HP LH4r HP NetRAID-4M Installation Guide - Page 26

Ideally, the array enclosure itself should provide termination, pin connector.

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Hewlett-Packard NetRAID-4M Controller Installation Guide enclosures, refer to the documentation included with each enclosure. The following information is provided to help you properly connect your enclosure to the HP NetRAID-4M: s All rules for SCSI ID and termination (discussed on page 2-14) must be followed when installing SCSI devices in an array enclosure. The ID settings for the drives in the enclosure are determined by the slot, so drive ID jumpers should be removed. s The cable you use to connect the array enclosure to the HP NetRAID-4M must be equipped with a very high-density 68-pin connector. s Ideally, the array enclosure itself should provide termination capability, and you should disable termination on all the drives in the enclosure. s If the enclosure you are using for the array drives is not specifically designed as an array enclosure (such as a standard tower unit), be sure it has adequate cooling and ventilation. Array Enclosure Server Figure 2-9. Typical Dual-channel Array Enclosure Setup 2-12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
2-12
Hewlett-Packard NetRAID-4M Controller Installation Guide
enclosures, refer to the documentation included with each
enclosure.
The following information is provided to help you properly connect
your enclosure to the HP NetRAID-4M:
■
All rules for SCSI ID and termination (discussed on page 2-14)
must be followed when installing SCSI devices in an array
enclosure. The ID settings for the drives in the enclosure are
determined by the slot, so drive ID jumpers should be
removed.
■
The cable you use to connect the array enclosure to the
HP NetRAID-4M must be equipped with a very high-density
68-pin connector.
■
Ideally, the array enclosure itself should provide termination
capability, and you should disable termination on all the drives
in the enclosure.
■
If the enclosure you are using for the array drives is not
specifically designed as an array enclosure (such as a standard
tower unit), be sure it has adequate cooling and ventilation.
Figure 2-9. Typical Dual-channel Array Enclosure Setup
Array Enclosure
Server