Dell PowerEdge XE2420 EMC Installation and Service Manual - Page 100

Installing the intrusion switch, Intrusion switch removal

Get Dell PowerEdge XE2420 PDF manuals and user guides View all Dell PowerEdge XE2420 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 100 highlights

Figure 77. Intrusion switch removal Next steps Replace the intrusion switch. Installing the intrusion switch Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in the Before working inside your system. 3. Remove the GPU riser 2. 4. Remove the NVME riser. Steps 1. Align and slide the intrusion switch in the slot until it is firmly seated in the slot on the system. NOTE: Route the cable properly when you replace it to prevent the cable from being pinched or crimped. 2. Connect the intrusion switch cable to the connector on the system board. Figure 78. Intrusion switch installation 100 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
Figure 77. Intrusion switch removal
Next steps
Replace the intrusion switch
.
Installing the intrusion switch
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside your system
.
3.
Remove the GPU riser 2.
4.
Remove the NVME riser.
Steps
1.
Align and slide the intrusion switch in the slot until it is firmly seated in the slot on the system.
NOTE:
Route the cable properly when you replace it to prevent the cable from being pinched or crimped.
2.
Connect the intrusion switch cable to the connector on the system board.
Figure 78. Intrusion switch installation
100
Installing and removing system components