Dell PowerEdge XE2420 EMC Installation and Service Manual - Page 9

PowerEdge XE2420 system overview, Front view of the System - server

Get Dell PowerEdge XE2420 PDF manuals and user guides View all Dell PowerEdge XE2420 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

2 PowerEdge XE2420 system overview The PowerEdge XE2420 system is a 2U server that supports: ● Two Intel Xeon Cascade Lake scalable processors up to 150 W ● 16 DDR4 RDIMM and Load Reduced DIMM ● Two, or four, 2.5-inch SATA, SAS, NVMe, or six EDSFF E1.L drives configuration. ● BOSS dual SATA M.2 boot card ● Two redundant 2000 W AC PSUs and 1100 W DC PSUs NOTE: For more information about how to hot swap NVMe PCIe SSD U.2 device, see the Dell Express Flash NVMe PCIe SSD User's Guide at https://www.dell.com/support> Browse all Products > Data Center Infrastructure > Storage Adapters & Controllers > Dell PowerEdge Express Flash NVMe PCIe SSD > Documentation > Manuals and Documents. NOTE: All instances of SAS, SATA drives are seen as drives in this document, unless specified otherwise. NOTE: In 2C configuration, hard drive slots 2 and 3 do not support NVMe drives if only processor 1 is installed. For more information about supported drives, see the Drive specifications section. NOTE: The PowerEdge XE2420 system is suitable for installation in Network Telecommunications Facilities (NTF), and locations where the National Electrical Code (NEC) applies. NOTE: The PowerEdge XE2420 system is suitable for Common Bonding Networks (CBNs). Topics: • Front view of the System • Rear view of the system • Inside the system • Locating the Express Service Code and Service Tag • System information label • Rail sizing and rack compatibility matrix Front view of the System Figure 1. Front view of 2 x 2.5-inch drive system PowerEdge XE2420 system overview 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
PowerEdge XE2420 system overview
The PowerEdge XE2420 system is a 2U server that supports:
●
Two Intel Xeon Cascade Lake scalable processors up to 150 W
●
16 DDR4 RDIMM and Load Reduced DIMM
●
Two, or four, 2.5-inch SATA, SAS, NVMe, or six EDSFF E1.L drives configuration.
●
BOSS dual SATA M.2 boot card
●
Two redundant 2000 W AC PSUs and 1100 W DC PSUs
NOTE:
For more information about how to hot swap NVMe PCIe SSD U.2 device, see the
Dell Express Flash NVMe PCIe
SSD User's Guide
at
> Browse all Products
>
Data Center Infrastructure
>
Storage
Adapters & Controllers
>
Dell PowerEdge Express Flash NVMe PCIe SSD
>
Documentation
>
Manuals and
Documents
.
NOTE:
All instances of SAS, SATA drives are seen as drives in this document, unless specified otherwise.
NOTE:
In 2C configuration, hard drive slots 2 and 3 do not support NVMe drives if only processor 1 is installed.
For more information about supported drives, see the
Drive specifications
section.
NOTE:
The PowerEdge XE2420 system is suitable for installation in Network Telecommunications Facilities (NTF), and
locations where the National Electrical Code (NEC) applies.
NOTE:
The PowerEdge XE2420 system is suitable for Common Bonding Networks (CBNs).
Topics:
•
Front view of the System
•
Rear view of the system
•
Inside the system
•
Locating the Express Service Code and Service Tag
•
System information label
•
Rail sizing and rack compatibility matrix
Front view of the System
Figure 1. Front view of 2 x 2.5-inch drive system
2
PowerEdge XE2420 system overview
9