HP LH4r HP NetRAID-4M Installation Guide - Page 19

Connecting the LED Activity Indicator to the HPNetRAID-4M, When removing the HP NetRAID-4M, always

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

Expansion Slot Cover Screw Bracket Installing the Hardware Bus Contacts Card Support Guide 32-bit PCI Expansion Slots 64-bit Expansion Slots Figure 2-3. Inserting the HP NetRAID-4M in a PCI Expansion Slot Note: When removing the HP NetRAID-4M, always replace the expansion slot bracket in the empty slot to ensure proper airflow. Connecting the LED Activity Indicator to the HP NetRAID-4M An LED on the front panel of most computers lights to indicate nonSCSI hard disk activity. If you would like that LED to light whenever there is activity on the HP NetRAID-4M instead, you must disconnect the LED cable from the motherboard and connect it to the LED connector on the HP NetRAID-4M, as shown in Figure 2-4. If the LED has a 2-pin cable and you would like to show activity on 2-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
2-5
Installing the Hardware
Figure 2-3. Inserting the HP NetRAID-4M in a PCI Expansion Slot
Note:
When removing the HP NetRAID-4M, always
replace the expansion slot bracket in the empty slot to
ensure proper airflow.
Connecting the LED Activity Indicator to the
HP NetRAID-4M
An LED on the front panel of most computers lights to indicate non-
SCSI hard disk activity. If you would like that LED to light whenever
there is activity on the HP NetRAID-4M instead, you must
disconnect the LED cable from the motherboard and connect it to
the LED connector on the HP NetRAID-4M, as shown in Figure 2-4.
If the LED has a 2-pin cable and you would like to show activity on
Expansion Slot
Cover Screw
Bracket
32-bit PCI
Expansion Slots
64-bit Expansion Slots
Bus Contacts
Card Support
Guide