Dell PowerEdge XE2420 EMC Installation and Service Manual - Page 90

Removing the EDSFF drive bay assembly, Removing the second drive bay assembly

Get Dell PowerEdge XE2420 PDF manuals and user guides View all Dell PowerEdge XE2420 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 90 highlights

Figure 65. Removing the second drive bay assembly Next steps 1. Connect the interposer cable at slot B1, PIB cables, cable on the primary backplane, and slimline cable on the secondary drive backplane. 2. Install the GPU riser 2 3. After working inside the system . Removing the EDSFF drive bay assembly Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in the Safety instructions. 3. Disconnect cables that are connected to the EDSFF switch backplane. NOTE: Observe the routing of the cable as you remove it from the system. Steps 1. Loosen the two blue thumbscrews at the rear of the assembly. 2. Hold the touch points, and slide the assembly towards the chassis front and lift it out of the system. 90 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
Figure 65. Removing the second drive bay assembly
Next steps
1.
Connect the interposer cable at slot B1, PIB cables, cable on the primary backplane, and slimline cable on the secondary drive
backplane.
2.
Install the GPU riser 2
3.
After working inside the system
.
Removing the EDSFF drive bay assembly
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in the
Safety instructions
.
3.
Disconnect cables that are connected to the EDSFF switch backplane.
NOTE:
Observe the routing of the cable as you remove it from the system.
Steps
1.
Loosen the two blue thumbscrews at the rear of the assembly.
2.
Hold the touch points, and slide the assembly towards the chassis front and lift it out of the system.
90
Installing and removing system components