Dell PowerEdge XE2420 EMC Installation and Service Manual - Page 117

Installing the GPU riser 1, GPU riser 1 removal

Get Dell PowerEdge XE2420 PDF manuals and user guides View all Dell PowerEdge XE2420 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 117 highlights

Figure 88. GPU riser 1 removal Next steps Replace the GPU riser 1. Installing the GPU riser 1 Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in the Before working inside your system. 3. If removed, install the GPU in the GPU riser. Steps 1. Holding the edges or the touch points, align the holes on the expansion card riser with the guides on the chassis. 2. Lower the whole assembly into place and press the touch points until it is fully seated. 3. Tighten the one blue thumb screw located at the front of the assembly, and two blue thumb screws located at the rear or the assembly. 4. Re-connect the cables to the interposer and power interposer board. Installing and removing system components 117

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
Figure 88. GPU riser 1 removal
Next steps
Replace the GPU riser 1
.
Installing the GPU riser 1
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside your system
.
3.
If removed,
install the GPU in the GPU riser
.
Steps
1.
Holding the edges or the touch points, align the holes on the expansion card riser with the guides on the chassis.
2.
Lower the whole assembly into place and press the touch points until it is fully seated.
3.
Tighten the one blue thumb screw located at the front of the assembly, and two blue thumb screws located at the rear or
the assembly.
4.
Re-connect the cables to the interposer and power interposer board.
Installing and removing system components
117