Dell PowerEdge XE2420 EMC Installation and Service Manual - Page 137

Removing the BOSS card from the BOSS riser, BOSS riser installation

Get Dell PowerEdge XE2420 PDF manuals and user guides View all Dell PowerEdge XE2420 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 137 highlights

Figure 110. BOSS riser installation Next steps 1. Install the primary drive bay assembly. 2. Follow the procedure listed in the After working inside your system. Removing the BOSS card from the BOSS riser Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in the Before working inside your system. 3. Remove the primary drive bay assembly. 4. Remove the BOSS riser. Steps 1. Using the Phillips #1 screwdriver, remove the screws securing the BOSS card to the BOSS card riser. 2. Pull the latch away from the BOSS card to release the BOSS card. 3. Hold the BOSS card by its edges, and pull the card until the card edge connector disengages connector on the riser. Figure 111. BOSS card removal from BOSS riser Installing and removing system components 137

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
Figure 110. BOSS riser installation
Next steps
1.
Install the primary drive bay assembly.
2.
Follow the procedure listed in the
After working inside your system
.
Removing the BOSS card from the BOSS riser
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside your system
.
3.
Remove the primary drive bay assembly.
4.
Remove the BOSS riser.
Steps
1.
Using the Phillips #1 screwdriver, remove the screws securing the BOSS card to the BOSS card riser.
2.
Pull the latch away from the BOSS card to release the BOSS card.
3.
Hold the BOSS card by its edges, and pull the card until the card edge connector disengages connector on the riser.
Figure 111. BOSS card removal from BOSS riser
Installing and removing system components
137