HP LH4r HP NetRAID-4M Installation Guide - Page 30

Configuring the Controller, Ctrl-A, Container Configuration Utility CCU

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

Hewlett-Packard NetRAID-4M Controller Installation Guide Channel 0 terminator (J2) Channel 1 terminator (J1) Channel 3 terminator (J7) Channel 4 terminator (J8) Figure 2-11. Channel Terminator Jumpers Configuring the Controller After connecting all devices, reinstall your computer cover, and connect all power cables. Turn on the external SCSI devices first, and then turn on the computer. During BIOS initialization, the HP NetRAID-4M BIOS banner should appear on the screen. If the BIOS banner does not appear, see Appendix C, Troubleshooting. Before installing the drivers and software for the HP NetRAID-4M controller, you may want to configure the controller and the SCSI devices connected to it (or if your controller and operating system support it, enable clustering support). To do this, press Ctrl-A when the following prompt appears: Press for Configuration Utility Three options for configuration are available: s Container Configuration Utility (CCU) - CCU allows you to create, delete, and manage containers from the HP NetRAID4M BIOS. You can use CCU to create a bootable container for the server. We recommend that you configure the server to boot from a container instead of from a single disk and install 2-16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
2-16
Hewlett-Packard NetRAID-4M Controller Installation Guide
Figure 2-11. Channel Terminator Jumpers
Configuring the Controller
After connecting all devices, reinstall your computer cover, and
connect all power cables. Turn on the external SCSI devices first, and
then turn on the computer. During BIOS initialization, the
HP NetRAID-4M BIOS banner should appear on the screen. If the
BIOS banner does not appear, see Appendix C,
Troubleshooting
.
Before installing the drivers and software for the HP NetRAID-4M
controller, you may want to configure the controller and the SCSI
devices connected to it (or if your controller and operating system
support it, enable clustering support). To do this, press
Ctrl-A
when
the following prompt appears:
Press <Ctrl><A> for Configuration Utility
Three options for configuration are available:
■
Container Configuration Utility (CCU) —
CCU allows you to
create, delete, and manage containers from the HP NetRAID-
4M BIOS. You can use CCU to create a bootable container for
the server. We recommend that you configure the server to
boot from a container instead of from a single disk and install
Channel 1 terminator (J1)
Channel 0 terminator (J2)
Channel 3 terminator (J7)
Channel 4 terminator (J8)