Dell PowerEdge XE2420 EMC Installation and Service Manual - Page 88

Removing the second drive bay assembly, Installing the primary drive bay assembly

Get Dell PowerEdge XE2420 PDF manuals and user guides View all Dell PowerEdge XE2420 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 88 highlights

Figure 63. Installing the primary drive bay assembly Next steps 1. Reconnect all the disconnected cables to the backplane. 2. Follow the procedure listed in After working inside your system. Removing the second drive bay assembly Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in the Safety instructions. 3. Remove the GPU riser 2 4. Disconnect cables from the interposer, primary backplane 1, and PIB. NOTE: Observe the routing of the cable as you remove it from the system. 5. Remove the slimline cable from the riser backplane. Steps 1. Loosen the one blue thumb screw located at the front of the assembly, and two blue thumb screws located at the rear of the assembly. 2. Hold the touch points, and lift the expansion card riser from the riser connector on the system board. 88 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
Figure 63. Installing the primary drive bay assembly
Next steps
1.
Reconnect all the disconnected cables to the backplane.
2.
Follow the procedure listed in
After working inside your system
.
Removing the second drive bay assembly
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in the
Safety instructions
.
3.
Remove the GPU riser 2
4.
Disconnect cables from the interposer, primary backplane 1, and PIB.
NOTE:
Observe the routing of the cable as you remove it from the system.
5.
Remove the slimline cable from the riser backplane.
Steps
1.
Loosen the one blue thumb screw located at the front of the assembly, and two blue thumb screws located at the rear of
the assembly.
2.
Hold the touch points, and lift the expansion card riser from the riser connector on the system board.
88
Installing and removing system components