Dell PowerEdge XE2420 EMC Installation and Service Manual - Page 138

Installing the BOSS card into the BOSS riser, Removing the M.2 SSD module

Get Dell PowerEdge XE2420 PDF manuals and user guides View all Dell PowerEdge XE2420 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 138 highlights

Next steps Replace the BOSS card into the BOSS riser. Installing the BOSS card into the BOSS riser Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in the Before working inside your system. 3. Remove the primary drive bay assembly. 4. Remove the BOSS riser. Steps 1. Pull the latch away from BOSS card connector. 2. Hold the edge of the BOSS card, and Align the BOSS card with the latch. 3. Insert the BOSS card edge connector firmly into the riser connector until the card is fully seated. 4. Using the Phillips #1 screwdriver, secure the BOSS card on the BOSS riser with the screw. Figure 112. Boss card installation into the BOSS riser Next steps 1. Install the BOSS riser. 2. Install the primary drive bay assembly. 3. Follow the procedure listed in the After working inside your system. Removing the M.2 SSD module Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in the Before working inside your system. 3. Remove the primary drive bay assembly. 4. Remove the BOSS riser. 5. Remove the BOSS card from the BOSS riser. Steps 1. Using the Phillips #1 screwdriver, remove the screws securing the M.2 SSD module to the BOSS card. 2. Pull the M.2 SSD module to disconnect from the connector on the BOSS card. 138 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
Next steps
Replace the BOSS card into the BOSS riser.
Installing the BOSS card into the BOSS riser
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside your system
.
3.
Remove the primary drive bay assembly.
4.
Remove the BOSS riser.
Steps
1.
Pull the latch away from BOSS card connector.
2.
Hold the edge of the BOSS card, and Align the BOSS card with the latch.
3.
Insert the BOSS card edge connector firmly into the riser connector until the card is fully seated.
4.
Using the Phillips #1 screwdriver, secure the BOSS card on the BOSS riser with the screw.
Figure 112. Boss card installation into the BOSS riser
Next steps
1.
Install the BOSS riser.
2.
Install the primary drive bay assembly.
3.
Follow the procedure listed in the
After working inside your system
.
Removing the M.2 SSD module
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside your system
.
3.
Remove the primary drive bay assembly.
4.
Remove the BOSS riser.
5.
Remove the BOSS card from the BOSS riser.
Steps
1.
Using the Phillips #1 screwdriver, remove the screws securing the M.2 SSD module to the BOSS card.
2.
Pull the M.2 SSD module to disconnect from the connector on the BOSS card.
138
Installing and removing system components