Dell PowerEdge XE2420 EMC Installation and Service Manual - Page 39

NVMe Settings, Boot Settings, Table 14. SATA Settings details continued, Table 15. Port n

Page 39 highlights

Table 14. SATA Settings details (continued) Option Description Table 15. Port n Options Model Drive Type Capacity Descriptions Specifies the drive model of the selected device. Specifies the type of drive attached to the SATA port. Specifies the total capacity of the drive. This field is undefined for removable media devices such as optical drives. NVMe Settings This option sets the NVMe drive mode. If the system contains NVMe drives that you want to configure in a RAID array, you must set both this field and the Embedded SATA field on the SATA settings menu to RAID Mode. You may also need to change the Boot Mode setting to UEFI. The option is set to Non-RAID mode by default. Boot Settings You can use the Boot Settings screen to set the boot mode to either BIOS or UEFI. It also enables you to specify the boot order. ● UEFI: The Unified Extensible Firmware Interface (UEFI) is a new interface between operating systems and platform firmware. The interface consists of data tables with platform related information, boot and runtime service calls that are available to the operating system and its loader. The following benefits are available when the Boot Mode is set to UEFI: ○ Support for drive partitions larger than 2 TB. ○ Enhanced security (e.g., UEFI Secure Boot). ○ Faster boot time. NOTE: You must use only the UEFI boot mode in order to boot from NVMe drives. ● BIOS: The BIOS Boot Mode is the legacy boot mode. It is maintained for backward compatibility. To view the Boot Settings screen, power on the system, press F2, and click System Setup Main Menu > System BIOS > Boot Settings. Table 16. Boot Settings details Option Boot Mode Description Enables you to set the boot mode of the system. If the operating system supports UEFI, you can set this option to UEFI. Setting this field to BIOS allows compatibility with non-UEFI operating systems. This option is set to UEFI by default. CAUTION: Switching the boot mode may prevent the system from booting if the operating system is not installed in the same boot mode. NOTE: Setting this field to UEFI disables the BIOS Boot Settings menu. Boot Sequence Retry Hard-disk Failover Generic USB Boot Enables or disables the Boot Sequence Retry feature. If this option is set to Enabled and the system fails to boot, the system re-attempts the boot sequence after 30 seconds. This option is set to Enabled by default. Enables or disables the Hard-disk failover. This option is set to Disabled by default. Enables or disables the generic USB boot placeholder. This option is set to Disabled by default. Pre-operating system management applications 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177

Table 14. SATA Settings details (continued)
Option
Description
Table 15. Port n
Options
Descriptions
Model
Specifies the drive model of the selected
device.
Drive Type
Specifies the type of drive attached to
the SATA port.
Capacity
Specifies the total capacity of the drive.
This field is undefined for removable
media devices such as optical drives.
NVMe Settings
This option sets the NVMe drive mode. If the system contains NVMe drives that you want to configure in a RAID array, you
must set both this field and the Embedded SATA field on the SATA settings menu to RAID Mode. You may also need to change
the Boot Mode setting to UEFI. The option is set to
Non-RAID
mode by default.
Boot Settings
You can use the
Boot Settings
screen to set the boot mode to either
BIOS
or
UEFI
. It also enables you to specify the boot
order.
UEFI
: The Unified Extensible Firmware Interface (UEFI) is a new interface between operating systems and platform
firmware. The interface consists of data tables with platform related information, boot and runtime service calls that are
available to the operating system and its loader. The following benefits are available when the
Boot Mode
is set to
UEFI
:
Support for drive partitions larger than 2 TB.
Enhanced security (e.g., UEFI Secure Boot).
Faster boot time.
NOTE:
You must use only the UEFI boot mode in order to boot from NVMe drives.
BIOS
: The
BIOS Boot Mode
is the legacy boot mode. It is maintained for backward compatibility.
To view the
Boot Settings
screen, power on the system, press F2, and click
System Setup Main Menu
>
System BIOS
>
Boot Settings
.
Table 16. Boot Settings details
Option
Description
Boot Mode
Enables you to set the boot mode of the system. If the operating system supports
UEFI, you can set this option to UEFI. Setting this field to BIOS allows compatibility
with non-UEFI operating systems. This option is set to
UEFI
by default.
CAUTION:
Switching the boot mode may prevent the system from
booting if the operating system is not installed in the same boot mode.
NOTE:
Setting this field to UEFI disables the
BIOS Boot Settings
menu.
Boot Sequence Retry
Enables or disables the
Boot Sequence Retry
feature. If this option is set to
Enabled
and the system fails to boot, the system re-attempts the boot sequence
after 30 seconds. This option is set to
Enabled
by default.
Hard-disk Failover
Enables or disables the Hard-disk failover. This option is set to
Disabled
by default.
Generic USB Boot
Enables or disables the generic USB boot placeholder. This option is set to
Disabled
by default.
Pre-operating system management applications
39