Dell PowerEdge XE2420 EMC Installation and Service Manual - Page 86

Primary drive bay assembly, Removing the primary drive bay assembly

Get Dell PowerEdge XE2420 PDF manuals and user guides View all Dell PowerEdge XE2420 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 86 highlights

Figure 61. EDSFF switch backplane board installation Next steps 1. Install the EDSFF switch backplane assembly. 2. Connect all the cables to the EDSFF switch backplane. 3. Install all the EDSFF drives. 4. Follow the procedure listed in After working inside your system. Primary drive bay assembly Removing the primary drive bay assembly Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in the Before working inside your system. 3. Disconnect all the cables connected to the backplane. NOTE: Observe the routing of the cable as you remove it from the system. Steps 1. Loosen the blue thumb screw located at the rear of the assembly. 2. Slide the assembly towards the front to unlock the assembly. 3. Lift the assembly out of the server. 86 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
Figure 61. EDSFF switch backplane board installation
Next steps
1.
Install the EDSFF switch backplane assembly.
2.
Connect all the cables to the EDSFF switch backplane.
3.
Install all the EDSFF drives.
4.
Follow the procedure listed in
After working inside your system
.
Primary drive bay assembly
Removing the primary drive bay assembly
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside your system
.
3.
Disconnect all the cables connected to the backplane.
NOTE:
Observe the routing of the cable as you remove it from the system.
Steps
1.
Loosen the blue thumb screw located at the rear of the assembly.
2.
Slide the assembly towards the front to unlock the assembly.
3.
Lift the assembly out of the server.
86
Installing and removing system components