HP LH4r HP NetRAID-4M Installation Guide - Page 45

netr4m.HAM Hewlett-Packard Array Controller, Save Parameters and Continue

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Installing the Device Drivers 5 When a screen appears that asks you to select a disk driver, check that the proper driver for any embedded SCSI controllers is installed. Note: If the embedded driver has not been installed, install it before installing the HP NetRAID-4M drivers. Refer to your Hewlett-Packard server documentation for further information. 6 Press Insert to install an unlisted driver. 7 Insert the HP NetRAID-4M NOS Driver - NetWare 4 driver diskette into your diskette drive. 8 An explanatory screen appears. Press Enter to have the system scan the diskette for the HP NetRAID-4M driver. 9 Select netr4m.HAM Hewlett-Packard Array Controller and press Enter. 10 Press Alt-Esc. From the console prompt type the following: load a:\netraid4m\netr4m.ham 11 Write down the slot number listed for the HP NetRAID-4M controller (you will need this in a later step) and press Enter. 12 Press Esc twice. 13 At the prompt, press Alt-Esc to return to the installation screen. 14 Select Select/Modify Driver Parameters, and then press Enter. 15 Type the slot number recorded in step 11. 16 Press F10, or Esc. 17 Select Save Parameters and Continue, and press Enter. 18 To install additional controllers, repeat step 14 through step 17. 19 When finished, select Continue the Installation to complete the installation. 20 If necessary, modify the load command line in the startup.ncf file so that the proper path to the driver and all appropriate command line options are specified. See Loading the NetWare Drivers at Server Bootup on page 4-17. 4-11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
4-11
Installing the Device Drivers
5
When a screen appears that asks you to select a disk driver,
check that the proper driver for any embedded SCSI
controllers is installed.
Note:
If the embedded driver has not been installed,
install it before installing the HP NetRAID-4M
drivers. Refer to your
Hewlett-Packard
server
documentation for further information.
6
Press
Insert
to install an unlisted driver.
7
Insert the HP NetRAID-4M
NOS Driver - NetWare 4
<NetServer Name>
driver diskette
into your diskette drive.
8
An explanatory screen appears. Press
Enter
to have the system
scan the diskette for the
HP NetRAID-4M driver.
9
Select
netr4m.HAM Hewlett-Packard Array Controller
and
press
Enter
.
10
Press
Alt-Esc
. From the console prompt type the following:
load a:\netraid4m\netr4m.ham
11
Write down the slot number listed for the HP NetRAID-4M
controller (you will need this in a later step) and press
Enter
.
12
Press
Esc
twice.
13
At the prompt, press
Alt-Esc
to return to the installation
screen.
14
Select
Select/Modify Driver Parameters
,
and then press
Enter
.
15
Type the slot number recorded in step 11.
16
Press
F10
, or
Esc
.
17
Select
Save Parameters and Continue
, and press
Enter
.
18
To install additional controllers, repeat step 14 through step 17.
19
When finished, select
Continue the Installation
to complete
the installation.
20
If necessary, modify the
load
command line in the
startup.ncf
file so that the proper path to the driver and all appropriate
command line options are specified. See
Loading the NetWare
Drivers at Server Bootup
on page 4-17.