Dell PowerEdge XE2420 EMC Installation and Service Manual - Page 112

Removing GPU from GPU riser

Get Dell PowerEdge XE2420 PDF manuals and user guides View all Dell PowerEdge XE2420 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 112 highlights

3. If removed, install the GPU into the GPU riser. 4. If removed, install the network daughter card. 5. If removed, install the interposer. 6. If removed, install GPU riser 1 or second drive bay assembly. Steps 1. Holding the edges or the touch points, align the holes on the GPU riser bracket with the guides on the chassis. 2. Lower the GPU riser bracket into place and press the touch points until the expansion card riser connector is fully seated on the system board connector. 3. Tighten the one blue thumb screw located at the front of the assembly, and two blue thumb screws located at the rear of the assembly. 4. Re-connect the cables to the power interposer board. Figure 83. GPU riser 2 installation Next steps After working inside the system. Removing GPU from GPU riser Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in the Before working inside your system. 3. Remove the GPU riser 2 or GPU riser 1. 4. If applicable, disconnect the cables connected to the GPU. Steps 1. Open the GPU card holder latch. 2. Press the lock on the bottom of the GPU riser, and slide to release the card holder. 3. Hold the GPU, and pull the GPU until the card edge connector disengages from the expansion card connector on the riser. 112 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
3.
If removed,
install the GPU into the GPU riser
.
4.
If removed,
install the network daughter card
.
5.
If removed,
install the interposer.
6.
If removed,
install GPU riser 1
or
second drive bay assembly
.
Steps
1.
Holding the edges or the touch points, align the holes on the GPU riser bracket with the guides on the chassis.
2.
Lower the GPU riser bracket into place and press the touch points until the expansion card riser connector is fully seated on
the system board connector.
3.
Tighten the one blue thumb screw located at the front of the assembly, and two blue thumb screws located at the rear of
the assembly.
4.
Re-connect the cables to the power interposer board.
Figure 83. GPU riser 2 installation
Next steps
After working inside the system
.
Removing GPU from GPU riser
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside your system
.
3.
Remove the
GPU riser 2
or
GPU riser 1.
4.
If applicable, disconnect the cables connected to the GPU.
Steps
1.
Open the GPU card holder latch.
2.
Press the lock on the bottom of the GPU riser, and slide to release the card holder.
3.
Hold the GPU, and pull the GPU until the card edge connector disengages from the expansion card connector on the riser.
112
Installing and removing system components