Dell PowerEdge XE2420 EMC Installation and Service Manual - Page 92

Control panel, Removing the control panel

Get Dell PowerEdge XE2420 PDF manuals and user guides View all Dell PowerEdge XE2420 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 92 highlights

Figure 67. Installing the ESDFF drive bay assembly Next steps 1. Connect the cables to the EDSFF switch backplane. 2. After working inside the system . Control panel Removing the control panel Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in the Before working inside your system. 3. Remove the primary drive bay assembly. Steps 1. Disconnect the control panel cable from the control panel connector. NOTE: Observe the routing of the cable as you remove it from the system. 2. Using a Phillips #1 screwdriver, remove the screws that secure the control panel assembly to the server chassis. 3. Move the control panel assembly towards the left to release the lock and pull the assembly out of the server chassis. 92 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
Figure 67. Installing the ESDFF drive bay assembly
Next steps
1.
Connect the cables to the EDSFF switch backplane.
2.
After working inside the system
.
Control panel
Removing the control panel
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside your system
.
3.
Remove the primary drive bay assembly.
Steps
1.
Disconnect the control panel cable from the control panel connector.
NOTE:
Observe the routing of the cable as you remove it from the system.
2.
Using a Phillips #1 screwdriver, remove the screws that secure the control panel assembly to the server chassis.
3.
Move the control panel assembly towards the left to release the lock and pull the assembly out of the server chassis.
92
Installing and removing system components