-4M, this support is necessary to ensure reliable operation. Also, when inserting the HP NetRAID-4M be sure the bracket is aligned with the slot. 2-4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
2-4
Hewlett-Packard NetRAID-4M Controller Installation Guide
Note:
If the battery enable jumper is not connected or
if the battery is disconnected from the two jumper
pins, the controller will not pass the Power-On Self-
Test (POST), and data is not accessible.
4
Insert the HP NetRAID-4M in the expansion slot as shown in
Figure 2-3. Press down firmly so that the bus contacts are
securely seated in the slot. Secure the bracket with the screw
you removed in the previous step.
Note:
The HP NetRAID-4M should only be installed in
a full-length PCI slot that includes a card support
guide as shown in Figure 2-3. Due to the mass of the
HP NetRAID-4M, this support is necessary to ensure
reliable operation. Also, when inserting the
HP NetRAID-4M be sure the bracket is aligned with
the slot.