Dell PowerEdge XE2420 EMC Installation and Service Manual - Page 133

Micro SD card, Removing the MicroSD card

Get Dell PowerEdge XE2420 PDF manuals and user guides View all Dell PowerEdge XE2420 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 133 highlights

Figure 106. Installing the IDSDM module Next steps 1. Install the MicroSD cards. NOTE: Reinstall the MicroSD cards into the same slots based on the labels you had marked on the cards during removal. 2. Follow the procedure listed in the After working inside your system on page 54. Micro SD card Removing the MicroSD card Prerequisites 1. Follow the safety guidelines listed in the Safety instructions on page 53. 2. Follow the procedure listed in the Before working inside your system on page 54. 3. Remove the IDSDM module. Steps 1. Locate the MicroSD card slot on the IDSDM module, and press the card to partially release it from the slot. For more information on the slot location, see System board jumpers and connectors section. 2. Hold the MicroSD card and remove it from the slot.. NOTE: Temporarily label each MicroSD card with its corresponding slot number after removal. Installing and removing system components 133

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
Figure 106. Installing the IDSDM module
Next steps
1.
Install the MicroSD cards
.
NOTE:
Reinstall the MicroSD cards into the same slots based on the labels you had marked on the cards during removal.
2.
Follow the procedure listed in the
After working inside your system
on page 54.
Micro SD card
Removing the MicroSD card
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
on page 53.
2.
Follow the procedure listed in the
Before working inside your system
on page 54.
3.
Remove the IDSDM module
.
Steps
1.
Locate the MicroSD card slot on the IDSDM module, and press the card to partially release it from the slot. For more
information on the slot location, see System board jumpers and connectors section.
2.
Hold the MicroSD card and remove it from the slot..
NOTE:
Temporarily label each MicroSD card with its corresponding slot number after removal.
Installing and removing system components
133