HP 6125XLG R2306-HP 6125XLG Blade Switch Fundamentals Command Reference - Page 22

Syntax, Default, Views, Predefined user roles, Parameters, Usage guidelines, Examples, command

Get HP 6125XLG PDF manuals and user guides View all HP 6125XLG manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

Use undo auto-execute command to remove the configuration. Syntax auto-execute command command undo auto-execute command Default Command auto-execution is disabled. Views VTY user interface view Predefined user roles network-admin Parameters command: Specifies the command to be automatically executed. Usage guidelines The device automatically executes the specified command when a user logs in to the user interface, and closes the user connection after the command is executed. If the command triggers another task, the device does not close the user connection until the task is completed. Typically, you configure the auto-execute command telnet X.X.X.X command on the device so the device redirects a Telnet user to the host at X.X.X.X. In this case, the connection to the current device is closed when the user terminates the Telnet connection to X.X.X.X. This command is not supported on the AUX user interface. Examples # Configure the device to automatically Telnet to 192.168.1.41 after a user logs in to interface VTY 0. system-view [Sysname] user-interface vty 0 [Sysname-ui-vty0] auto-execute command telnet 192.168.1.41 % This action will lead to configuration failure through ui-vty0. Are you sure? [Y/N]:y [Sysname-ui-vty0] # To verify the configuration, Telnet to 192.168.1.40. The device automatically Telnets to 192.168.1.41, and the following output is displayed: C:\> telnet 192.168.1.40 * Copyright (c) 2010-2013 Hewlett-Packard Development Company, L.P. * * Without the owner's prior written consent, * * no decompiling or reverse-engineering shall be allowed. * Trying 192.168.1.41 ... Press CTRL+K to abort Connected to 192.168.1.41 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
15
Use
undo auto-execute command
to remove the configuration.
Syntax
auto-execute command
command
undo auto-execute command
Default
Command auto-execution is disabled.
Views
VTY user interface view
Predefined user roles
network-admin
Parameters
command
: Specifies the command to be automatically executed.
Usage guidelines
The device automatically executes the specified command when a user logs in to the user interface, and
closes the user connection after the command is executed. If the command triggers another task, the
device does not close the user connection until the task is completed.
Typically, you configure the
auto-execute command telnet
X.X.X.X
command on the device so the device
redirects a Telnet user to the host at X.X.X.X. In this case, the connection to the current device is closed
when the user terminates the Telnet connection to X.X.X.X.
This command is not supported on the AUX user interface.
Examples
# Configure the device to automatically Telnet to 192.168.1.41
after a user logs in to interface VTY 0.
<Sysname> system-view
[Sysname] user-interface vty 0
[Sysname-ui-vty0] auto-execute command telnet 192.168.1.41
% This action will lead to configuration failure through ui-vty0. Are you sure?
[Y/N]:y
[Sysname-ui-vty0]
# To verify the configuration, Telnet to 192.168.1.40.
The device automatically Telnets to 192.168.1.41, and the following output is displayed:
C:\> telnet 192.168.1.40
******************************************************************************
* Copyright (c) 2010-2013 Hewlett-Packard Development Company, L.P.
*
* Without the owner's prior written consent,
*
* no decompiling or reverse-engineering shall be allowed.
*
******************************************************************************
<Sysname>
Trying 192.168.1.41 ...
Press CTRL+K to abort
Connected to 192.168.1.41 ...
******************************************************************************